Panasonic EH-NE83 User manual

Order Number PEWT1710A28CE
(Household) Hair Dryer
Model No.
EH-NE83
Asia
Middle East
TABLE OF CONTENTS PAGE
1 Warning ---------------------------------------------------------------------------------------
2
2 Specifications ------------------------------------------------------------------------------- 2
2
3 Troubleshooting Guide ------------------------------------------------------------------------ 3
3
4 Disassembly and Assembly Instructions -------------------------------------------- 5
5
5 Wiring Connection Diagram------------------------------------------------------ 12
12
6 Schematic Diagram ---------------------------------------------------------------- 15
13
7 Exploded View & Replacement Parts List ----------------------------------- 16
15
© Panasonic Corporation 2013 Unauthorized copying
and distribution is a violation of law.

1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder; Typical the melting point is 50 - 70°F (30 - 40℃) higher.
Please use soldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10 ℃).
In case of using high temperature soldering iron, please becareful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).
Power source
Power consumption
(" II - Hot ")
Air volume without nozzle
Air temperature without nozzle
(" II - Hot ")
Dimensions
Cord length
Weight
Supplied accessory
90 K (in case of room temperature 30°C)
(W) 90mm x (D) 220mm. x (H) 270mm.
(without power cord and nozzle)
2. Specifications
AC 220-240 V , 50~60 Hz
Code L / 605 / 615 / 655 / 685 = 1.7 m
Approx. =530g.
Set nozzle
AC 220 V, 50~60 Hz, 2100 W
AC 230 V, 50~60 Hz, 2300 W
AC 240 V, 50~60 Hz, 2500 W
1.9 m3/min

3. TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
< TROUBLE >
< CHECK >
< REMEDY >
OK
<CHECK MOTOR HEATER ASSEMBLY>
Check if there are odd objects between
joints of thermo switch or not
(Figure 3)
Remove the odd objects
between joints
Found odd object
No odd objects
Replace the
MOTOR HEATER ASSEMBLY
Figure 3
Thermo Switch
Hot air is not emitted
<CHECK COOL SWITCH BUTTON>
Check the conductivity between the terminal 1
and 2 by push and hold
the COOL SWITCH BUTTON
(Figure 2)
<CHECK TEMPERATURE SWITCH>
Check the conductivity between the terminal 2
and 4 by setting
the TEMPERATURE SWITCH to Position 2
(Figure 1)
Replace the
MAIN SWITCH
NG
OK
Replace the
COOL SWITCH BUTTON
NG
COOL SWITCH BUTTON
Lead Wire (Orange)
Lead Wire (Blue and Red)
For EH-NE81-84 only
Figure 2
Figure 1
Lead Wire (Black)
Lead Wire (Brown)
Lead Wire (Orange)
Temperature Switch
OK

3. TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
< TROUBLE >
< CHECK >
< REMEDY >
Main body is
not operated
<CHECK POWER CORD>
Check the conductivity of power cord
<CHECK MAIN SWITCH>
Check the conductivity between the terminal 1
and 4 by setting
the MAIN SWITCH to Position 1
(Figure 4)
Replace the
MAIN SWITCH
Replace the
MOTOR HEATER
ASSEMBLY
NG
OK
NG
OK
Replace the
MOTOR HEATER
ASSEMBLY
Lead Wire (Yellow)
Lead Wire (Red)
Lead Wire (Gray)
Lead Wire (Orange)
*For code : 605, 655, 685, 695, 865
MAIN SWITCH
Figure 4

4. Disassembly and Assembly Instructions
4.1. Disassembly Instructions
1. Remove the FILTER FRAME ASSEMBLY 4. Remove TAPPING SCREWS by a cross
slot screw driver.Than take out AIR OUTLET RING
and AIR OUTLET GRILL by rotating follow the direction
below.
2. Remove 3 TAPPING SCREWS by a cross
slot screw driver,then Remove AIR INLET RING.
5. Take off HOUSING AB follow the figure below.
3. Remove 2 TAPPING SCREWS at HOUSING A
by flat-blade screwdriver and 2 TORX SCREWS
at HANDLE by Driver then remove HANDLE AB.
6. Remove DISCHARGE COVER
Counter clockwise rotation

4. Disassembly and Assembly Instructions
4.1. Disassembly Instructions
7. remove Ion Holder from DISCHARGE COVER as figure below.
8. Take off MOTOR HEATER ASSEMBLY, and PLATE SPRING from HOUSING B.
Unclip this 2 ribs

4.2 Assembly Instructions
1. High voltage lead wire for Ion discharge must be fixing with Ribs from Heater holder as below picture.

2. Install MAIN SWITCH PLATE AB and MAIN SWITCH HOLDER.
3. Install Ion discharge in to DISCHARGE COVER.
Ribs of MAIN SWITCH
HOLDER must fully
lock with MAIN SWITCH
(2 Ribs)

4. Assemble MOTOR HEATER ASSEMBLY, COOL SWITCH PLATE and PLATE SRPING into HOUSING B.
Lead wire to Heater block
assembly
must not on this area
Position of component must be as below
(EH-NE81,82,83,84 only)

5. Assemble DISCHARGE COVER / DESIGN COVER into HOUSING B.
6. Assemble HOUSING A, then tightening 2 TORX SCREWS.
7. Assemble AIR INLET RING and 3 TAPPING SCREWS.
TAPPING SCREWS 2.6*10
TORX SCREWS 3.0*12