Panasonic Toughbook CF-19KHRAG2M Wiring diagram

Supplementary Instructions
for Fingerprint Reader
NOTE: Useful and helpful information.
CAUTION: Condition that may result in minor or moderate injury.
[start] - [Run]: Click [start], and then click [Run].
You may need to double-click in some cases.
Î:Page in these Supplementary Instructions or in the Reference
Manual for the computer.
Some of the illustrations in this manual may differ slightly in shape from the
actual items in order to make the explanation easier to understand.
Terms and illustrations in this Manual
Contents
Names and Function of Parts ..................................... 2
Overview ....................................................................... 4
Installation.................................................................... 6
More Advanced Security ........................................... 9
Useful Information ....................................................10
Troubleshooting .......................................................14
Specifications............................................Back cover
Personal Computer
Model No. CF-19 / CF-30 Series

2
Names and Functions of Parts
Except the following, refer to the Operating Instructions for the computer.
<CF-19 Series>
(Appearance may differ, depending on specifications.)
<CF-30 Series>
(Appearance may differ, depending on specifications.)
Fingerprint Reader
Fingerprint Reader

3
This section explains how your fingerprints are enrolled and authenticated.
1Slide your finger to the right or
left.
To prevent a reading error.
ASet the first joint of your finger on the
sensor as illustrated to the right.
BSlide your finger to the right or left while
keeping it in contact with the finger-
print sensor.
CSlide your finger to the right or left until
the sensor is visible.
When the fingerprint sensor does not
enroll or authenticate your finger-
print properly:
· You slid your finger too fast or too slow.
· Your finger was soiled or it has a scar on the surface.
· Your finger was wet or extremely dry.
· Your fingerprint does not have sufficient data for personal identification.
For further information, refer to “Troubleshooting (For Devices)”. (Îpage 14)
How to Use the Fingerprint Reader
CAUTION
To protect the fingerprint sensor, be sure to close the cover when not
using the fingerprint reader.
We shall not be liable for any loss or damage whatsoever resulting from
your Fingerprint device or neglect of Fingerprint device use, or any data
loss resulting from such developments as Fingerprint authentication
device malfunctioning.
Fingerprint sensor
or
Fingerprint sensor

4
Fingerprint’s Outline
The conventional security systems use ID/passwords and token devices such as IC
cards to authenticate users. Therefore the passwords and token devices are ex-
posed to the risk of being lost, stolen and hacking.
The Fingerprint authentication method uses user’s fingerprints instead of passwords
for security authentication. You can use your fingerprints to start up your computer
and log on Windows.
We recommend you use the Fingerprint Reader in combination with the TPM (Trusted
Platform Module) to increase the security level of your computer.
Precautions
Security Functions
Fingerprint Authentication Technology does not guarantee complete authentication and
individual identification. Please acknowledge we shall not be liable for any loss or dam-
age whatsoever resulting from the use of, or inability to use your Fingerprint device.
The Fingerprint authentication method uses multiple fingerprints, encryption keys,
credentials data and passwords. You might not be able to use your data if you
lose fingerprints, keys, credentials and passwords, so keep them in a safe place.
For further information, refer to “Backup”. (Îpage 10)
General interaction with third-party applications: There is no guarantee
that there will not be any negative interaction with any third-party software,
and will not accept any responsibility for such an interaction.
Overview
Performed by the Computer Administrator Performed by each user
Step 4
User Fingerprint Enrollment
User’s Data
• Windows Logon Password
• Fingerprint
• Fingerprint Backup Password
• Power-on Password
Step 1
TPM Installation (“Installation Manual of TPM”)
(If the TPM is not being used, skip this step.)
(If the TPM is not being used, skip this step.)
Step 2
Fingerprint Utility Installation
Step 3
TPM Fingerprint Utility Initialization
This manual describes Steps 2, 3 and the initial part of Step 4.
For further steps, refer to the UPEK Protector Suite QL Help menu. (Click [start] - [All
Programs] - [Protector Suite QL] - [Help].)
Recommended Installation Procedure

5
You cannot use this function at the same time as the SD security function
is being used. When SD security is set, disable SD security function in the
following order before initial setting of fingerprint authentication.
ALog on to Windows as an Administrator.
BClick [start] - [All Programs] - [Panasonic] - [SD Card Setup].
CAdd a check mark for [Use the SD card when starting the computer].
DClick [OK].
· Follow the on-screen instructions.
· SD security is disabled and all registered SD memory cards become unavail-
able when your computer starts up.

6
Installation
Step1 TPM Installation
Refer to on-screen manuals “Installation Manual Trusted Platform Module (TPM)”.
(Click [start] - [Run], enter [C:\util\drivers\tpm\README.pdf], and click [OK].)
If the TPM is not being used, skip this step.
Step2 Fingerprint Utility Installation
Performed by the Computer Administrator.
1Log on to Windows as an Administrator.
2Close all other programs.
3Click [start] - [Run], enter [C:\util\drivers\fngprint\psql\
setup.exe], and click [OK].
The “Protector Suite QL ∗.∗Setup” screen appears.
4Click [Next].
Installation starts. Carefully read the License Agreement, select “I accept the
license agreement”, and click [Next]. Follow the on-screen instructions.
5When the “Protector Suite ∗∗
∗∗
∗.∗∗
∗∗
∗has been successfully installed.”
message appears, click [Finish] - [OK].
The computer restarts.
6Log on to Windows as an Administrator.
The “Protector Suite QL Icon” appears in the notification area.
Step 3 TPM Fingerprint Utility Initialization
Performed by the Computer Administrator.
The “Invalid TPM status” message is displayed by the “Protector Suite QL Icon”
in the notification area.
If the TPM is not being used, skip this step.
Preparation
[Only CF-19 series with Windows XP Tablet PC Edition]
Move Tablet PC Input Panel from upper right to the bottom right or bottom left .
If this procedure is skipped, the “Please swipe you finger” message may overlap
the Tablet PC Input Panel.

7
Step 4 User Fingerprint Enrollment
Performed by each user.
1Click [start] - [All Programs] - [Protector Suite QL] - [User En-
rollment].
The “Welcome” message appears, read the description carefully.
2Click [Next].
3Select an enrollment mode, and click [Finish].
Enrollment mode
You can make the configuration for the enrollment only once during this initializa-
tion phase.
· Enrollment to the biometric device
All enrolled fingerprints are stored directly in the fingerprint sensor. The user
data will be secured by the hardware protection keys obtained by the fingerprint
sensor. This mode allows up to 21 fingerprints to be enrolled.
· Enrollment to the hard disk
All enrolled fingerprints are stored on the hard disk. Hardware protection of the
user data is not possible, but multiple users can enroll their fingerprints.
When the “Finish” screen appears, read the description carefully.
“User Enrollment” wizard starts. Follow the on-screen instructions.
If the “Invalid TPM status” message is not displayed, click [start] - [All Programs]
- [Protector Suite QL] - [Control Center] - [Settings] - [System Settings] - [TPM]
- [Initialized TPM].
NOTE
Enroll at least two fingers. Even if one of them is injured, you can use
another one to access your account and secret data. For further informa-
tion about the enrollment, refer to “How to Use the Fingerprint Reader”
(Îpage 3) and “Fingerprint Tutorial”. (Click [start] - [All Programs] - [Pro-
tector Suite QL] - [Fingerprint Tutorial].)
NOTE
1Click on the “Invalid TPM status” message to start “Advanced
Security Initialization Wizard”.
Follow the on-screen instructions.

8
The number of fingerprints for “Power-on Security” is maximum of 21, be-
cause they are stored in the fingerprint sensor regardless of the selected
enrollment mode.
NOTE
We recommend you use the Power-on Security feature. This feature pre-
vents unauthorized access to the user’s computer at the BIOS level.
After first finger enrollment, “Power-on Security” message appears. Select [Yes].
AWhen the “Power-on Security” screen appears, click [Manage Passwords...].
BSelect [Power-On] in [Password Types], and click [Set password...].
CEnter the password for “Power-on Security”, and click [OK].
DClick [Close].
EAdd a check mark for [Power-On] in [Password Types].
FEnter the password (step C), and click [OK].
GClick [Next].
· Follow the on-screen instructions.
Installation

9
1Register the Supervisor Password.
You have to register the Supervisor Password to proceed to the next step.
If you have already registered the Supervisor Password, you can skip this
step, and move on to step 2.
If you have not done this, have enrolled your fingerprint using Protector Suite
QL, and have already made Power-on Security effective, after step B, your
fingerprint authentication will be necessary.
ATurn on or restart the computer.
BPress F2 several times while [Panasonic] boot screen is displayed soon after
the computer starts the startup procedure.
CSelect the [Security] menu.
DSelect [Set Supervisor Password], and press Enter .
EEnter your password in the [Enter New Password], and press Enter .
· The password will not be displayed on the screen.
· You can use up to 32 alphanumeric characters (including spaces).
· The case (upper/lower) is ignored.
· To input numbers for the password, use the numbered keys on the keyboard.
· You cannot use Shift and Ctrl to input a password.
FEnter your password again in [Confirm New Password], and press Enter .
GIn [Setup Notice], press Enter .
2Set the High Security Level.
ASelect [Fingerprint Security Sub-Menu], and press Enter .
BSelect [Security mode:], and select [High].
· Default setting: Simple
CPress ESC to close the sub-menu.
DPress F10 , select [Yes], and press Enter to exit the Setup Utility.
In the “High” security mode, you have to enter the Supervisor or User
Password even after fingerprint authentication.
In the “Simple” security mode, you do not have to enter the Supervisor or
User password after fingerprint authentication.
NOTE
More Advanced Security
You can increase your computer’s security level by setting the BIOS level described
in this section.
Performed by the Computer Administrator.

10
Useful Information
The file described below is necessary for recovering the Fingerprint authentication
data. Back up this file periodically in a safe location such as removable disk to avoid
data loss resulting from some accidents. We recommend you to store the file in a
removable disk or network drive because the benefit of Fingerprint authentication
security can be reduced if you keep the file in the internal hard disk drive.
The backup password described below is necessary for bypassing the Fingerprint
authentication. We recommend you set the backup password using the “User En-
rollment” wizard. If you do not define the backup password, you may lose your data
in case of authentication hardware failure.
File used by each user
· Backup user passport data
(Default name: <UserAccount>.vtp)
You need this file when you replace the embedded fingerprint chip, or the hard disk
drive, or when reinstalling Windows.
This file contains the fingerprints, encryption keys, and logon authentication data.
Password used by each user
· Backup Password for Enrollment
This backup password can be used in case of hardware failure to bypass the finger-
print authentication.
CAUTION
The passwords other than those explained above are also used for security,
so do not lose them. For further information, refer to the UPEK Protector Suite
QL Help menu (Click [start] - [All Programs] - [Protector Suite QL] - [Help]).
How to Backup:
Select “Export” in “Import or Export User Data” to save the user data. (Click [start]
- [All Programs] - [Protector Suite QL] - [Control Center] - [Fingerprints])
For further information, refer to the UPEK Protector Suite QL Help menu. (Click
[start] - [All Programs] - [Protector Suite QL] - [Help])
NOTE
Backup