Panasonic EH-ND21 User manual

© Panasonic Electric Works (Thailand) Co., Ltd.
2010. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PEWT1011T07CE
Hair Dryer
Model No. EH-ND21
TAIWAN
TABLE OF CONTENTS
PAGE PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------11
6 Schematic Diagram ---------------------------------------------12
7 Exploded View and Replacement Parts List -----------13

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
Refer to WIRING CONNECTION DIAGRAM.

4
4 Disassembly and Assembly Instructions
4.1. Disassembly instruction
1. Take off Nozzle AB Block as same direction in figure 4.
2. Remove a Tapping screw by Plus Driver and 2 Torx screws by IEC driver as figure 5.
3. Take off a Handle A as same direction in figure 6.

5
4. Take off an Air outlet grill and an Air outlet ring from Main body by rotating as figure 7.
5. Take off a Housing A ,a Discharge cover and a Design cover from Housing B as figure 8,9.

6
6. Take off a Motor heater block from Housing B as figure 10.
7. Take off an Air inlet grill from a Motor heater block as figure 11.

7
4.2. Assembly instruction
1. Install Lead wires with Main switch and Capacitor as figure 12.
2. Connecting and soldering Motor heater block with Main switch as figure 13.

8
3. Assemble a Motor heater block with a Housing B as figure 14.
4. Assemble a Design cover with a Housing B as figure 15.

9
5. Assemble Motor heater block with Handle B and Housing B as figure 16.

10
6. Assembly handle A , screw and nozzle A,B as shown figure 17.

11
5 Wiring Connection Diagram

12
6 Schematic Diagram

Model No. : EH-ND21 Exploded View
7 Exploded View and Replacement Parts List

Model No. : EH-ND21 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 EHND21T0312W TORX SCREW 3.0*12 2 *1
2 EHND21HDW1W HANDLE AB 1
3 EHND21CRTW CLICK RING 1
4 EHND21SRTW SWIVEL RING 1
5 EHND21T2004W TAPPING SCREW 2.0*4 1
6 EHND21HSW1W HOUSING AB 1
7 EHND21DSCPW DESIGN COVER 1
8 EHND21NZPW NOZZLE AB BLOCK 1
9 EHND21AORW AIR OUTLET RING 1
10 EHND21AOGW AIR OUTLET GRILL 1
11 EHND21MHA2W MOTOR HEATER BLOCK 1 A2-PLUG (WITH 5 INSULATION TUBES)
12 EHND21AIGHW AIR INLET GRILL 1
13 EHND21MSPWW MAIN SWITCH PLATE 1
14 EHND21MS2W MAIN SWITCH 1 (WITH CAPACITOR, 5 INSULATION TUBES)
- EHND2113503W INSTRUCTION BOOKLET 1
- EHND2113501W INDIVIDUAL PACKAGE 1