Panasonic PVD4761 - DVD/VCR DECK User manual

PV-D4761
LSQT0453A
Connections and Initial Setup Procedures are on pages 12 to 17.
DVD/VCR DECK
Operating Instructions
Model No.
Please read these instructions carefully before attempting to connect, operate or
adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
VCR Plus+, A LL S ET and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
®
As an ENERGY STAR Partner, Matsushita Electric Corporation of
America has determined that this product or product model meets the
ENERGY STAR guidelines for energy efficiency.
®
Initial Setup
(Connection) Basic
Operation VCR
Operation For Your
Information
DVD
Operation
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

INSTALLATION
1 POWERSOURCECAUTION
Operate only from a power source indicated on the
unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.
2 POLARIZEDORGROUNDINGPLUG
As a safety feature, this product comes with either a
polarized power cord plug (one blade is wider than
the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.
GROUNDINGPLUGCAUTION:
This plug will only fit into a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not defeat the safety feature by tampering with the
plug.
3 POWERCORD
Make sure power cords are routed so that they are
not likely to have anything rest on them, roll over
them, or be in the way of walking traffic.
If an extension cord is used, make sure it also has
either a polarized or grounded plug and that the
cords can be securely connected. Frayed cords,
damaged plugs, and damaged or cracked wire
insulation are hazardous and should be replaced
by a qualified service technician.
Overloaded outlets and extension cords are fire
hazards and should be avoided.
4 DONOTBLOCKVENTILATIONHOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked, heat
build-up inside the unit can cause failures that may
result in a fire hazard or heat damage to cassettes
or discs.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in
use, or operate the unit when placed on a bed,
sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case or
rack, unless proper ventilation is provided.
5 PLACEMENT:AVOIDEXTREMELYHOTLOCATIONS
ORSUDDENTEMPERATURECHANGES
Do not place the unit over or near heater or radiator,
in direct sunlight, inside closed vehicles, in high
temperature [over 104°F (40°C)], or in over 75%
humidity. If the unit is suddenly moved from a cold
place to a warm one, moisture may condense in the
unit and on the tape causing damage. Never subject
the unit to vibration, impact, or place it so that the
surface is titled as internal parts may be seriously
damaged.
6 TO AVOID PERSONAL INJURY
•Do not place unsecured equipment on a sloping
surface.
•Do not place this unit on any support
that is not firm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult
and damage to the unit.
•An appliance and cart combination
should be moved with care.
Quick stops, excessive force, and
uneven surfaces may cause the
appliance and cart combination to overturn.
•Carefully follow all operating instructions and use
the manufacturer's recommended accessories
when operating this unit or connecting it to any
other equipment.
FORYOURSAFETY,READANDRETAINALLSAFETY
ANDOPERATINGINSTRUCTIONS.HEEDALL
WARNINGSINTHEMANUALANDONTHEUNIT
USINGTHEUNIT
If the unit has been in storage or moved to a new location, refer
first to the INSTALLATION section of these safeguards.
1 KEEPTHEUNITAWAYFROMWATERORMOISTUREOFANYKIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by
a qualified service technician before use.
3 DURINGANELECTRICALSTORM
During a lightning storm, whether indoors or outdoors, or before
leaving the unit unused for extended periods of time, disconnect
all equipment from the power source as well as the antenna and
cable system.
4 WHEN THE UNIT IS PLUGGED IN
•Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug the
unit, and have it inspected by a service technician. Fire and
shock hazards can result from electrical shorts caused by
liquid contact inside.
•Never drop or push any object through openings in the unit.
Some internal parts carry hazardous voltages and contact can
cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.
•Avoid placing the unit directly above or below your TV set as
this may cause electrical interference. Keep all magnets away
from electronic equipment.
5 USINGACCESSORIES
Use only accessories recommended by the manufacturer to avoid
risk of fire, shock, or other hazards.
6 CLEANINGTHEUNIT
Unplug the unit. Then, use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE cleaning
fluids, aerosols, or forced air that could over-spray, or seep into
the unit and cause electrical shock. Any substance such as wax,
adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely affect
internal parts. SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating instructions,
this product does not operate properly, do not attempt to open
or remove covers, or make any adjustments not described in
the manual. Unplug the unit and contact a qualified service
technician.
2 IFREPLACEMENTPARTSAREREQUIRED
Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.
3HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacture’s service literature to ensure that the unit is
in safe operating condition.
Important Safeguards and Precautions
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL
ELECTRICAL CODE
2
OUTDOOR ANTENNAINSTALLATION
1 SAFEANTENNAANDCABLECONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded so
as to provide some protection against built up static charges
and voltage surges. Section
810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen to
fall. When installing an outside antenna, extreme care should be
taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage
within the unit may have sufficient magnitude to
cause electric shock.
Therefore, it is dangerous to make any kind of
contact with any inside part of this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this
unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
3
FCC Warning: Any unauthorized changes or modifications to this equipment would void
the user’s authority to operate.
Safety Precautions/Mesures de sécurité
WARNING: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
CAUTION: To prevent electric shock, match wide blade of plug
towideslot,fully insert.
Avertissement:Afin de prévenir tout risque d’incendie ou de
chocs électriques, ne pas exposer cet appareil à
la pluie ou à une humidité excessive.
Attention: Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante
de la prise et pousser jusqu’au fond.
RegionManagement Information:
This DECK is designed and manufactured to respond to
the Region Management Information that is recorded on
a DVD disc. If the Region number described on the DVD
disc does not correspond to the Region number of this
DECK, this DECK cannot play this disc.
The Region number
for this DECK is 1.
1
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO
OPERATE THE UNIT CORRECTLY INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOUR SELF, REFER
SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing uses only.
ATTENTION:
RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCCNOTE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize
an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the
booklet, “Something About Interference”available from FCC local regional offices helpful.
FCC Caution:
To assure continued compliance, (example- use only shielded interface cables when connecting to other
devices.) Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.

4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Congratulations
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the
information below. The serial number is on the
tag located on the back of your DECK.
Before Using
RF Coaxial
Cable
VJAS0196
Batteries 2 “AA”Remote Control
LSSQ0303
Accessories
Loading the Batteries
•Date of Purchase
•Dealer Purchased From
•Dealer Address
•Dealer Phone No.
•Model No. PV-D4761
•Serial No.
Battery replacement caution
•Do not mix old and new batteries.
•Do not mix alkaline with manganese
batteries.
1) Open cover.
3) Close cover.
2) Insert
batteries as
marked.
To order accessories, call toll free
1-800-332-5368.
If disc is brought from a cold to a warm
environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
•exposed to direct sunlight.
•that are humid or dusty.
•near heat (i.e. heater, radiator, etc.).
Disc Handling
Disc tray
Disc
To clean disc surface
With a soft, damp (water only) cloth, gently wipe
from the center hole to the outer edge as shown
below. (Wiping in a circular pattern will scratch the
surface.)
Handling precautions
•Only hold disc by edges as shown below.
Fingerprints, dirt and scratches can cause
skipping and distortion.
•Do not write on label side of disc.
•Never use record cleaning sprays, benzine,
thinner, static electricity prevention liquids,
or any other solvent.
•Be careful not to drop or bend disc.
•Do not place more than
1 disc on disc tray.
•Do not try to close disc
tray when disc is not
properly placed.
•Always store discs in
their proper cases
when not in use.
Disc formats supported by this DECK
DECK can play back discs bearing any of
the following marks:
Discs which cannot be played
•DVD with Region No. other than “1”or “ALL”
•DVD of PAL system •DVD-R/DVD-RAM
•DVD-ROM •CD-ROM
•CDV •CD-G •CD-RW
DVD
3”(8 cm) disc / 5”(12 cm) disc
Video CD
3”(8 cm) disc / 5”(12 cm) disc
CD
3”(8 cm) disc / 5”(12 cm) disc
is a registered trademark.
Do not try to play Photo CD or CD-R.

5
[email protected]
Table of Contents
Timer Recording..............................................................24, 25
Timer Recording Using VCR Plus+ System ...............26 ~ 29
MTS Broadcast/ VHS Hi-Fi Stereo System ....................30, 31
Multi-Brand Control Feature ...........................................32, 33
Tape Operation (Search System) .......................................34 ~ 36
Special VCR Features .....................................................37, 38
Copying Your Tapes (Dubbing) .........................................................39
Disc Operation ...............................................................40 ~ 44
DVD Operation using On-Screen Displays .................45 ~ 47
DVD Lock Feature .................................................................48
Settings for DVD Operation ..........................................49 ~ 51
Language Code List..............................................................52
DVD / VCR
Warning and Instruction Displays........................................53
Before Requesting Service.............................................54, 55
Service Center List ................................................................56
LimitedWarranty ...................................................................57
Spanish (Español) Quick Use Guide............................58 ~ 63
Index.......................................................................Back Cover
DVD / VCR
Important Safeguards and Precautions ............................ 2, 3
Before Using............................................................................4
DECK & Cassette Information........................................... 6 , 7
Location of Controls .......................................................8 ~ 10
Displays (On Screen Displays and Multi Function Display).....................11
Connections ..................................................................12 ~ 15
Initial Setup for Basic Connections ...............................16, 17
VCR
Reset Language, Channels, Clock, VCR’s Output Channel ...18, 19
Playback/ Record on a Tape...........................................20, 21
DVD
Basic DVD Operation ......................................................22, 23
Initial Setup
(Connection) Basic
Operation VCR
Operation For Your
Information
DVD
Operation

6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Video Head Clog Sensor
During playback, this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or DECK.
Playing older or damaged tapes may eventually
cause video heads to become clogged.
V I D EO HEADS M AY
N EED CLE A N I NG
PLEASE I NSERT HEAD
CLE A N I NG CASSE TT E
OR REFER T O MANUAL
END : P L AY
DECK & Cassette Information
•Use “dry”type head cleaning cassette
only. (PartNo.NV-TCL30PTisrecommended.)
•Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
•If head clog symptoms persist, contact your
nearest Factory Service Center or
authorized Service Center (see p. 56).
Head Cleaning
Only use tapes with the mark in this DECK.
Prevent Accidental Tape Erasure
Record/ Playback Time
Record Tab
Cover the hole
with cellophane tape.
Torecordagain
Break off the tab to
preventrecording.
SP
(Standard Play) 2 Hours
40 Minutes
1 Hour 2 Hours
5 Hours
20 Minutes
2 Hours 4 Hours
LP
(Long Play)
3 Hours 6 Hours 8 Hours
SLP
(SuperLongPlay)
Type of Video Cassette
Tape Speed
Setting T160T120T60
Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes
on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be
marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since
the materials used in the cabinet will accumulate more dust. We recommend using a nonabrasive,
antistatic cleaner and polisher.
Cleaning DECK
Digital Auto Picture
Automatically controls the video output signal for less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to reduce picture noise.
Press CH (TRACKING) /buttons on the remote control or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) /buttons operate as a V-Lock control.
Features for a Quality Picture (VCR)
R
R
R
R
R
R
R
R
Built-inHeadCleaner
A clean video head helps produce a clear
picture.
So, we have equipped your DECK with
a built-in, non-chemical head cleaning
system that helps prevent clogging of the
video heads. Cleaning is performed each
time you load or unload a video cassette.
•This feature is preventative only, If your
video heads are seriously clogged, consider
the use of a chemical non-abrasive head
cleaning kit or take your DECK to a Service
Center.
Screw driver

7
[email protected]
Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts
Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system
Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125
Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-VHS Output (DVD only), Component Video Output (DVD only)
Audio Output 2 (L), (R)
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 6.9 kg (15.2 lbs).
Dimensions: 430 (W) x 118 (H) x 364 (D) mm
16-15/16”(W) x 4-5/8”(H) x 14-5/16”(D)
Discs Played
(1) DVD-VIDEO Disc 5”(12 cm) single-sided single-layer
(one layer per side) 5”(12 cm) single-sided double-layer
5”(12 cm) double-sided double-layer
3”(8 cm) single-sided single-layer
3”(8 cm) single-sided double-layer
3”(8 cm) double-sided double-layer
(2) Compact Disc 5”(12 cm) disc
(CD-DA, VIDEO CD) 3”(8 cm) disc
Digital Audio Output: Digital Optical Connector
Pickup: Wave length: 655 nm (DVD), 790 nm (Video CD/CD)
Laser power: CLASS II
Specifications
Note: •Designs and specifications are subject to change without notice.
Definition of Terms (DVD)
Angle: Some DVD discs feature scenes simultaneously shot from different angles.
The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights up on DECK when a scene recorded at different
angles is detected.)
Chapter Number:Titles are subdivided into numbered sections.You can quickly search for
a favorite scene using these numbers.
DVD: A high-density optical disc on which high-quality pictures and sound have
been digitally recorded. DVD incorporates new video compression
technology (MPEG II) and high-density recording technology which allow
entire movies to be recorded with incredible playback quality.
Playback Control:With Video CD (version 2.0), scenes or information may be selected for
viewing or listening from an interactive menu that appears on the TV screen.
Subtitles: Written dialogue which appears at the bottom of the screen.
Time Number: The elapsed play time from the start of a disc or title. Use to quickly find
scenes. (May not work with some discs.)
Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks
to be quickly located.
Video CD: CD containing picture and sound with same quality level as video tape.
This DECK also supports Video CDs with playback control (version 2.0).
Initial Setup
(Connection)
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls
RemoteControl
ZOOM
p. 41
POWER
DSS/CABLE mode
p. 32
SPEED
p. 21
NUMBER keys
TV mode
p. 32
TAPEPOSITION
p. 38
EJECT/
OPEN/CLOSE
pp. 20, 22
ACTION
pp. 18 , 49
PAUSE /STILL
pp. 20, 23
COUNTER RESET
p. 36
PROGRAM/VCR+
p. 24
RECORD
p. 21
ADD/DELETE/ CLEAR
pp. 19, 43
VCR mode
p. 32
VOLUME + / -
p. 32
CHANNEL /
TRACKING/V-LOCK
pp. 21, 6
PLAY
pp. 20, 22
REWIND/ SEARCH /
SLOW-
pp. 20, 23
DVD mode
p. 32
INPUT
p. 39
COMMERCIAL SKIP/
ZERO SEARCH pp. 35, 36
DISPLAY
DISPLAY
LIGHT
STOP
pp. 20, 22
FAST FORWARD/ SEARCH /
SLOW+
pp. 20, 23
ANGLE
p. 41
SUB TITLE
p. 40
SURROUND/ ENTER
pp. 23, 32
MENU
p. 42
SET
VCR/TV
p. 21
RETURN / SEARCH
pp. 22, 34
TITLE
p. 42
Light button: When Light button is pressed, (DVD, TV, VCR, PLAY, STOP, REW, FF) buttons will
light up for 5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the battery.
EJECT button: When this button is pressed in VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
AUDIO (SAP/ Hi-Fi)
pp. 31, 40
SELECT
Bold:VCRFunction
Italic: DVD Function
Bold Italic: VCR and DVD Functions
Normal: Others
SKIP
SKIP
p. 23
DISPLAY
pp. 11, 45
LightTowerUniversalRemoteControl

9
[email protected]
Front View of DECK
Audio/Video
Input Connector 2
(LINE 2) p. 39
CHANNEL /
TRACKING/V-LOCK
pp. 21, 6
POWER
PAUSE
p. 23
OPEN/CLOSE
p. 22
VCR/TV
p. 21
STOP/EJECT
p. 20
Multi Function
Display
p. 11
For assistance, call 1-800-211-PANA(7262)
REC
p. 21
If the disc cannot be removed...
First, unplug DECK.Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.
Disc Tray
Over 2 inches
Cassette
Compartment
PLAY
p. 20
Remote
Sensor
FAST FORWARD/SEARCH
p. 20
REWIND/SEARCH
p. 20
Front View of DECK
Initial Setup
(Connection)
SKIP
SKIP
p. 23
PLAY
p. 22
STOP
p. 22
Bold:VCRFunction
Italic: DVD Function
Bold Italic: VCR and DVD Functions
Normal: Others

10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls (continued)
RearViewofDECK
AC Power Plug
S-Video Out
Connector
(DVD Only)
p. 13
Component
Video Output Connector
(Y, P B , P R ) p. 13
(DVD Only)
AudioOutput2
Connector (L/R)
p. 13
Optical Digital
Audio Output
Connector
(DVD Only)
p. 15
VideoInput
Connector
p. 39
VideoOutput
Connector
p. 12
AudioInput
Connector (L/R)
p. 39
AudioOutput1
Connector (L/R)
p. 12
VHF/UHF Antenna
InputTerminal
p. 12
VHF/UHF Antenna
OutputTerminal
p.12
DVD OUTPUT
DIGITAL
AUDIO OUT
(PCM/BITSTREAM)
OPTICAL
S-VIDEO OUT
SELECT
COMPONENT
VIDEO OUT
Y
P B
P R
L
R
VIDEO
AUDIO1
L
R
OUT IN1
IN FROM ANT.
OUTTOTV
VHF/UHF
OUT
AUDIO2
SEE MANUAL
•While plugged into an AC outlet,
this DECK consumes 4 W of
electrical power in off mode.
••
The following table shows the status of the output jacks when in VCR or DVD mode.
VideoOutput
AudioOut 1
AudioOut 2 Component
Video Output S-Video Out
VCR
DVD
YES
YES YES Switchable YES
N/A N/A
Bold:VCRFunction
Italic: DVD Function
Bold Italic: VCR and DVD Functions
Note •ACTION and PROG/VCR+ buttons on the remote are not available when using
Component Video Output and S-Video Out.
Please set TV to either RF INPUT or VIDEO INPUT, and then press ACTION or
PROG/VCR+.

11
[email protected]
REC 1 2 : 0 0 A M
0 : 25
ABC
- 0 : 1 2 : 3 4
SP
S T ER EO
SAP
M ONO
VCR Status & Clock Display
Blank Tape/ No Video Signal
Indication
Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 37) set to OFF, the TV
screen will turn solid blue.
Function Status
Rec Time Remaining
(OTR mode only,
see p. 21.)
0 8
Current Time Channel
Tape Speed
(See p. 6.)
Broadcast Audio
Being Received
(See p. 30.)
When a function button
is pressed, e.g. PLAY,
or you change channels,
a 4 second display
appears first in large and
then small characters.
Counter
Displays (On Screen & Multi Function)
To display or remove
overlay at right,
--> press DISPLAY.
A
M
VCR
VCR REC
DVD
ANGLE
VCR Hi-Fi TIMER
•
•
•
•
Hi-FiIndicator
Lights up when Hi-Fi audio
is monitored in Play mode.
VCR mode Indicator
Lights up when
DECK is VCR mode.
PowerIndicator
Lights up when power
is on.
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays VCR
status when a function button is pressed. Briefly
displays the channel number, or “L1”or “L2”when
a channel or line input is selected. Briefly displays
the recording speed when SPEED is pressed.
ANGLEIndicator
Lights up when a scene
recorded at different
angles is detected.
See p. 41. (DVD only).
DVD mode Indicator
Lights up when
DECK is DVD mode.
VCR REC Indicator
Lights up during
recording.
MultiFunctionDisplay
OnScreenDisplays(VCR)
VCR Indicator
Lights up when the
VCR/TV selector is
set to VCR.
Timer Indicator
Lights up when DECK is set for
Timer Recording, or when One
Touch Recording (OTR) is used.
Flashes when Timer Recording
is set, but a tape has not been
inserted into DECK and when
a power interruption occurs
during Timer Programming.
Initial Setup
(Connection)
AM
Lights before noon.
PM is not displayed.

12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections
1Disconnect antenna or cable from TV
and connect to DECK.
WARNING
When using “Nut type”RF coaxial cables, tighten with fingers
only. Overtightening may damage terminals.
BasicConnections
•Connect DECK and TV with an RF Coaxial Cable
a
(supplied) or an AV Cable b
(not supplied) as shown in the figure below.
•If your TV has AUDIO and VIDEO IN terminals, connect them to DECK with AV Cable
for higher quality picture and sound.
•You can enjoy stereo sound even if your TV is not stereo by connecting a stereo
amplifier to DECK.
IN FROM ANT.
OUT TO TV
AUDIO
IN1
OUT
DVD/VCRDECK
VHF/UHF
R
L
VIDEO VHF/
UHF
VIDEO
IN
AUDIO IN
RL
TV
AV CABLE (not supplied)
2Connect DECK to TV with RF Coaxial Cable.
RF COAXIAL CABLE
a
b
DSS
Receiver
OUT
IN
IN
Note to CABLE system installer
This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC
in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
OUT
IN
Antenna or Cable
CableBox
■ ■
■ ■
■ DECK TV
■ ■
■ ■
■ DSS Receiver DECK TV ■ ■
■ ■
■ Cable Box DECK TV
or

13
[email protected]
YouCannotYouCan
•record and view
bothscrambled
andunscrambled
channels if
additional
equipmentis
added.This
connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.
•viewchannel
other than the
one selected
for any type of
recording.
•doa Timer
recording of a
channel unless
you select it on
the Cable Box.
IN FROM ANT.
OUT TO TV
IN1
VHF/UHF
OUT
IN 2IN 1
Cable Box
OUTIN
OUT2
OUT1
2-Way Splitter
OUT
A/B Switch
IN
■■
■■
■ Connect With Two Cable Boxes
IN FROM ANT.
OUT TO TV
IN1
VHF/UHF
OUT
Cable Box
OUTIN
IN R
L
OUT
TV
VIDEO
AUDIO
■ ■
■ ■
■ DECK Cable Box TV
ANT or CATV
YouCannotYouCan
•record
scrambled
channels.
•view any
(including
scrambled)
channel.
•useRemote
Control to select
channels without
usingMulti-brand
control feature.
ANT
or
CATV
IN
VIDEO
AUDIO
R
L
OUT
TV
Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (Audio input for COMPONENT
or S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, set SELECT SW to COMPONENT VIDEO OUT.
If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, set SELECT
SW to S-VIDEO OUT.
When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.
ConnectionsForDVDOnly
OtherConnections
VIDEO
AUDIO
R
L
TV
COMPONENT
VIDEOOUT AUDIOOUT2
S-VIDEO OUT
SELECT
DVD OUTPUT
Y
P B
PR R
L
IN
Y
PB
PR
S-VIDEO
IN
R
L
IN
From DECK’s
A/V OUTPUT
1
2
3•You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,
and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only
from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.
•ACTION and PROG/VCR+ buttons on the remote are not available when using S-VIDEO OUT
and COMPONENT VIDEO OUTPUT. Please set TV to either RF INPUT or VIDEO INPUT, and
then press ACTION or PROG/VCR+.
Notes
Initial Setup
(Connection)
DVD/VCRDECK
DVD/VCRDECK
DVD/VCRDECK
or
IN
VHF/
UHF
Cable Box
Note •The picture will not be displayed if the SELECT SW is not set to the correct video output.
VHF/
UHF

14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections (continued)
Notes on Audio Output from the Optical Digital Audio Output Connector
Enjoying Digital Audio Output from the Digital Audio Output Connector
*1 The type of audio output from the connector can be selected by the Settings for DVD Operation.
(See p. 50.)
*2 Sound having 96 KHz sampling is converted into 48 KHz sampling when it is output
from the DECK’s optical digital audio output connector.
For Your Reference:
•Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing
Corporation.
Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables
a large quantity of sound data to be efficiently recorded on a disc.
•Linear PCM is a signal recording format used inCDs. While CDs are recorded in 44.1 KHz/16 bit,
DVDs are recorded in 48 KHz/16 bit up to 96 KHz/24 bit.
•If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from
the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with
the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound
Decoders please contact your local dealer.
AudioConnections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them
so that air can circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.
Disc
DVD
Video CD
CD
Sound recording format
Dolby Digital
Linear PCM
(48/96 KHz 16/20/24bit)
dts
MPEG 1
Linear PCM
Optical digital audio output from connector
Dolby Digital bitstream (1-5.1 ch)
or OFF (no output)*1
Linear PCM (2ch)
(48 KHz sampling/16 bit only)*2or no output*1
Bitstream or no output*1
PCM (44.1 KHz sampling)
Linear PCM (44.1 KHz sampling)
Speaker
■ DECK
Amplifier Speaker
Amplifier Speaker
AUDIO OUT2 AUDIO IN
R L
L
R
Manufactured under license from Dolby Laboratories.
“Dolby”and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
DVD/VCRDECK

15
[email protected]
■ DECK
Decoder with Dolby Digital Amplifier Speaker
or
dts (digital theater systems)
When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or
dts bitstream is output from the DECK optical digital audio output connector.When
DECK is connected to a Dolby Digital decoder or dts decoder, you can enjoy
theater-quality audio in your home. [An optical digital audio cable (optional) is
required when an optional Dolby Digital decoder or dts decoder is used.]
Notes on connecting an optical
digital audio cable (optional)
•Firmly connect the cable to the
connector.
Caution for Optical Digital Audio Output Connector:
•When connecting an amplifier (with an optical digital input connector) which does not
contain the Dolby Digital or dts decoder, be sure to select “OFF”at “Dolby Digital”and
“OFF”at “dts”of the Settings for DVD Operation “AUDIO OUTPUT”(see p. 50).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may
be harmful to your ears and damage your speakers.
•When a dts decoder is connected, please select “Bitstream”at “dts”of the Settings for
DVD Operation “AUDIO OUTPUT”.
If “OFF”is selected, there will be no sound. (See p. 50).
•Video CDs and CDs can be played as normal.
Note:
•Some dts decoders which do not support DVD-dts interface may not work properly with DECK.
Initial Setup
(Connection)
Amplifier
OPTICAL
DVD/VCRDECK Front
Speaker Front
Speaker
Surround
Speaker Surround Speaker
Center
Speaker
Subwoofer
Decorder with Dolby
Digital dts processing
(optional)
OpticalDigital
AudioCable
(optional)
To Optical
Digital Audio
Input Connector

16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before doing Initial Setup
How to do Initial Setup
Initial Setup for Basic Connections
1
2Press VCR button* on the remote for VCR mode.
Press POWER to turn DECK on.
•When DECK is turned on for the first time,
SELECT LANGUAGE screen appears.
•If wrong language is set, or there is not
Language Display, do “Reset All Memory
Functions”steps on p. 17.
•If screen does not appear, check connection
between DECK and TV.
•When you want to change the output channel of
DECK, please refer to VCR’s Output Channel
on p. 19.
3Press CH for English,
or
Press CH for Spanish,
or
Press VCR/TV for French,
to select language.
POWER
ACTION
CH /
VCR
VCR/TV
SELECT LANGUAGE
PRESS CH : EN G L I SH
O P R I M I R CH : E SPA ÑO L
APP.
VCR / TV : FRAN ÇA I S
T
O CHANGE VCR ’ S O UTPUT
CH,
PRESS ACT I ON KEY.
TurnTVon.
See connections
a
RF Coaxial Cable Connection and bAV Cable
Connection on p. 12.
<RF Coaxial Cable Connection>
Set TV to channel 3.
<AV Cable Connection>
Set TVto VIDEO.
[DECK-TV]
•Go to “How to do Initial Setup.”(See below.)
[Cable Box-DECK-TV], [DSS-DECK-TV]
•Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel
in your time zone.
•If you use DSS Receiver, it must be turned off.
SET
2
1
3
SELECT
4Press
to select.
Press SET.
•If you selected “CABLE/DSSBOX VCR TV”,
continue with step 5. If not, go to step 6.
SELE C T : SET : SET
EXIT
: ACT I O N
SELE C T CONNECTION
V
CR TV
C ABLE / D SS B O X V C R TV
V
CR CAB L E / D SS B O X TV

17
[email protected]
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Initial Setup
(Connection)
Press CH
to start “CHANNEL/CLOCK AUTO SET.”
6
Settings are performed automatically.
Case 1 Setup complete...
Press CH
to exit.
Case 2 Setup Incomplete...
Press ACTION
to display Manual
Clock Set screen.
7
Press
to select the month
and
press SET.
In the same manner,
select and set the
date, year, time, and
DST (daylight saving
time).
Press ACTION twice
to start CLOCK
and exit.
5Press
to select the same channel as the Cable
Box or DSS Receiver output channel.
Press SET to enter.
Use when moving DECK to new
location, or if a mistake was made in
the Initial Setup section.
•Make sure a tape is not inserted in
DECK.
ResetAllMemoryFunctions
Turn DECK
Power on.
2
1
3
Press and hold both PLAY and
CHANNEL on DECK for more
than 5 seconds.
•The power shuts off.
•Please ignore “NO CASSETTE”
warning.
Do “Initial Setup”on p. 16.
SELE C T : SET : SET
EXIT
: ACT I O N
SELE C T CONNECTION
C ABLE / D SS B OX OU TP U T CH
CH
CH
0
0
1
C ABLE / D SS B O X V C R TV
CH A NN EL / C L OCK AUT O SET
CONN E CT A NT E NN A CABLE
L OC A L PB S CH THE N . . .
AND I F Y OU US E A CABLE
B O X, TUNE I T TO Y OU R
P
L E A S E PRESS C H U P K E Y
1 / 4 / 20 01 THU 12 : 00P M
END : CH UP KEY
D S T : ON
SETT I N G : CH 02
AUTO CLOCK SET
C O M PLETED
AUTO CLOCK SET IS
I NC O M PLETE
PLEASE SET CLOCK BY
PRESSING
ACT I ON KEY
DST : O N
SE
SE
L E C T M O N TH
TH
1 / / :
SELE C T :
SET : SET
EXIT : ACT I O N
- - - - - - - - -- - - - - - - -- - - - - -
SET C L OC K
S ET : S ET BACK :
ST A RT : ACT I O N
D ST : ON
1 / 4 / 2001
2001
THU
THU
12
12
: 0 0 P M
SET
SET
CO
CO
M P L E T E D
- - - - - - - - -- - - - - - - -- - - - - -
SET C L OC K

18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SELECT :
EXIT : ACTION
SET : SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Clock
2) Press to select
“MANUAL,”and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET,”and
press SET. Press CH .)
4) Press ACTION twice to
start Clock and exit this
mode.
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
SEL. :
QUITTER : ACTION
REGLER:SET
MENU
REGLAGE DVD
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL
LANGUAGE/IDIOMA:FRANÇAIS
CA SORTIE : 3
ELEGIR :
SALIR : ACTION
FIJAR : SET
MENU
PREPARAR DVD
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA : 3
SELECT :
EXIT : ACTION
SET:SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Language
For Spanish
For English
For French
1) Press to select
language item, and
press SET repeatedly.
Reset Language, Channels, Clock VCR’s O
SELECT :
EXIT : ACTION
SET : SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Channels
2) Press to select
“ANTENNA,”then
press SET to set your
antenna system
(“TV”or “CABLE.”)
3) Press to select
“AUTO SET,”then
press SET.
•If you use Cable Box,
set it to the PBS channel
in your time zone.
4) Press CH .
1
2
Press ACTION*
to display MENU.
SELECT :
EXIT : ACTION
SET:SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
2) Press ACTION to exit.
SELECT :
EXIT : ACTION
SET:SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SELE C T : SET : SET
EXIT : ACT I O N
ANT
ANT
ENN
ENN
A : CABLE
A U T O S E T
W EA K S I GN AL D I SPLA Y : OFF
CABLE / DSS BOX SET UP
VCR P lus+ CH SET UP
C
ABLE / DSS B O X SET UP
V CR Plus + C H SET UP
SET UP CH A NNE L
CH A NN EL / C L OCK AUT O SET
CONN E CT A NT E NN A CABLE
L OC A L PB S CH THE N . . .
AND I F Y OU US E A CABLE
B O X, TUNE I T TO Y OU R
P
L E A S E PRESS C H U P K E Y
AUT O C L OC K SET
M A NU
NU
AL
AL
T I M E ZO N E A D JUS T : 0
SELE C T : SET : SET
EXIT : ACT I O N
SET C L OC K
D ST : ON
1 / 4 / 20012001 THUTHU 1212 : 0 0 P M
SELECTSELECT H OUROUR
- - - - - - - - -- - - - - - - -- - - - - -
SET C L OC K
SELE
C T :
SET : SET BACK :
EXIT : ACT I O N
1) Press to select
“SET UP CHANNEL,”
and press SET.
1) Press to select
“SET CLOCK,”and
press SET.
•ACTION and PROG/VCR+ buttons are
not available when using Component Video
Output and S-Video Out.
Please set TV to either RF INPUT or
VIDEO INPUT, and then press ACTION
or PROG/VCR+.
•After Channel Auto Set is
finished, Clock Auto Set
will be performed.
3) Press and to
select, then set the date,
time, and DST (Daylight
Saving Time).
(This screen appears only
when auto clock is set.)

19
[email protected]
Add or Delete a Channel
To add channel:
Select channel with NUMBER keys
and press ADD/DLT.
To delete channel:
Select channel with CH /or
NUMBER keys
and press ADD/DLT.
C HANNEL 08 ADDED
C HANNEL 08 DE L E T ED
Time Zone Adjust
2) Press to select
“TIME ZONE ADJUST,”
and press or to
subtract or add hour(s)
as necessary.
VCR’s Output
Channel
1) Press to select
“VCR’S OUTPUT CH.,”
and press SET.
SELECT :
EXIT : ACTION
SET : SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
2) Press ACTION.
After 3 seconds
SELECT :
EXIT : ACTION
SET : SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:4
•To Make Corrections,
repeat steps 1) ~ 2).
DST (Daylight Saving Time)
DECK auto adjusts clock for DST.
(p. 17.)
Spring (First Sunday in April)
DST:ON-->Setsclockaheadonehour.
Autumn (Last Sunday in October)
DST:ON -->Turns clock back one
hour.
•If your area does not observe
Daylight Saving Time, select
DST:OFF.
•Keep these time changes in mind
when programming DECK for
Timer Recording.
VCR’s Output Channel
1) Press to select
“SET CLOCK,”and
press SET.
*Important: If a remote control button does not work
when pressed, press the VCR button
on the remote and try the button again.
(Only when Auto Clock is set.) ADD/DLT
NUMBER
keys
POWER
ACTION
CH /
Basic
Operation
3) Press ACTION.
4) Press POWER off and
wait a maximum
10 minutes until Auto
Clock Set is performed
by DECK.
•“TIME ZONE ADJUST”
returns to “0”if clock is
set manually.
I F YOU PRESS ACT I O N
KEY, VCR’
S O UTPUT CH
S W I TCHES T O CH 4 .
PLEASE TUNE Y O UR TV TO
CH 4 .
SELE C T : SET :
EXIT : ACT I O N
SET C L OC K
AUT O C L OC K SET
M A NU AL
T I M E
E
ZO
ZO
N E A D JUS
JUS
T
T
: 0
0
SELECT :
EXIT : ACTION
SET : SET
MENU
SET UP DVD
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SET
SELECT

20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playback/ Record on aTape
Insert a tape.
•DECK power comes on.
The VCR mode and “VCR”Indicator light up
on Multi Function Display.
•If tape has no rec. tab (p. 6), auto play begins.
Special Features During Play
•These features work best in SP or SLP mode.
•The sound will be muted.
•To reduce picture noise, see “Manual Tracking
Control”on p. 6.
•After DECK is in Still or Slow mode for 3 minutes,
it will switch to Stop mode automatically to protect
the tape and the video head.
1
2
3
Notes
PAUSE/
STILL
REW/SLOW-
STOP
FF/SLOW+
EJECT
Insert a tape.
21
Playback using DECK buttons
Press PLAY.
Press REW/SLOW- or FF/SLOW+ in Stop
mode to rewind or fast forward a tape.
•Rewind tapes in approximately one minute
when using a T-120 tape.
Press EJECT on remote,
or STOP/EJECT on DECK to eject a tape.
Press STOP to stop a tape.
Press PLAY* to play a tape.
CH /
SPEED
REC
VCR/TV
PLAY
Multi Function Display
Press STOP/EJECT to stop
and/ or eject a tape.
Forward/Reverse Scene Search
--> Press FF/SLOW+ or REW/SLOW-.
--> Press again or PLAY to release.
Still (Freeze) Picture
--> Press PAUSE/STILL.
--> Press PLAY to release.
Frame by Frame Picture
--> Press PAUSE/STILL in Still mode.
--> Press PLAY to release.
Slow Motion Picture
--> Press FF/SLOW+ (increase speed) or
REW/SLOW- (decrease speed) in Still mode.
--> Press PLAY to release.
Playback a Tape
Ready Checklist
All connections are made (pp. 12 ~ 15).
TV and DECK are plugged in.
TV is on and tuned to CH3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR.)
DVD
Rapid Rewind/FF