Panasonic SDR-SW20PL User manual

© 2008 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
ORDER NO. VM0801003CE
B27
SD Video Camera
Model No.SDR-SW20P
SDR-SW20PC
SDR-SW20PL
SDR-SW20E
SDR-SW20EB
SDR-SW20EE
SDR-SW20EF
SDR-SW20EG
SDR-SW20EP
SDR-SW20GC
SDR-SW20GN
SDR-SW28GK
Vol. 1
Colour
(S)...........Silver Type
(R)...........Red Type

2
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precaution -------------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
2Warning--------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------4
2.3. Caution for AC Cord(For EB/GC) ----------------------5
2.4. How to Replace the Lithium Battery-------------------6
3 Service Navigation------------------------------------------------7
3.1. Introduction --------------------------------------------------7
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------7
3.3. Important Notice 1:(Other than U.S.A. and
Canadian Market)------------------------------------------7
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------8
4 Specifications ------------------------------------------------------9
5 Location of Controls and Components------------------ 11
6 Service Mode -----------------------------------------------------12
6.1. Lock Search History Indication -----------------------13
7 Service Fixture & Tools ---------------------------------------14
7.1. When Replacing the Main PCB ----------------------14
7.2. Service Position ------------------------------------------14
8 Disassembly and Assembly Instructions---------------15
8.1. Disassembly Flow Chart--------------------------------16
8.2. PCB Location----------------------------------------------16
8.3. Disassembly Procedure --------------------------------17
9 Measurements and Adjustments --------------------------30
9.1. Electric Adjustment --------------------------------------30
9.2. Repair Record---------------------------------------------31
10 Factory Setting---------------------------------------------------32
10.1. HOW TO TURN ON THE FACTORY
SETTINGS? -----------------------------------------------32
10.2. WHAT IS THE FACTORY SETTINGS? ------------32

3
1 Safety Precaution
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 MΩand 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1

4
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

5
2.3. Caution for AC Cord
(For EB/GC)
2.3.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASRA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2. Before Use
Remove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live

6
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the FRONT PCB. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B6801” at component side of FRONT PCB) and then replace it into new one.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML-614S/ZT Manufactured by Matsushita Battery Industrial Co.,Ltd.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for SDR-SW20/SW28 series, as well.

7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3. Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servicing at component level
without concerned equipment/facilites.
a. Schematic diagram, Block Diagram and PCB layout of MAIN PCB.
b. Parts list for invidual parts for MAIN PCB.
When a part replacement is required for repairing MAIN PCB, replace as an assembled parts. (Main PCB)
2. The following category is /are recycle module part. Please send it/them to Central Repair Center.
• MAIN PCB (VEP03H40A : SDR-SW20P/PC)
• MAIN PCB (VEP03H40B : SDR-SW20E/EF/EG)
• MAIN PCB (VEP03H40C : SDR-SW20GC)
• MAIN PCB (VEP03H40D : SDR-SW20EE)
• MAIN PCB (VEP03H40E : SDR-SW28GK)
• MAIN PCB (VEP03H40F : SDR-SW20EP)
• MAIN PCB (VEP03H40H : SDR-SW20PL)
• MAIN PCB (VEP03H40J : SDR-SW20EB)
• MAIN PCB (VEP03H40K : SDR-SW20GN)

8
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are six kinds of SDR-SW20/SW28.
• a) SDR-SW20P
• b) SDR-SW20PC
• c) SDR-SW20E/EB/EF/EG/EP
• d) SDR-SW20EE
• e) SDR-SW20GN
• f) SDR-SW20PL/GC, SDR-SW28GK
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main PCB.
3.4.1. Defining methods:
To define the model suffix to be serviced, refer to the rating label which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site
in “TSN system”, together with Maintenance software.

9
4 Specifications
For P/PC/PL areas
For other areas

10

11
5 Location of Controls and Components

12
6 Service Mode
1. Indication method of the service menu
Set the mode dial “Video playback“ mode.
2. While keep pressing the “[LEFT<] of cursor” button, “record” button and “delete” button for more than 3 seconds until the top
screen of the Service Menu being displayed.
Service mode menu
NOTE:
Do not using service mode except [ 4 ] of Service Menu.
3. End method of the top screen of the service menu
Top screen of the service menu is finished by POWER OFF.
Screen display Contents Function
4 Lock search history indication Display an error cord for three histories saved in EEPROM

13
6.1. Lock Search History Indication
1. Set the mode dial “Video playback“ mode.
2. While keep pressing the “[LEFT<] of cursor” button, “record” button and “delete” button for more than 3 seconds until the top
screen of the Service Menu being displayed.
3. Select [ 4 ] Lock search history indication.
Operation specifications
Indication contents
• Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
• The error cord contents which are displayed
Lock search history indication is finished by POWER OFF.
Error code Function
51 Focus control is abnormal
52 Zoom control is abnormal
53 OIS lens control is abnormal
33 Communication between camera to ARM is abnormal

14
7 Service Fixture & Tools
7.1. When Replacing the Main PCB
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in
“TSN system”, together with Maintenance software.
7.2. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection Form
1 VFK1364 FP6931 (MAIN) - CCD UNIT 14PIN 0.5 FFC
2 VFK1461 FP6971 (MAIN) - LENS UNIT 20PIN 0.5 FFC
3 VFK1388 FP6902 (MAIN) - FP4802 (FRONT) 12PIN 0.5 FFC
4 VFK1716 FP6903 (MAIN) - FP8101 (MONITOR) 25PIN 0.3 FFC
5 VFK1461 FP6905 (MAIN) - BATTERY CHATCER UNIT 20PIN 0.5 FFC
6 VFK1461 FP6961 (MAIN) - OPERATION FPC UNIT 20PIN 0.5 FFC
7 VFK1870 PS6901 (MAIN) - FP6001 (JACK) 20PIN B to B

15
8 Disassembly and Assembly Instructions
㪥㪦㪫㪜㪪㩷㪦㪥㩷㪩㪜㪧㪘㪠㪩㩷㪘㪥㪛㩷㪤㪘㪠㪥㪫㪜㪥㪘㪥㪚㪜㩷㪦㪝㩷㪫㪟㪜㩷㪬㪥㪠㪫
㪈㪅㩷㪚㫆㫅㪽㫀㫉㫄㩷㫋㪿㪼㩷㫊㫋㪸㫋㪼㩷㫆㪽㩷㫋㪿㪼㩷㫇㫆㫃㫂㪸㩷㪻㫆㫋㩷㫊㪿㪼㪼㫋㩷㪹㪼㪽㫆㫉㪼㩷㫊㫋㪸㫉㫋㫀㫅㪾㩷㫉㪼㫇㪸㫀㫉㩷㫆㫉㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼㪅㩷㩿㪫㪿㫉㪼㪼㩷㫇㪸㫉㫋㫊㩷㫆㪽㩷㫋㪿㪼㩷㪫㫉㫀㫇㫆㪻㪆㪣㪚㪛㪆㪤㪸㫀㫅㩷㪝㫉㪸㫄㪼㩷㪬㫅㫀㫋㪀
㪧㪦㪣㪢㪘㩷㪛㪦㪫㪪㩷㪪㪟㪜㪜㪫 㪪㫋㪸㫋㪼 㪩㪼㫇㪸㫀㫉㪆㪧㪼㫉㫀㫆㪻㫀㪺㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼 㪩㪼㫄㪸㫉㫂㫊㪆㪩㪼㫇㪸㫀㫉㩷㪺㫆㫅㪻㫀㫋㫀㫆㫅㫊
㪥㪦㪩㪤㪘㪣
㪩㪜㪧㪘㪠㪩㪘㪙㪣㪜
㪮㪿㪼㫅㩷㫋㪿㪼㩷㪧㪦㪣㪢㪘㩷㪛㪦㪫㩷㫊㪿㪼㪼㫋㫊㩷㪽㫆㫉㩷㪸㫃㫃㩷㫋㪿㫉㪼㪼㩷㫊㪼㪺㫋㫀㫆㫅㫊㩷㫆㪽㩷㫋㪿㪼㩷㪫㪩㪠㪧㪦㪛㪃
㪣㪚㪛㪃㩷㪸㫅㪻㩷㪤㪸㫀㫅㩷㪝㫉㪸㫄㪼㩷㪬㫅㫀㫋㩷㫀㫅㪻㫀㪺㪸㫋㪼㩷㫋㪿㪼㩷㫊㫋㪸㫋㪼㩷㫊㪿㫆㫎㫅㩷㫀㫅㩷㫋㪿㪼㩷㪽㫀㪾㫌㫉㪼㫊
㫆㫅㩷㫋㪿㪼㩷㫃㪼㪽㫋㪃㩷㫋㪿㪼㩷㫊㪼㪺㫋㫀㫆㫅㫊㩷㪺㪸㫅㩷㪹㪼㩷㫉㪼㫇㪸㫀㫉㪼㪻㪃㩷㪸㫅㪻㩷㫋㪿㪼㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼㩷㪽㫆㫉
㫋㪿㪼㫊㪼㩷㫇㪸㫉㫋㫊㩷㪺㪸㫅㩷㪹㪼㩷㪼㫏㪼㪺㫌㫋㪼㪻㪅㩷㪩㪼㫇㫃㪸㪺㪼㩷㪸㫃㫃㩷㪻㪼㫊㫀㪾㫅㪸㫋㪼㪻㩷㫇㪸㫉㫋㫊㪅
㪩㪼㪻㩷㫇㪸㫋㫋㪼㫉㫅
㪜㪯㪧㪦㪪㪜㪛㩷㪫㪦㩷㪮㪘㪫㪜㪩 㪬
㪬㪥㪩㪜㪧㪘㪠㪩㪘㪙㪣㪜
㪮㪿㪼㫅㩷㪸㫅㫐㩷㫆㪽㩷㫋㪿㪼㩷㪧㪦㪣㪢㪘㩷㪛㪦㪫㩷㫊㪿㪼㪼㫋㫊㩷㩿㪽㫆㫉㩷㪸㫅㫐㩷㫆㪽㩷㫋㪿㪼㩷㪫㪩㪠㪧㪦㪛㪃㩷㪣㪚㪛㪃
㪸㫅㪻㩷㪤㪸㫀㫅㩷㪝㫉㪸㫄㪼㩷㪬㫅㫀㫋㪀㩷㫀㫅㪻㫀㪺㪸㫋㪼㫊㩷㫋㪿㪼㩷㫊㫋㪸㫋㪼㩷㫊㪿㫆㫎㫅㩷㫀㫅㩷㫋㪿㪼㩷㪽㫀㪾㫌㫉㪼㩷㫆㫅㩷㫋㪿㪼
㫃㪼㪽㫋㪃㩷㫋㪿㪼㩷㫊㪼㪺㫋㫀㫆㫅㫊㩷㪺㪸㫅㫅㫆㫋㩷㪹㪼㩷㫉㪼㫇㪸㫀㫉㪼㪻㪃㩷㪸㫅㪻㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼㩷㪽㫆㫉㩷㫋㪿㪼㫊㪼
㫇㪸㫉㫋㫊㩷㪺㪸㫅㫅㫆㫋㩷㪹㪼㩷㪼㫏㪼㪺㫌㫋㪼㪻㪅
㪘㫃㫃㩷㫉㪼㪻
㪉㪅㩷㪧㪸㫉㫋㫊㩷㪻㪼㫊㫀㪾㫅㪸㫋㪼㪻㩷㪽㫆㫉㩷㫉㪼㫇㫃㪸㪺㪼㫄㪼㫅㫋㩷㪸㫋㩷㫋㪿㪼㩷㫋㫀㫄㪼㩷㫆㪽㩷㫉㪼㫇㪸㫀㫉㩷㫆㫉㩷㫇㪼㫉㫀㫆㪻㫀㪺㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼㪅
㩷㩿㪧㪸㫉㫋㫊㩷㫀㫅㩷㫆㫋㪿㪼㫉㫊㪼㪺㫋㫀㫆㫅㫊㩷㫆㫋㪿㪼㫉㩷㫋㪿㪸㫅㩷㫋㪿㪼㩷㫊㪼㪺㫋㫀㫆㫅㩷㫋㫆㩷㪹㪼㩷㫉㪼㫇㪸㫀㫉㪼㪻㩷㫄㫌㫊㫋㩷㪹㪼㩷㫉㪼㫇㫃㪸㪺㪼㪻㪅㩷㪩㪼㫇㫃㪸㪺㪼㩷㫎㪿㪼㫅㪼㫍㪼㫉㩷㫉㪼㫇㪸㫀㫉㫊㩷㪸㫉㪼㩷㫅㪼㪼㪻㪼㪻㪅㪀
㪘㫃㫃㩷㫋㪿㫉㪼㪼㩷㫂㫀㫅㪻㫊㩷㫆㪽㩷㪘㪆㪙㪆㪚㩷㫄㫌㫊㫋㩷㪹㪼㩷㫉㪼㫇㫃㪸㪺㪼㪻㪅㩷㪪㫀㫅㪺㪼㩷㫋㪿㪼㫊㪼㩷㫇㪸㫉㫋㫊㩷㪸㫉㪼㩷㫀㫅㫋㪼㪾㫉㪸㫋㪼㪻㩷㫀㫅㫋㫆㩷㪸㩷㫂㫀㫋㪃㩷㪸㫃㫃㩷㫇㪸㫉㫋㫊㩷㫀㫅㪺㫃㫌㪻㪼㪻㫄㫌㫊㫋㩷㪹㪼㩷㫉㪼㫇㫃㪸㪺㪼㪻㪅
㪫㪰㪧㪜 㪧㪘㪩㪫㪪㩷㪥㪘㪤㪜 㪧㪘㪩㪫㪪㩷㪥㪦㪅
㪩㪜㪝㪅㩷㪥㪦㪅
㩿㪚㪘㪙㪠㪥㪜㪫㩷㪧㪘㪩㪫㪪
㪣㪦㪚㪘㪫㪠㪦㪥㪀
㪩㪜㪤㪘㪩㪢㪪
㪘㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪩㪬㪙㪙㪜㪩㩷㪢㪠㪫 㪭㪬㪤㪞㪈㪎㪐㪈 㪊㪆㪎㪄㪈㪇㪆㪈㪌㪆㪊㪋㪄㪊㪎㪆㪌㪋㪆
㪌㪍㪆㪎㪉㪆㪎㪌㪆㪏㪊㪆㪏㪐
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪘 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪧㪩㪃㪧㪣㪩㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪙 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪧㪚㪩㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪚 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪜㪞㪩㪃㪜㪩㪃㪜㪙㪩㪃㪜㪝㪩㪃㪜㪧㪩㪃㪞㪚㪩㪃㪞㪥㪩㪃㪜㪜㪩㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪛 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪏㩷㪞㪢㪩㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪜 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪧㪪㪃㪧㪣㪪㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪝 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪧㪚㪪㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪞 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪇㩷㪜㪞㪪㪃㪜㪪㪃㪜㪙㪪㪃㪜㪝㪪㪃㪜㪧㪪㪃㪞㪚㪪㪃㪞㪥㪪㪃㪜㪜㪪㩷
㪙㪮㪘㪫㪜㪩㪧㪩㪦㪦㪝㩷㪚㪘㪙㪠㪥㪜㪫㩷㪢㪠㪫 㪭㪬㪰㪢㪉㪡㪊㪇㪟 㪉㪆㪈㪉㪆㪋㪏㪆㪌㪈㪆㪌㪊㪆㪏㪇㪆㪏㪍 㪪㪛㪩㪄㪪㪮㪉㪏㩷㪞㪢㪪㩷
㪚㪣㪚㪛㩷㪙㪦㪫㪫㪦㪤㩷㪚㪘㪪㪜㩷㪬㪥㪠㪫 㪭㪬㪢㪤㪎㪊㪋㪇 㪐㪊 㩿㪪㪠㪣㪭㪜㪩㪀
㪚㪣㪚㪛㩷㪙㪦㪫㪫㪦㪤㩷㪚㪘㪪㪜㩷㪬㪥㪠㪫 㪭㪬㪢㪤㪎㪊㪋㪌 㪐㪊 㩿㪩㪜㪛㪀
㪊㪅㩷㪫㫆㫆㫃㫊㩷㫉㪼㫈㫌㫀㫉㪼㪻㩷㪽㫆㫉㩷㫉㪼㫇㪸㫀㫉㫊㩷㪸㫅㪻㩷㫇㪼㫉㫀㫆㪻㫀㪺㩷㫄㪸㫀㫅㫋㪼㫅㪸㫅㪺㪼
㪞㪩㪜㪘㪪㪜㩷㪑㩷㪩㪝㪢㪱㪇㪋㪍㪊 㪪㪰㪩㪠㪥㪞㪜㩷㪑㩷㪩㪝㪢㪱㪇㪋㪎㪐 㪪㪠㪣㪠㪚㪦㪥㪜㩷㪫㪠㪧㪪㩷㪑㩷㪩㪝㪢㪱㪇㪋㪎㪏
㩿㪝㪣㪘㪫㩷㪚㪟㪠㪪㪜㪣㪀 㪫㪦㪩㪨㪬㪜㩷㪛㪩㪠㪭㪜㪩㩷㪑㩷㪩㪝㪢㪱㪇㪋㪌㪍
㪋㪅㩷㪪㪼㪺㫋㫀㫆㫅㫊㩷㫆㫋㪿㪼㫉㩷㫋㪿㪸㫅㩷㫋㪿㪼㩷㫄㪸㫀㫅㩷㫌㫅㫀㫋㩷㪺㪸㫊㪼㩷㪸㫅㪻㩷㫋㪿㪼㩷㪣㪚㪛㩷㪺㪸㫊㪼㩷㪦㪄㫉㫀㫅㪾㩷㫎㪿㪼㫉㪼㩷㪾㫉㪼㪸㫊㪼㩷㫄㫌㫊㫋㩷㪹㪼㩷㪸㫇㫇㫃㫀㪼㪻㪅㩿㪘㫇㫇㫃㫐㩷㫋㪿㪼㩷㪾㫉㪼㪸㫊㪼㩷㫀㫅㪻㫀㪺㪸㫋㪼㪻㩷㪹㫐㩷㫋㪿㪼㩷㩹㪯㪯㩹㪅㪀
㪦㪧㪜㪩㪘㪫㪠㪦㪥㩷㪙㪬㪫㪫㪦㪥 㪱㪦㪦㪤㩷㪙㪬㪫㪫㪦㪥 㪩㪜㪚㪦㪩㪛㩷㪙㪬㪫㪫㪦㪥
㪞㪥㪛㩷㪦㪄㪩㪠㪥㪞 㪫㪩㪠㪧㪦㪛㩷㪬㪥㪠㪫 㪪㪬㪙㩷㪩㪜㪚㪦㪩㪛㩷㪙㪬㪫㪫㪦㪥
㪌㪅㩷㪥㫆㫋㪼㫊㩷㫆㫅㩷㫌㫊㫀㫅㪾㩷㫋㪿㪼㩷㫊㪺㫉㪼㫎㫊
㪚㪼㫉㫋㪸㫀㫅㩷㫋㫆㫉㫈㫌㪼㩷㫍㪸㫃㫌㪼㫊㩷㪸㫉㪼㩷㪻㪼㫊㫀㪾㫅㪸㫋㪼㪻㩷㪽㫆㫉㩷㫋㫀㪾㪿㫋㪼㫅㫀㫅㪾㩷㫋㪿㪼㩷㫊㪺㫉㪼㫎㫊㩷㫀㫅㩷㫊㫆㫄㪼㩷㫊㪼㪺㫋㫀㫆㫅㫊㪅
㪫㫀㪾㪿㫋㪼㫅㩷㫋㪿㪼㩷㫊㪺㫉㪼㫎㫊㩷㫋㫆㩷㫋㪿㪼㩷㪻㪼㫊㫀㪾㫅㪸㫋㪼㪻㩷㫋㫆㫉㫈㫌㪼㩷㫍㪸㫃㫌㪼㩷㫀㫅㩷㫋㪿㪼㩷㫊㪼㪺㫋㫀㫆㫅㫊㩷㫀㫅㪻㫀㪺㪸㫋㪼㪻㩷㪻㫌㫉㫀㫅㪾㩷㪻㫀㫊㪸㫊㫊㪼㫄㪹㫃㫐㩷㫆㫉㩷㪸㫊㫊㪼㫄㪹㫃㫐㪅

16
8.1. Disassembly Flow Chart
8.2. PCB Location

17
8.3. Disassembly Procedure
No. Item Fig Removal
1 Front case unit Fig. D1 2 Screws (A)
Front case unit
2 Tripod piece Fig. D2 2 Screws (B)
Access panel light
Tripod O ring
Panel light O ring
Tripod piece
3 Rear cover Fig. D3 2 Screws (C)
Rear cover
4 R cover Fig. D4 2 Screws (D)
5 Locking tabs
Fig. D5 R cover
5 Lens piece,
Lens protection glass
Lens damper
Fig. D6 3 Screws (E)
Lens piece
Lens protection glass
Lens damper
6 Side case (L) unit Fig. D7 6 Screws (F)
Case O ring
FP4802(Flex)
1 Screw (G)
Battery cover
Side case (L) unit
Fig. D8 Attention when installing
the Case O ring
Fig. D9 NOTE: (When Installing)
7 Lens unit/Main P.C.B. Fig. D10 4 Screws (H)
FP6961(Flex)
P6901(Connector)
Fig. D11 FP6903(Flex)
Lens unit/Main P.C.B.
8 Radiation plate Fig. D12 4 Screws (I)
Radiation plate
9 Battery catcher unit Fig. D13 2 Screws (J)
FP6905(Flex)
Battery catcher unit
10 Main P.C.B.,
Jack P.C.B. Fig. D14 1 Screw (K)
FP6931(Flex)
FP6971(Flex)
FP6905(Flex)
2 Locking tabs
Fig. D15 FP6001(Connector)
Main P.C.B.
Jack P.C.B.
11 Lens unit Fig. D16 FP6931(Flex)
FP6971(Flex)
1 Screw (L)
1 Locking tab
Lens unit
12 Battery case Fig. D17 1 Screw (M)
2 Locking tabs
Battery case
13 Front P.C.B. Fig. D18 1 Screw (N)
2 Ribs
FP4801(Flex)
Front P.C.B.
14 LCD unit Fig. D19 R base rubber
4 Screw (N)
Fig. D20 GND O ring
LCD unit
15 LCD hinge unit,
Monitor P.C.B. Fig. D21 4 Screws (P)
Packing angle
4 screw O rings
2 Screws (Q)
Fig. D22 2 Locking tabs
LCD case top
FP8101(Flex)
3 Locking tabs
FP8102(Flex)
LCD hinge unit
Monitor P.C.B.
16 LCD panel Fig. D23 Reflection sheet
Lighting plate
Diffusion sheet
Prism sheet B
Prism sheet A
Light guide holder
LCD panel
LCD shield case
LCD case bottom unit
Fig. D24 Attention when installing
the LCD O ring
17 Speaker unit,
Operation FPC unit Fig. D25 9 Screws (R)
Operation angle
Earth angle
Speaker unit
Fig. D26 SS operation angle
Zoom operation angle
SS button rubber unit
Zoom OP rubber unit
Operation FPC unit
Fig. D27 NOTE: (When Installing)
18 CCD unit,
Optical filter Fig. D28 2 Screws (S)
CCD cushion rubber
CCD unit
Optical filter
19 IRIS unit Fig. D29 Solder (8 points)
3 Screws (T)
1 Rib
IRIS unit
Fig. D30 NOTE: (When Installing)
20 Zoom motor unit Fig. D31 2 Screws (U)
Zoom motor unit
21 Focus motor unit Fig. D32 2 Screws (V)
Focus motor unit
22 Master flange,
4th moving frame unit,
3rd moving frame unit
Fig. D33 3 Screws (W)
Master flange
4th moving frame unit
3rd moving frame unit
23 Guide pole S,
Guide pole,
2nd moving frame unit
Fig. D34 Guide pole S
Guide pole
2nd moving frame unit
No. Item Fig Removal

18
8.3.1. Removal of the Front case unit
Fig. D1
8.3.2. Removal of the Tripod piece
Fig. D2

19
8.3.3. Removal of the Rear cover
Fig. D3
8.3.4. Removal of the R cover
Fig. D4
Fig. D5
8.3.5. Removal of the Lens piece, Lens
protection glass and Lens damper
Fig. D6

20
8.3.6. Removal of the Side case (L) unit
Fig. D7
Fig. D8