Panasonic BB-HCM527CE User manual

1. Insert the included CD-ROM into your PC.
• The Setup Program starts. If the program does not start, double-click Setup.exe found
on the CD-ROM.
2. Click [Search for Cameras].
• The program searches for cameras connected to your network.
If [Windows cannot open this file] is displayed after clicking [Manual]
[Select the program from a list] → [OK] → Check [Always use the selected program to open this
kind of file]
→ [Browse] → Browse to [C:\WINDOWS\system32\mshta.exe] → [Open] → [OK]
3. When the Windows Security Alert is displayed, click
[Unblock].
• If the dialog is not displayed, continue to the next step.
4. Select the camera you want to configure, and click
[Access Camera].
• If you have more than one camera, you can distinguish cameras by model number,
printed on the front of the camera, or by MAC address (see “Camera Diagram” on
page 2 of the Installation Guide to find your camera’s MAC address label).
• If more than 20 minutes have passed since the selected camera was turned on, you
cannot configure the camera. Turn off the camera, then turn it on again. This restriction
does not apply to cameras which have not been configured yet or have been reset to
their factory default settings.
• If you are using firewall or antivirus software on your PC, the Setup Program may not
be able to find any cameras on your network. If you cannot disable your firewall or
antivirus software, you can configure the camera by entering its MAC address (see
“Camera Diagram” on page 2 of the Installation Guide to find your camera’s MAC
address label).
5. Enter the desired user name and password, then click
[Save].
• Do not forget the user name and password you set here, otherwise you will need to
reset the camera and configure it again.
6. Enter the user name and password, then click [OK].
•[About this program]: Displays the program’s
version information.
•[Search for Cameras]: Displays a list of cameras
connected to your network.
•[Manual]: Allows you to view the included
documentation. PDF versions of the printed
documentation are included on the CD-ROM;
Adobe®Reader®is required to view them.
•[Update Firmware]: Allows you to use the Setup
Program to update the camera’s firmware (built-in
software).
•[Save Settings to PC/Save Settings to Camera]:
Allows you to save a backup of all camera settings
on your PC, or restore all settings in the camera
using a backup file saved on your PC.
•[Network Camera Recorder with Viewer Software
Single Camera Version Installation]: Installs the
[Network Camera Recorder with Viewer Software
Single Camera Version] software. (See “Installing
the Network Camera Recorder with Viewer Software
Single Camera Version” on page 2.)
•[Exit]: Closes the screen and exits the Setup
Program.
To assign all network settings to the camera
manually, or to assign an IP address using the
DHCP feature of your router, click [Network
Settings], then select [Specify an IP Address] or
[DHCP] and enter the appropriate settings.
If you are using a French, German, Italian,
Spanish, Russian, Simplified Chinese, or
Japanese language OS, this screen will be
displayed in the corresponding language, and all
subsequent camera screens will be displayed in
that language.
Before Reading this Document
This manual is written for both the BB-HCM527 (Indoor Use Only) and the
BB-HCM547 (Outdoor Ready). Available features and operations vary
slightly depending on the model. You can confirm the model no. of your
camera by checking the model no. printed on the front of the camera.
Model number suffixes (“A” and “CE”) are omitted from the following model
numbers shown in this document, unless necessary.
BB-HCM527A, BB-HCM527CE, BB-HCM547A, BB-HCM547CE
Make sure you have read the Important Information document and
followed the instructions in the Installation Guide for connection your
camera.
• Before following the instructions in this document:
– Confirm that your camera is turned on and connected to your router.
– Temporarily disable any firewall or antivirus software on your PC.
– Close your web browser.
• Screen shots shown in this document are for reference only and may vary from what is
displayed on your PC depending on the camera model, network settings, etc.
Abbreviations
• UPnP is the abbreviation for “Universal Plug and Play”.
• The Network Camera is referred to as “the camera” in this document.
• The Setup CD-ROM is referred to as “the CD-ROM” in this document.
Trademarks
• Adobe and Reader are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
• Microsoft, Windows, Windows Vista, Windows Server, ActiveX, and Internet Explorer are
either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
• Screen shots reprinted with permission from Microsoft Corporation.
• All other trademarks identified herein are the property of their respective owners.
• This software is based in part on the work of the Independent JPEG Group.
Setup Guide
Network Camera (PoE Ready)
Model No. BB-HCM527
BB-HCM547
Indoor Use Only
Outdoor Ready
© Panasonic System Networks Co., Ltd. 2008
PQQX16399YA KK0608CM1020
Please read this document before using the product, and save this document for future
reference.
Panasonic Network Camera Website:
http://panasonic.net/pcc/ipcam/

7. When [Setup completed] is displayed, click [To Single
Camera page].
• If the following ActiveX®Controls dialog is displayed, click [Install ActiveX Control...].
• When the following Security Warning is displayed, click [Install].
• The camera image is displayed.
8. Click the [Setup] tab, click [Date and Time] on the left
side of the screen, then set the camera’s date and
time. Click [Save] when finished.
• Screen content varies by model number.
To configure the camera for access from the Internet or from a mobile
phone, continue with the following steps.
Note:
• In order to configure the camera for access over the Internet using these instructions, your
router must be UPnP™compatible and must have its UPnP™feature turned on (it is turned
off by default on most routers). For more information, refer to the operating instructions
included with your router.
• To configure the camera for access over the Internet using a router that does not support
UPnP™, refer to Section 4 Configuring the Camera for Access from the Internet in the
Operating Instructions on the CD-ROM for general information, and refer to the operating
instructions included with your router.
• Disable the maximum idle time setting on your router if you have a PPPoE or PPTP
connection to your Internet Service Provider.
1. Click the [Internet] tab at the top of the camera screen.
2. Select [Enable] under [Auto Port Forwarding (IPv4)],
select [Register with Viewnetcam.com] under
[Viewnetcam.com Registration], then click [Save].
• When the dialog about the camera’s port number changing is displayed, click [OK].
• The camera and router will begin configuring themselves via UPnP™.
• If you select to register with Viewnetcam.com, click [Go to Viewnetcam.com
Registration page] when it is displayed. The Viewnetcam.com website will open
automatically. Follow the on-screen instructions to register.
3. When [Auto Port Forwarding setup is complete.] is
displayed, click [To Single Camera page].
• If you enabled [Auto Port Forwarding (IPv4)], the camera’s port number may have
changed. Do not forget the addresses displayed here.
• To confirm that the camera can be accessed from the Internet using a PC, use a PC
not connected to your network and access the camera using the address displayed
here.
• The IP address or URL used to access the camera over the Internet will also be
displayed on the [Status] page of the [Maintenance] tab.
The CD-ROM includes a single camera version of the Panasonic Network
Camera Recorder with Viewer Software. Click [Manual] on the Network
Camera Setup Program window for details about the installation and
operation of this software.
1. Insert the included CD-ROM into your PC.
• The Setup Program starts. If the program does not start, double-click Setup.exe found
on the CD-ROM.
2. Click [Network Camera Recorder with Viewer Software
Single Camera Version Installation].
3. Follow the on-screen instructions to install the
software.
4. When installation is complete, double-click the
shortcut icon (shown below) on your desktop to start
the software.
Note:
• Network Camera Recorder with Viewer Software Single Camera
Version is compatible with Microsoft®Windows Vista®, Windows®
XP and Windows Server®2003.
• Camera registration is limited to one camera.
• Support is not provided for the single camera version of this
software.
The camera’s IP address is displayed. This is the
IP address you must enter in your web browser to
access the camera. Do not forget this address.
This will install the viewer program (ActiveX
Controls) needed to display camera images
properly. Viewer programs must be installed to
view MPEG-4 images, MJPEG images, and to use
audio features.
Congratulations! You have successfully set up the
camera and can now view camera images.
For more information, refer to 5.4 Setting the Date
and Time in the Operating Instructions on the
CD-ROM.
If you do not wish to configure the camera for access from the
Internet, you can stop here. Return to the Installation Guide and
follow the instructions for mounting the camera.
Access from Internet Configuration
If you are interested in accessing your camera over
the Internet, we recommend using
Viewnetcam.com. Viewnetcam.com is a Dynamic
DNS service designed for use with Panasonic
Network Cameras, and is provided free of charge.
For more information about Viewnetcam.com,
refer to the Viewnetcam.com website
(http://www.viewnetcam.com) for information
about this service.
The camera’s IP addresses for local (LAN) and
Internet access are displayed. These are the IP
addresses you must enter in your web browser to
access the camera over the LAN or from the
Internet. Do not forget these addresses.
Camera setup is now complete. If you have any difficulty
accessing the camera or viewing camera images, refer to the
Troubleshooting Guide on the CD-ROM, otherwise return to the
Installation Guide and follow the instructions for mounting the
camera.
Installing the Network Camera Recorder with Viewer
Software Single Camera Version