Panasonic TH-65PB1W User manual

Model No.
TH-65PB1W
Operating Instructions
Interactive Plasma Display
For more detailed instructions, refer to the Operating
Instructions on the DVD-ROM.
Contents
•Important Safety Notice .............................2
•Safety Precautions.....................................3
•Accessories..............................................10
•Connections .............................................12
•Power On / Off .........................................15
•Basic Controls..........................................17
•Specications...........................................19
Please read these instructions before operating your set
and retain them for future reference.
TQB4TC0325
English

2
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
• HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
• “RealD 3D” is a trademark of RealD.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
Important Safety Notice
WARNING
1) To prevent damage which may result in re or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water (ower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked ame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only t an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic elds.
Using this appliance near sources of strong electromagnetic elds or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic elds.
IMPORTANT INFORMATION
If a display is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many
injuries, particularly to children, can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the display.
• Only using furniture that can safely support the display.
• Ensuring the display is not overhanging the edge of the supporting furniture.
• Not placing the display on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture
and the display to a suitable support.
• Not standing the displays on cloth or other materials placed between the display and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the display or its controls.

3
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
Always be sure to ask a qualied technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does
not hang over the edge of the base.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result
in re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic
dealer.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or downward may cause damage to the internal
circuitry.
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For sufcient ventilation;
If using the pedestal (optional accessory), leave a space of 10 cm or more at the top, left and right, and 7 cm
or more at the rear, and also keep the space between the bottom of the display and the oor surface.
If using some other setting-up method, follow the manual of it. (If there is no specic indication of installation
dimension in the installation manual, leave a space of 10 cm or more at the top, bottom, left and right, and 7 cm
or more at the rear.)
When installing the Plasma Display vertically;
Turn up the power switch for the upward direction when you install the Plasma Display vertically.
And set “Display orientation” to “Portrait” in Setup menu.
• Pedestal ......................................................................... TY-ST65P20
• Mobile stand for Display................................................. TY-ST65PF1
• Wall-hanging bracket (angled) ....................................... TY-WK65PR20
• BNC Dual Video Terminal Board.................................... TY-FB9BD
• HD-SDI Terminal Board.................................................. TY-FB9HD
• HD-SDI Terminal Board with audio ................................ TY-FB10HD
• Dual Link HD-SDI Terminal Board.................................. TY-FB11DHD
• Dual HDMI Terminal Board ............................................ TY-FB10HMD
• DVI-D Terminal Board .................................................... TY-FB11DD
• AV Terminal Box ............................................................. TY-TB10AV
• 3D IR TRANSMITTER ................................................... TY-3D30TRW
• 3D Eyewear.................................................................... TY-EW3D3SW, TY-EW3D3MW, TY-EW3D3LW
• Electronic Pen for Interactive Plasma Display ............... TY-TPEN1PBW
• Wireless Module............................................................. ET-WM200E

4
Safety Precautions
When using the Plasma Display
The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat, which can cause re or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
• Do not insert any metal or ammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause re or electric shock.
Do not remove the cover or modify it in any way.
• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.
Do not use any power supply cord other than that provided with this unit.
• Doing so may cause re or electric shocks.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause re. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.
• Do not damage the cable, make any modications to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause re and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, re or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
•
A short circuit may occur, which could cause re. Contact your local Panasonic dealer for any repairs that need to be made.

5
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and re or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
• Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in re.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
Do not burn or breakup batteries.
• Batteries must not be exposed to excessive heat such as sunshine, re or the like.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or reected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.

6
Safety Precautions
WARNING
Small Parts
3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small
children to avoid accidental ingestion.
Disassembly
Do not disassemble or modify the 3D Eyewear.
CAUTION
To enjoy 3D images safely and comfortably, please read these instructions fully.
Use for commercial applications and public viewing
Someone in authority should responsibly convey the precautions for use of the 3D Eyewear to the user.
3D Eyewear (sold separately)
Do not drop, exert pressure on, or step on the 3D Eyewear.
Be careful of the tips of the frame when putting on the 3D Eyewear.
Be careful not to trap a nger in the hinge section of the 3D Eyewear.
Pay special attention when children are using the 3D Eyewear.
3D Eyewear should not be used by children younger than 5 - 6 years old, as a guideline.
All children must be fully supervised by parents or guardians who must ensure their safety and health
throughout the using 3D Eyewear.
3D Safety Precautions

7
Safety Precautions
Viewing 3D Content
Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc.
When preparing your own 3D content, ensure that it is properly produced.
Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other
existing medical conditions.
Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other
uncomfortable sensation.
Take an appropriate break after viewing a 3D movie.
Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games
or computers.
Be careful not to strike the screen or other people unintentionally. When using the 3D Eyewear the distance
between the user and screen can be misjudged.
The 3D Eyewear must only be worn when viewing 3D content.
If you do not look toward the screen for a while when viewing 3D images, the 3D Eyewear may be turned off
automatically.
If you suffer from any eyesight problems (short / far-sighted, astigmatism, eyesight differences in left and
right), please ensure to correct your vision before using the 3D Eyewear.
Stop using the 3D Eyewear if you can clearly see double images when viewing 3D content.
Do not use the 3D Eyewear at a distance less than the recommended distance.
View from at least the recommended distance (3 times the effective height of the screen).
Recommended distance: 2.4 m
When the top and bottom area of the screen is blackened, such as movies, view the screen at a distance
3 times further than the height of the actual image. (That makes the distance closer than above recommended
gure.)
3D Eyewear (sold separately) Use
Before using the 3D Eyewear, ensure no breakable objects surrounding the user to avoid any accidental
damage or injury.
Remove the 3D Eyewear before moving around to avoid falling or accidental injury.
Use the 3D Eyewear only for the intended purpose and nothing else.
Do not use 3D Eyewear in the condition of high temperature.
Do not use if the 3D Eyewear is physically damaged.
Do not use any devices that emit the infrared signals near the 3D Eyewear, as this may cause the 3D Eyewear
false operations.
Do not use devices (such as mobile phones or personal transceivers) that emit strong electromagnetic waves
near the 3D Eyewear as this may cause the 3D Eyewear to malfunction.
Stop using the 3D Eyewear immediately if a malfunction or fault occurs.
Stop using the 3D Eyewear immediately if you experience any redness, pain, or skin irritation around the nose
or temples.
In rare cases, the materials used in the 3D Eyewear may cause an allergic reaction.

8
Safety Precautions
Electronic Pen Use
WARNING
Operating Safeguards
Do not alter the unit or modify any parts. Alteration or
modication can cause re or electric shock.
Choking Hazard
Keep the penpoint, electronic pen adapter and battery
out of reach of children to prevent swallowing.
Battery
Use only the specied type of battery. Using the
incorrect type of battery can result in overheating/
burning or leakage of battery acid.
Make sure that the battery is installed with the correct
polarity as indicated on the battery holder. Incorrectly
installed batteries may burst or leak, resulting in injuries.
Do not use the damaged batteries. Using damaged
batteries may result in leaking.
Do not short, heat, break or throw in a re, as it may
result in the battery leaking, generating heat, or
bursting.
When disposing of the battery, cover the battery
contacts with insulation (ex. tape). Direct contact with
other batteries may result in leaking, re, or explosion.
Do not solder the battery, as it may result in the battery
leaking, generating heat, or bursting.
Remove empty batteries immediately to avoid battery
uid leakage.
Avoid contact of battery uid with eyes, skin or clothing,
as this may result in irritation or injury. In these cases,
do not rub the affected area, and rinse thoroughly with
clean water.
Electronic Pen
Do not use near medical equipment.
(Do not bring into a surgery room, intensive care unit,
critical care unit, etc.)
Electromagnetic waves generated by this device
can affect equipment, and can cause equipment to
malfunction.
Do not use near automatic doors, smoke detectors and
other automatically controlled equipment.
Electromagnetic waves generated by this device
can affect equipment, and can cause equipment to
malfunction.
Use at least 22 cm away from pacemakers.
Electromagnetic waves generated by this device can
affect the operation of pacemakers.
CAUTION
When the unit is not used over an extended period of
time, take the batteries out of the unit. Otherwise, the
batteries may leak. Do not use the leaked batteries.

9
Safety Precautions
Precautions
Any changes or modications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate this device.
About Using the Battery
If a battery is used improperly, the battery may leak,
causing corrosion of the unit, or it may burst. To prevent
this, always follow the precaution given below.
• If the electronic pen ceases to function because
the battery has run out, remove it immediately and
dispose of it according to local regulations. Leaving
a drained battery in the electronic pen may result in
leakage.
Other Information
Usage Note
Operating the electronic pen and the electronic
pen adapter near electrical appliances may
cause interference. Move away from the electrical
appliances such as TVs, radios, cordless phone, or
wireless devices.
MEDICAL
Consult the manufacturer of any personal medical
devices, such as pacemakers, to determine if
they are adequately shielded from external RF
(radio frequency) energy. (The unit operates in the
frequency range of 2.405 GHz to 2.480 GHz, and
the power output level is 1 milliwatts.) Do not use
the unit in health care facilities if any regulations
posted in the area instruct you not to do so.
Hospitals or health care facilities may be using
equipment that could be sensitive to external RF
(radio frequency) energy.
No responsibility will be taken by our company with
respect to consequences resulting from the use,
damage or both of the equipment.

10
Accessories Supply
Accessories
Power supply cord Clamper × 1
TMME289
• elite Panaboard software
• elite Panaboard book
• Operating Instructions
Display Operations
Network Operations
Electronic Pen Operations
• Software license statements
GNU GENERAL PUBLIC LICENSE
GNU LESSER GENERAL PUBLIC LICENSE
Ferrite core × 2
J0KG00000014
Batteries for the Remote
Control Transmitter
(R6 Size × 2)
Remote Control
Transmitter
N2QAYB000691
Operating
Instruction book
Check that you have the accessories and items shown
Use the Ferrite cores to comply with the EMC standard.
(See page 14)
Software DVD-ROM × 1
Electronic Pen set
Recharger Cable × 2
2m
Electronic Pen × 2
Electronic Pen Adapter × 1
Pen Tip (Replacement) × 2
Rechargeable AAA Ni-MH
Battery × 2
Pen Holder × 2
 Store the extra pen tip along with this operating instructions.
About Using the DVD-ROM
To prevent damage to the DVD-ROM:
• Do not touch or write on the surface of the disc.
• Do not leave the disc out of the protective case.
• Do not leave the disc in the direct sunlight or near heat sources.
• Do not place heavy objects on the disc case or drop the case.
• To clean the disc, hold the disc by its edges and wipe it from the center to the edges with a dry, soft cloth.
N2FZ00000008 TKKL5543
N5EDZ0000006 • The supplied rechargeable battery
is only for this electronic pen. When
replacing the rechargeable battery,
replace it with a commercially available
rechargeable AAA Ni- MH battery.
(HHR-4MVT)
K1HY05YY0046
TKKA5002

11
+
-
+
-
Remote Control Batteries
Requires two R6 batteries.
1. Pull and hold the hook, then open
the battery cover.
2. Insert batteries - note correct
polarity ( + and -).
3. Replace the cover.
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5.
Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
6. Do not burn or breakup batteries.
7. Batteries must not be exposed to excessive heat such as sunshine, re or the like.
“R6” size
Accessories

12
Connections
Speaker connection
1 2
Using the clamper
Secure any excess cables with clamper as required.
Note:
One clamper is supplied with this unit. In case of securing cables at three positions, please purchase it separately.
AC cord connection and xing, cable xing
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on
both the left and right sides.
AC cord xing
Unplug the AC cord
Unplug the AC cord pressing the
two knobs.
Note:
When disconnecting the AC cord, be
absolutely sure to disconnect the AC
cord plug at the socket outlet rst.
hole
To loosen:
hooks
To remove from the unit:
Insert the clamper
in a hole.
Bundle the cables
snaps
Keep pushing
both side
snaps
Set the
tip in the
hooks
knob
Keep
pushing
the knob
Attach the clamper
12
Red
Black
While pressing the lever,
insert the core wire.
Red
Black
Return the lever.
Note:
Please use 8 /10 W speaker.

13
(8Ω,20W[10W+10W])
Connections
Video equipment connection
SLOT: Terminal board (optional
accessories) insert slot
(see page 3)
Note:
The right side slot is for
terminal board with 2-slot width.
The terminal board with 1-slot
width does not function when
installed in the right side slot.
Terminals are on the bottom side of the Plasma Display.
3D IR TRANSMITTER:
Connect the 3D IR
TRANSMITTER
(optional accessory).
SERIAL: Control the
Plasma Display
by connecting
to PC
DVI-D IN: DVI-D Input Terminal
PC IN:
PC Input Terminal
Connect to video terminal of PC or equipment with Y,
P
B (C B ) and P R (C R ) output.
AV IN (HDMI): HDMI Input
Terminal
Connect to video equipment
such as VCR or DVD player.
WIRELESS
MODULE, LAN:
See page 14
AV IN (VIDEO): Composite Video Input
Terminal
COMPONENT/RGB IN: Component/RGB Video
Input Terminal

14
Connections
Example of Network Connection (Wired LAN)
To use the wireless function, the wireless module (ET-WM200E) (sold separately) is necessary.
When connecting the wireless module to the
display, remove the protective lm and cap.
Connecting procedure
Hold the wireless module with its LED on the near
side and connect it to the wireless module connection
terminal.
Note:
Do not connect any other device than the wireless
module (ET-WM200E).
When using the electronic pen
Using the electronic pen with the wireless module
(ET-WM200E) connected may result in malfunction of
the electronic pen due to radio wave interference as
an example. In that case, set “Wireless Lan” to “Off”
before using the electronic pen. (refer to “Operating
Instructions, Network Operations”)
Display (main unit, rear)
Hub or broadband router
LAN cable
(not supplied)
COMPUTER
Less
than
10 cm
Less
than
10 cm
Ferrite core
(supplied)
Ferrite core
(supplied)
Installing the Ferrite core
Pull back the tabs
(in two places)
Wind the cable
twice
Open
Press the cable
through and close
Notes:
• Make sure the broadband router or hub supports 10BASE-T/100BASE-TX.
• To connect a device using 100BASE-TX, use “category 5” LAN cable.
• Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge.
Do not touch the LAN terminal or a metal part of the LAN cable.
• For instructions on how to connect, consult your network administrator.
(8Ω,20W[10W+10W])
ET-WM200
LED
Connecting Wireless Module (Wireless LAN)

INPUT MENU ENTER/ + /VOL - /
15
Power On / Off
Connecting the AC cord plug to the Plasma Display.
Press the button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the switch on the
unit, when the Plasma Display is on or in standby mode.
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
Connecting the plug to the Wall Outlet
Notes:
• Main plug types vary between countries. The power
plug shown at right may, therefore, not be the type
tted to your set.
• When disconnecting the AC cord, be absolutely
sure to disconnect the AC cord plug at the socket
outlet rst.
Press the Power switch on the Plasma Display to
turn the set on: Power-On.
Power Indicator: Green
[Starting up the network]
It takes some time for the network to start up just
after the power is turned on.
During that time, “Network Setup” in the “Setup” menu
is grayed out and cannot be set.
Power Indicator
Remote Control Sensor

Day/Time Setup
Time MON 99:99
Set
Time 99:99
Day MON
Day/Time Setup
Time MON 99:99
Set
Time 10:00
Day TUE
Landscape
Portrait
Display orientation
Italiano
Español
ENGLISH (US)
English (UK)
Deutsch
Français
OSD Language
SetSelect
16
Power On / Off
When rst switching on the unit
Following screen will be displayed when the unit is turned on for the rst time.
Select the items with the remote control. Unit buttons are invalid.
Notes:
• Once the items are set, the screens won't be displayed when switching on the unit next time.
• After the setting, the items can be changed in the following menus.
OSD Language
Day/Time Setup
Display orientation
When 3D images will be viewed by unspecied number of
people or used for commercial applications, someone in
authority should convey the following precautions.
These precautions should be followed in the home as well.
3D Viewing/ 3D Content/ Viewing distance/ 3D Eyewear
recommendations
- To enjoy 3D images safely and comfortably, please
read the Operating Instructions fully.
Power ON warning message
The following message may be displayed when turning the unit power ON:
3D Safety Precautions
No activity power off Precautions
’No activity power off’ is enabled.
If “No activity power off” in Setup menu is set to “Enable”, a warning message is displayed every time
the power is turned ON.
These message displays can be set with the following menu: Options menu
3D Safety Precautions
Power On Message
Activate 3D Safety Precautions if you deliver 3D images to unspecied audiences for business or other purposes.
If “3D Function” in “3D Settings” is set to “On”, a warning message is displayed every time the power is
turned ON.
OSD Language Day/Time Setup Display orientation
1 Select the
language.
2 Set.
1 For vertical installation,
select “Portrait”.
2 Set.
1
Select “Day” or
“Time”.
2
Setup “Day” or
“Time”.
1 Select “Set”.
2 Set.

17
INPUT MENU ENTER/ + /VOL - /
Basic Controls
Main Unit
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu
screen will switch.
Normal Viewing Picture
Sound Pos./Size Setup
INPUT button
(INPUT signal selection)
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is
displayed:
“+”: press to move the cursor
up
“–”: press to move the cursor
down
Enter / Aspect button
Remote control sensor
Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will
still consume some power as long as
the power cord is still inserted into the
wall outlet.)
• Standby ........ Red
Orange (When “Slot power” is set to
“On”.)
Orange (Depending on the type of the function board installed, when the power is supplied to
the slot)
Orange (When “Control I/F Select” is set to “LAN” or “WEB Control” is set to “On”. Refer to
“Operating Instructions, Network Operations”)
• Power-ON ...... Green
• PC Power management (DPMS)
........................Orange (With PC input signal.)
When this function is set to ON, it operates under the following conditions to turn the power on
or off automatically.
When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal
input:
 Power is turned off (standby); the power indicator lights up orange.
When pictures (HD/VD sync signals) are subsequently detected:
 Power is turned on; the power indicator lights up green.
• DVI-D Power management
........................Orange (With DVI input signal.)
• No Signal power off
........................Red
Equipment power supply is turned OFF when there is no signal.
When this is set to “Enable”, the power supply of the unit goes Off 10 minutes after the input
signals stop.

18
Basic Controls
Remote Control Transmitter
Standby (ON / OFF) button
The Plasma Display must rst be
plugged into the wall outlet and turned
on at the power switch (see page 15).
Press this button to turn the Plasma
Display On, from Standby mode.
Press it again to turn the Plasma
Display Off to Standby mode.
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect.
POS./SIZE button
PICTURE button
Sound mute On / Off
Press this button to mute the
sound.
Press again to reactivate sound.
Sound is also reactivated when
power is turned off or volume level
is changed.
N button
POSITION buttons
INPUT button
Press to select Input signal
sequentially.
ECO MODE (ECO)
Press to change the ECO MODE
setup status.
FUNCTION buttons (FUNCTION)
Digital Zoom
AUTO SETUP button
Automatically adjusts the position/
size of the screen.
SET UP button
SOUND button
Volume Adjustment
Press the Volume Up “+” or Down “–”
button to increase or decrease the
sound volume level.
R button
Press the R button to return to
previous menu screen.
OFF TIMER button
The Plasma Display can be preset to switch to
stand-by after a xed period. The setting changes
to 30 minutes, 60 minutes, 90 minutes and 0
minutes (off timer cancelled) each time the button
is pressed.
30 min 60 min
0 min (Cancel)
90 min
When three minutes remain, “Off timer 3 min”
will ash.
The off timer is cancelled if a power interruption
occurs.
RECALL button
Press the “RECALL” button to display
the current system status.
1
Input label
2
Aspect mode
During 3D images
Audio input
Prole name
NANODRIFT Saver operating
3
Touch Pen mode On/Off
4
Off timer
The off timer indicator is
displayed only when the off
timer has been set.
5
Clock display
Touch-Pen On
1
2
3
PC
4:3
 COMPONENT
Memory name: MEMORY2
NANODRIFT
3D
Off timer 90min
4
510:00

19
Specications
TH-65PB1W
Power Source 220 - 240 V AC, 50/60 Hz
Power Consumption
Power on 510 W
Stand-by condition 0.5 W
Power off condition 0.3 W
Plasma Display panel Drive method : AC type 65-inch, 16:9 aspect ratio
Screen size 1,434 mm (W) × 806 mm (H) × 1,645 mm (diagonal)
(No.of pixels) 2,073,600 (1,920 (W) ×1,080 (H)) [5,760 × 1,080 dots]
Operating condition
Temperature 0 °C - 40 °C
Humidity 20 % - 80 %
Applicable signals
Colour System NTSC, PAL, PAL60, SECAM, Modied NTSC
Scanning format 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 60p · 50i ·
50p · 24p · 25p · 30p · 24sF, 1250 (1080) / 50i
PC signals VGA, SVGA, XGA, SXGA, UXGA ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV IN VIDEO
AUDIO L-R
BNC
RCA Pin jack × 2
1.0 Vp-p (75 )
0.5 Vrms, Shared with COMPONENT/RGB IN
HDMI TYPE A Connector
COMPONENT/RGB IN
Y/G
PB/CB/B
PR/CR/R
AUDIO L-R
BNC
BNC
BNC
RCA Pin jack × 2
with sync 1.0 Vp-p (75 )
0.7 Vp-p (75 )
0.7 Vp-p (75 )
0.5 Vrms, Shared with VIDEO
DVI-D IN
AUDIO
DVI-D 24 Pin
Content Protection
Stereo mini jack (M3) × 1
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
0.5 Vrms, Shared with PC IN
PC IN
AUDIO
High-Density Mini D-sub 15 Pin
Stereo mini jack (M3) × 1
Y or G with sync 1.0 Vp-p (75 )
Y or G without sync 0.7 Vp-p (75 )
PB/CB/B: 0.7 Vp-p (75 )
PR/CR/R: 0.7 Vp-p (75 )
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms, Shared with DVI-D IN
SERIAL External Control Terminal
D-sub 9 Pin RS-232C compatible
3D IR TRANSMITTER for 3D IR TRANSMITTER (TY-3D30TRW)
3D SHUTTER OUT
DC 8V OUT
M3 jack × 1
Center plus, for EIAJ 4mm plug
WIRELESS MODULE for Wireless module (ET-WM200E)
LAN RJ45 10BASE-T/100BASE-TX, compatible with PJLink™
EXT SP 8 , 20 W [10 W + 10 W] (10 % THD)
Dimensions (W × H × D) 1,554 mm × 925 mm × 99 mm
Mass (weight) approx. 60.0 kg net (
main unit only )
Note:
Design and specications are subject to change without notice. Mass and dimensions shown are approximate.
Electronic Pen
Type Electronic pen
Transmission system 2.4 GHz radio transmission
Power source Rechargeable AAA Ni-MH battery × 1 or AAA alkaline battery (LR03) × 1
External dimensions (L × H) 198.5 mm × 22.1 mm
Weight Approx. 40 g (including the included rechargeable battery)
Operation time Approx. 4 h (Rechargeable AAA Ni-MH battery)
Approx. 4 h (AAA alkaline battery)
Charging time Approx. 4 h (Rechargeable AAA Ni-MH battery)

Customer’s Record
The model number and serial number of this product can be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of
your purchase to aid in identication in the event of theft or loss, and for Warranty Service purposes.
Model Number Serial Number
Web Site : http://panasonic.net
¤Panasonic Corporation 2012 Printed in Thailand
M0812-0