Panasonic DMC-FT2 Technical specifications

Basic Operating Instructions
Digital Camera
Model No. DMC-FT2
Before use, please read these instructions completely.
Please also refer to Operating
Instructions (PDF format)
recorded on the CD-ROM
containing the Operating Instructions
(supplied).
You can learn about advanced operation methods
and check the Troubleshooting.
until
2010/2/28
EB
Web Site: http://www.panasonic-europe.com
VQT2M41
Model number suffix “EB” denotes UK model.
DMC-FT2&TS2EB-VQT2M41_eng.book 1 ページ ２０１０年１月２９日 金曜日 午後７時５９分

VQT2M41 (ENG)
2
Dear Customer,
We would like to take this opportunity to thank you for purchasing this Panasonic
Digital Camera. Please read these Operating Instructions carefully and keep them
handy for future reference. Please note that the actual controls and components,
menu items, etc. of your Digital Camera may look somewhat different from those
shown in the illustrations in these Operating Instructions.
Carefully observe copyright laws.
•Recording of pre-recorded tapes or discs or other published or broadcast
material for purposes other than your own private use may infringe copyright
laws. Even for the purpose of private use, recording of certain material may be
restricted.
Information for Your Safety
Please be sure to read “(Important) About the waterproof/dustproof and
anti-shock performance of the camera”(P8) and “Maintenance and
waterproof performance”(P10) before using this unit underwater to
prevent the unit from being mishandled, which may cause water to seep in.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT
DAMAGE,
•DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING
OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH
AS VASES, SHALL BE PLACED ON THE APPARATUS.
•USE ONLY THE RECOMMENDED ACCESSORIES.
•DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT
AND SHALL BE EASILY ACCESSIBLE.
Product Identification Marking is located on the bottom of units.
DMC-FT2&TS2EB-VQT2M41_eng.book 2 ページ ２０１０年１月２９日 金曜日 午後７時５９分

3
(ENG) VQT2M41
Caution for AC mains lead
For your safety, please read the following
text carefully.
This appliance is supplied with a moulded
three pin mains plug for your safety and
convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced
please ensure that the replacement fuse
has a rating of 5-ampere and that it is
approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI
mark on the body of the fuse.
If the plug contains a removable fuse
cover you must ensure that it is refitted
when the fuse is replaced.
If you lose the fuse cover the plug must
not be used until a replacement cover is
obtained.
A replacement fuse cover can be
purchased from your local dealer.
CAUTION!
IF THE FITTED MOULDED PLUG IS
UNSUITABLE FOR THE SOCKET
OUTLET IN YOUR HOME THEN THE
FUSE SHOULD BE REMOVED AND
THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE
ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO ANY 13-
AMPERE SOCKET.
If a new plug is to be fitted please
observe the wiring code as stated below.
If in any doubt please consult a qualified
electrician.
IMPORTANT
The wires in this mains lead are coloured
in accordance with the following code:
Blue: Neutral, Brown: Live.
As these colours may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured Blue must be
connected to the terminal which is marked
with the letter N or coloured Black or Blue.
The wire which is coloured Brown must be
connected to the terminal which is marked
with the letter L or coloured Brown or Red.
WARNING: DO NOT CONNECT EITHER
WIRE TO THE EARTH TERMINAL
WHICH IS MARKED WITH THE LETTER
E, BY THE EARTH SYMBOL OR
COLOURED GREEN OR
GREEN/YELLOW.
THIS PLUG IS NOT WATERPROOF-
KEEP DRY.
Before use
Remove the connector cover.
How to replace the fuse
The location of the fuse differ according to
the type of AC mains plug (figures A and
B). Confirm the AC mains plug fitted and
follow the instructions below.
Illustrations may differ from actual AC
mains plug.
1. Open the fuse cover with a screwdriver.
2. Replace the fuse and close or attach
the fuse cover.
Fuse cover
Figure A Figure B
Figure A Figure B
Fuse
(5 ampere)
Fuse
(5 ampere)
VQT2M41~Safety_eng.fm 3 ページ ２０１０年１月３０日 土曜日 午後５時７分

VQT2M41 (ENG)
4
∫About the battery pack
•Do not heat or expose to flame.
•Do not leave the battery(ies) in an automobile exposed to direct sunlight for a
long period of time with doors and windows closed.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC or
incinerate.
VQT2M41~Safety_eng.fm 4 ページ ２０１０年１月３０日 土曜日 午後５時７分

5
(ENG) VQT2M41
∫About the battery charger
•The battery charger is in the standby condition when the AC power supply cord
is connected. The primary circuit is always “live” as long as the power cord is
connected to an electrical outlet.
∫Cautions for Use
•Always use a genuine Panasonic AC adaptor (DMW-AC5E; optional).
• Always use a genuine Panasonic multi conversion adaptor (DMW-MCA1; optional).
•When using an AC adaptor, use the AC cable supplied with the AC adaptor.
•Do not use any other AV cables except the supplied one.
•Do not use any other cables except a genuine Panasonic HDMI mini cable
(RP-CDHM15, RP-CDHM30; optional).
Part numbers: RP-CDHM15 (1.5 m) (5 feet), RP-CDHM30 (3.0 m) (10 feet)
•Do not use any other USB connection cables except the supplied one.
Keep the camera as far away as possible from electromagnetic equipment
(such as microwave ovens, TVs, video games etc.).
•If you use the camera on top of or near a TV, the pictures and sound on the
camera may be disrupted by electromagnetic wave radiation.
•Do not use the camera near cell phones because doing so may result in noise
adversely affecting the pictures and sound.
•Recorded data may be damaged, or pictures may be distorted, by strong
magnetic fields created by speakers or large motors.
•Electromagnetic wave radiation generated by microprocessors may adversely
affect the camera, disturbing the pictures and sound.
•If the camera is adversely affected by electromagnetic equipment and stops
functioning properly, turn the camera off and remove the battery or disconnect
AC adaptor (DMW-AC5E; optional). Then reinsert the battery or reconnect AC
adaptor and turn the camera on.
Do not use the camera near radio transmitters or high-voltage lines.
•If you record near radio transmitters or high-voltage lines, the recorded pictures
and sound may be adversely affected.
CAUTION!
•DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN
CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS
WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE
HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY
OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
•DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.
•DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED
CANDLES, ON THE UNIT.
•DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY
MANNER.
DMC-FT2&TS2EB-VQT2M41_eng.book 5 ページ ２０１０年１月２９日 金曜日 午後７時５９分

VQT2M41 (ENG)
6
Information for Users on Collection and Disposal of Old Equipment
and used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old
products and used batteries, please take them to applicable
collection points, in accordance with your national
legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you
will help to save valuable resources and prevent any
potential negative effects on human health and the
environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old
products and batteries, please contact your local
municipality, your waste disposal service or the point of sale
where you purchased the items.
Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment,
please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside the
European Union]
These symbols are only valid in the European Union. If you
wish to discard these items, please contact your local
authorities or dealer and ask for the correct method of
disposal.
Note for the battery symbol (bottom two symbol
examples):
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by
the Directive for the chemical involved.
Cd
VQT2M41~Safety_eng.fm 6 ページ ２０１０年２月３日 水曜日 午後３時４３分

7
(ENG) VQT2M41
Contents
Information for Your Safety ........................................................................... 2
(Important) About the waterproof/
dustproof and anti-shock performance of the camera................................... 8
Maintenance and waterproof performance ................................................. 10
• Using the camera underwater............................................................... 14
• Causes of water leak ............................................................................ 15
• Caring of the camera after using it underwater..................................... 16
Accessories................................................................................................. 18
Names of the Components ......................................................................... 20
Charging the Battery ................................................................................... 22
About the Built-in Memory/the Card ............................................................ 24
Inserting and Removing the Card (optional)/the Battery ............................. 25
Setting Date/Time (Clock Set)..................................................................... 26
• Changing the clock setting.................................................................... 26
Setting the Menu......................................................................................... 27
Selecting the [REC] Mode........................................................................... 28
Taking pictures using the automatic function
(ñ: Intelligent Auto Mode) ......................................................................... 29
• Scene detection .................................................................................... 30
• AF Tracking Function............................................................................ 30
Recording Motion Picture............................................................................ 31
Playing back Pictures ([NORMAL PLAY])................................................... 32
Deleting Pictures ......................................................................................... 33
Reading the Operating Instructions
(PDF format) ............................................................................................... 34
Specifications.............................................................................................. 36
DMC-FT2&TS2EB-VQT2M41_eng.book 7 ページ ２０１０年１月２９日 金曜日 午後７時５９分

VQT2M41 (ENG)
8
(Important) About the waterproof/
dustproof and anti-shock performance of
the camera
•Please observe the following precautions, and avoid using this camera in any
situation where the camera is subject to high water pressure. This camera’s
waterproof/dustproof rating complies with the “IPX8” and “IP6X” ratings.
Provided the care and maintenance guidelines described in this document are
strictly followed, this camera can operate underwater, to a depth not exceeding
10 m (33 feet) for a time not exceeding 60 minutes.¢1
•This camera also complies with “MIL-STD 810F (Method 516.5-Shock)”. The
camera has cleared a drop test from a height of 2 m (6.6 feet) onto 3 cm
(0.10 feet) thick plywood. In most cases this camera should not sustain any
damage if dropped from a height not exceeding 2 m (6.6 feet).¢2
•Supplied accessories are not waterproof (excluding hand strap/silicon jacket).
¢1 This means that the camera can be used underwater for specified time in
specified pressure in accordance with the handling method established by
Panasonic. This does not guarantee no destruction, no malfunction, or
waterproofing in all conditions.
¢2 This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.
Observe the following precautions and avoid using under water pressure
exceeding the guaranteed performance, and in an environment with
excessive dust or sand.
Waterproofing is not guaranteed if the unit is subject to an impact as a result
of being hit or dropped etc.
If an impact to the camera occurs, it should be inspected (subject to a fee) by
a Panasonic’s service centre to verify that the waterproofing is still effective.
Any malfunction caused by customer misuse, or mishandling will not be
covered by the warranty.
Note
•The picture can become whitish if there is dirt e.g. fingerprints on the lens.
When it is dirty, lightly wipe the surface of the lens with soft and dry cloth.
DMC-FT2&TS2EB-VQT2M41_eng.book 8 ページ ２０１０年１月２９日 金曜日 午後７時５９分

9
(ENG) VQT2M41
∫Handling of the camera
•Do not leave the camera for a long period of time in places where temperature is
very low (ski resort etc.) or very high [above 40 oC (104 oF)], inside a car under
strong sunlight, close to a heater, on the beach, etc. Waterproof performance
may be degraded.
•The inside of this unit is not waterproof. Do not open or close the card/battery
door or terminal cover close to the water by the sea, a lake or river, or with wet
hands.
•Waterproof function of the camera is for sea water and fresh water only.
•Operation may not be possible when snow or water on the zoom lever, mode
dial or camera [OFF/ON] button the buttons freezes at cold places like ski
resorts etc.
∫About the [PRECAUTIONS] demonstration display
•Please check beforehand to maintain the waterproof performance.
[PRECAUTIONS] is displayed when the power is turned
on for the first time after purchase, with the card/battery
door completely closed.
•The [PRECAUTIONS] screen will not display the next time
you turn on the power if you start the slide show by selecting
[YES], and then select [END] once it has completed. Select
[REPLAY] to see the slide show again.
Note
•It will automatically skip to clock setting screen if [NO] is selected before the
slide show starts.
•[PRECAUTIONS] is displayed every time the power is turned on if you exited the
slide show using a method other than selecting [END], such as turning off the
power while the slide show is playing.
•This can be also confirmed from [PRECAUTIONS] in the [SETUP] menu.
VQT2M41~Body1_eng.fm 9 ページ ２０１０年２月３日 水曜日 午後３時４４分

VQT2M41 (ENG)
10
Maintenance and waterproof performance
∫To prevent water leaking into the camera, observe the following
items before using it.
∫Check that there is enough remaining battery power or memory in
the card.
∫Do not open or close the card/battery door or terminal cover in
places with sand and dust, near water, or with wet hands.
∫At purchase, the [LOCK] switch is in the locked state. When opening
the card/battery door and terminal cover, first release the lock.
•Release the lock by sliding the [LOCK] switch in the direction of the arrow until
the red area becomes visible, and open the card/battery door and terminal
cover.
A: [LOCK] switch (grey part)
B: Locked state
C:Red part
D: Released state
DMC-FT2&TS2EB-VQT2M41_eng.book 10 ページ ２０１０年１月２９日 金曜日 午後７時５９分