Panasonic WV-CS850B User manual

WV-CS850B, WV-CS854BE
ORDER NO. AVS0312524C8
C2003 Matsushita Electric Industrial Co., Ltd.
All rights reserved. Unauthorized copying and
distribution is a violation of law.
Combination Camera
SPECIFICATIONS
Effective Pixels : 752 (H) x 582 (V)
Scanning Area : 3.65 mm (H) x 2.71 mm (V), 1/4”
Synchronization : Internal/Line-lock / Multiplexed Vertical Drive (VD2)
Horizontal Scanning Frequency : 15.625 kHz
Vertical Scanning Frequency : 50.00 Hz
Video Output : 1.0 V[p-p] PAL composite/75 Ω
Horizontal Resolution : More than 480 lines at centre (C/L, NORMAL), more than 510 lines at centre (C/L, HIGH),
570 lines at centre (B/W)
Vertical Resolution : More than 400 lines at centre
Signal-to-Noise Ratio : 50 dB (AGC OFF, weight on)
Dynamic Range : 48 dB (Super Dynamic II ON)
Minimum Illumination : 1 lx (0.1 foot-candle) C/L at SENS UP OFF (AGC HIGH)
0.06 lx (0.006 foot-candle) with PIX SENS UP OFF, B/W, SENS UP OFF (AGC HIGH)
0.03 lx (0.003 foot-candle) with PIX SENS UP B/W at SENS UP OFF (AGC HIGH)
Zoom Speed : Approx. 4.5 s (TELE/ WIDE) in Manual mode
Focus Speed : Approx. 5 s (FAR/NEAR) in Manual mode
Iris : Automatic (Open / Close is possible)/Manual
Maximum Aperture Ratio : 1 : 1.6 (WIDE) - 3.0 (TELE)
Focal Length : 3.79 mm - 83.4 mm
Angular Field of View :
H : 2.6° - 52.3°
V : 2.0° - 39.9°
Electronic Shutter : 1/50 (OFF), AUTO 1/120, 1/250, 1/500, 1/1 000, 1/2 000, 1/4 000, 1/10 000 s
AGC : ON (LOW)/ON (MID)/ON (HIGH)/OFF
Sens UP : MAX 32 times, AUTO/FIX
Super Dynamic II :Selectable ON/OFF (SETUP MENU)
Zoom Ratio : x 22 +Digital Zoom x10
Iris Range : F1.6 - 22, CLOSE
Power Source : 24 V AC, 50 Hz for WV-CS854BE
220 - 240 V AC, 50 Hz for WV-CS850B
The Product with PbF

Power Consumption : 14 W for WV-CS854BE
18 W for WV-CS850B
Ambient Operating Temperature : −10°C - +50°C (14°F - 122°F)
Dimensions : 120 (D) x 191 (H) mm [4-3/4” (D) x 7-1/2” (H)]
Weight : Approx. 2 kg (4.4 lbs)
Auto Focus : MANUAL/AUTO
Auto Mode : OFF/SEQ/SORT/AUTO PAN/PATROL
Auto Pan Key : SEQ/SORT/AUTO PAN/PATROL PLAY
Digital Flip : ON/OFF
Camera ID : Preset ID, Camera ID, Area Title : Up to 16 characters
Motion Detector : ON/OFF
Alarm IN : 4 Inputs (ALARM IN 1 - 4) pulled up to 5.0 V DC OFF (open or 4 V DC - 5 V DC)/
ON (0 V 0.2 mA)
Alarm OUT : 2 Outputs (ALARM/AUX1, B/W/AUX2) open collector - output max. 16 V DC
100 mA OFF (OPEN)/ON (0 V)
B/W Mode : AUTO/ON/OFF
Privacy Zone : ON/OFF, Up to 8 zones
Proportional PAN/TILT : ON/OFF
Patrol: LEARN/PLAY/STOP, Up to 60 seconds
Cleaning : ON/OFF
Panning Range : 360° Endless
Panning Angle Setting : Possible (in Auto-Pan mode)
Panning Mode : Manual/Sequential Position/Sort Position/Auto Pan
Panning Speed : Manual : Approx. 0.1°/s - 120°/s 8 steps/64 steps
Sequence Position : Maximum approx. 300°/s
Tilting Range : 0 - 180° ( - 5° to 185° at 5° tilt angle setting)
CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock.Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
There are special components used in this equipment which are important for safety. These parts are indicated
by the ”Y” mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.
IMPORTANT SAFETY NOTICE
About Lead Free Solder (PbF)
Distribution of PbF PCB:
PCBs (manufactured) using lead free solder (PbF) will have a stamp on the PCB.
Caution:
8Lead free solder has a higher melting point than standard solder.Typically the melting points is 35 °C – 40 °C
(95 °F – 104 °F) higher.Please use a soldering iron with temperature control and adjust it to 360 °C – 370 °C
(680 °F – 698 °F). In case of using high temperature soldering iron, please be careful not to heat too long.
8Lead free solder will tend to splash when heated too high (600 °F / 1112 °F).
8Lead free solder (Sn - 3.0Ag – 0.5Cu) or equivalents are recommended on repairing our lead free soldered PCB.
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.

CONTENTS
Constructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
List of Consumption Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Schematic Diagram
Main Board (1/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Main Board (2/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Main Board (3/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Servo Board (1/2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Servo Board (2/2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Sensor Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Communication Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Power Board for WV-CS850B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Power Board for WV-CS854BE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Conductor View
Main Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Servo Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Sensor Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Communication Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
Power Board for WV-CS850B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Power Board for WV-CS854BE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Exploded View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
ACCESSORIES
Decoration cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
Alarm in cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
Alarm out cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 pc.
Connector for 24 V AC (only for WV-CS854BE) . . . . . . . . . . . . . . . . . . .1 pc.
OPTIONAL ACCESSORIES
Dome cover (approx. 60 % transparency, smoked type) . . . . . . . . . . . .WV-CS2SE
Dome cover (approx. 50 % transparency, smoked type) . . . . . . . . . . . .WV-CS2SHE
Dome cover (approx. 70 % transparency, metal type) . . . . . . . . . . . . .WV-CS2ME
Ceiling Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q105E/WV-Q106E/WV-Q107AE
Wall Mount Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .WV-Q108AE
Tilting Mode : Manual/Sequential Position/Sort Position
Tilting Speed : Manual : Approx. 0.1°/s - 120°/s. 8 steps/64 steps
Sequential Position : Maximum approx. 300°/s
Controls : Pan/Tilt, Lens, 64 Preset Positions, Home Position
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.

– 1-1 –
CONSTRUCTION
qAlarm Input Connector
wAlarm Output Connector
eVideo Output Connector
rData Port
tPower Cable(WV-CS850B)
t*Power Cable(WV-CS854BE)
yCamera Mounting Base
uPanning Start Point
iFall Prevention Wire
oDecoration Cover
!0 Dome Cover
w
e
r
t
t*
q
yu
o
i
!0
(WV-CS850B)
(WV-CS854BE)
CONSTRUCTIONS

LIST OF CONSUMPTION PARTS
MO1 Pan Motor
REF. NO. PART NAME LIFE
MO2 Tilt Motor
MO3 Cooling Fan
* This is working all the time.
Equal to power on time.
* Lens Motor itself is not supplied, but only
supplied as assembly.
M19 Lens (Focus Motor, Zoom Motor)
M6 Slip Ring
8Those figures are just for a reference under 35 ˚C environmental temperature and not for a guarantee.
It changes depending on the actual environment/operating condition.
8Part numbers of these consumption parts are described in Replacement Parts List on page 7-1.
2.16 million PRESET actions
2.16 million AUTOPAN revolutions
(19,200 hours as 32 sec per a turn)
50,000 hours
Each 3.7 million actions
10 million PRESET actions
10 million AUTOPAN revolutions
(88,888 hours as 32 sec per a turn)
– 2-1 –

ADJUSTMENT PROCEDURE
1. Test Equipments Required
8The following Test Equipments are required for
adjustment of the Combination Camera WV-
CS850B/CS854BE.
8Oscilloscope
8Frequency Counter
8Digital Voltmeter
8Vectorscope
8Underscanned Colour Video Monitor
812 V DC Power Supply Unit
8Lux Meter
8Lighting (275 footcandles (2 750 lx), Colour Temperature
3 200 ˚K)
8Personal Computer (IBM PC/AT type or equivalent)
8Standard Straight RS-232C Cable
8White Chart or White Paper
8Radiation Chart
8Colour Temperature Conversion Filters as shown in Table
1-1.
Table 1-1
8Logarithmic Gray Scale Chart (Part No.: YWV2310RB99).
8Colour Chip Chart (Part No.: YWV2100RB98).
8System Controller such as WV-CU151 or WV-CU161.
8Electric Variable Resistor (E.V.R.) kit (Part No.:
YWV0EA1174AN) as shown in Fig. 1-1.
Fig. 1-1
8Extension Cable for the Power Board and the Base Unit
(Part No.:V0EA1266AN) as shown in Fig. 1-2.
Fig. 1-2
8Extension Board Ass'y A- D(Part No.: V0EA1265AN).
Extension Cable Afor CN201 of the Main Board and
the Lens as shown in Fig. 1-3.
Fig. 1-3
Extension Cable Bfor CN4 of the Main Board and CN1
of the Servo Board as shown in Fig. 1-4.
Fig. 1-4
Extension Cable Cfor CN5 of the Servo Board and the
Pan Motor as shown in Fig. 1-5.
Fig. 1-5
Extension Cable Cfor CN2 of the Servo Board and the
Tilt Motor as shown in Fig. 1-6.
Fig. 1-6
Extension Cable Dfor CN1 and CN2 of the
Communication Board and the Base Unit as shown in
Fig. 1-7.
Fig. 1-7
8CCD Mounting Adjustment Jig (Part No. : V0MA1120AN)
as shown in Fig. 1-8.
Fig. 1-8
Part No. Description
KODAK 80B change from 3 200 ˚K to 5 100 ˚K
KODAK 80B and 82C change from 3 200 ˚K to 6 500 ˚K
CN201CN4
CN1
CN5
CN2
CN1CN2
UP
AB
C
UP
AB
CD
– 2-2 –

EReferring to Fig. 2-1-3, disconnect one connector, and
remove three screws that secure the Lower Diecast, and
remove the Lower Diecast Case.
Fig. 2-1-3
RReferring to Fig. 2-1-4, remove four screws that secure
the Inner Dome Cover and pull up the Inner Dome Cover.
Fig. 2-1-4
TReferring to Fig. 2-1-5, loosen one screw and disconnect
one connector.
Fig. 2-1-5
2. Disassembling Procedure
2.1. Disassembling Procedure for Camera
Head
QReferring to Fig. 2-1-1, turn the Dome Cover to counter
clockwise direction, and remove the Dome Cover.
Fig. 2-1-1
WReferring to Fig. 2-1-2, remove one screw and turn the
Lower Diecast Case to the counterclockwise direction
and remove the Lower Diecast Case.
Fig. 2-1-2
Dome Cover Turn to
counterclockwise.
Turn to counter-
clockwise.
Remove one screw.
Lower
Diecast
Case
SW1 SW2
Disconnect one connentor.
Remove three screws.
Lower Diecast
Case
Inner Dome
Cover
Remove four screws.
Disconnect one
connector.
Loosen one
screw.
– 2-3 –

OReferring to Fig. 2-1-9, remove four screws that secure
the Main Board and remove the Main Board and
disconnect one connector.
Fig. 2-1-9
2.2. Slip Ring Replacement Procedure
8After disassembling the camera according to the "2.1
Disassembling Procedure for the Camera Head" Q-
T, carry out the following procedure.
QReferring to Fig. 2-2-1, remove five screws and one
connector that secure the Camera Head Unit, and
remove the Camera Head Unit by pulling it up.
Fig. 2-2-1
YReferring to Fig. 2-1-6, remove two screws that secure
the Lens Cover and remove the Lens Cover .
Fig. 2-1-6
UReferring to Fig. 2-1-7, remove one screw that secure the
Tilt Board.
Fig. 2-1-7
IReferring to Fig. 2-1-8, remove three screws that secure
the Camera Unit and remove the Camera Unit.
Fig. 2-1-8
Remove one screw.
Tilt Board
Remove
two screws.
Lens Cover
Remove one connector. Slip Ring
Remove five screws.
Camera Head Unit
Remove
three screws.
Camera Unit
Remove two screws.
Main Board
Remove two screws
Disconnect
one connector.
– 2-4 –

WReferring to Fig. 2-3-2, remove one screw that secure the
Tilt Chassis Ass'y and remove the Tilt Chassis Ass'y from
the Camera Unit.
Fig. 2-3-2
EReplace the Pan Chassis or the Tilt Chassis with new
one.
2.4. Power Board Replacement Procedure
8After disassembling the camera according to "2.1.
Disassembling Procedure for the Camera Head" Q-
E, carry out the following procedure.
QReferring to Fig. 2-4-1, remove three screws that secure
the Servo Board and remove the Servo Board.
Fig. 2-4-1
WReferring to Fig. 2-2-2, remove three screws that secure
the Slip Ring and remove the Slip Ring.
Fig. 2-2-2
EReplace the Slip Ring with new one.
2.3. Pan Chassis / Tilt Chassis
Replacement Procedure
8After disassembling the camera according to "2.1.
Disassembling Procedure for the Camera Head" Q-
Tand "2.2. Slip Ring Replacement Procedure" Q- E,
carry out the following procedure.
QReferring to Fig. 2-3-1, remove three screws that secrure
the Servo Board and discconect the flexible cable from
the Servo Board CN9 and CN5, then remove the Servo
Board.
Fig. 2-3-1
Remove three screws.
Servo Board
Pan Chassis Ass'y
CN5
CN9
Flexible Cable
Remove one screw.
Camera Unit
Tilt Chassis Ass'y
Remove three screws.
Remove three screws.
Servo Board
– 2-5 –

WReferring to Fig. 2-4-2, remove four screws that secure
the Power Bottom Plate and remove the Power Bottom
Plate.
Fig. 2-4-2
EReferring to Fig. 2-4-3, remove three screws that secure
the Insulation Case and remove the Insulation Case.
Fig. 2-4-3
RReferring to Fig. 2-4-4, remove four screws that secures
the Power Board and remove the Power Board.
Fig. 2-4-4
Remove four screws
Power Bottom Plate
Remove three screws. Insulation Case
Remove four screws.
Power Board
– 2-6 –

2.5. How to Connect the Extension Cables for Servicing
Fig. 2-5-1
8Connect Extension Cable Abetween CN201 of the Main Board and the Lens.
8Connect Extension Cable Bbetween CN4 of the Main Board and CN1 of the Servo Board.
8Connect Extension Cable Cbetween CN5 of the Servo Board and the Pan Motor and between CN2 of the Servo Board and the
Tilt Motor.
8Connect Extension Cable Dbetween CN1 and CN2 of the Communication Board and the Base Unit.
8Supply the power to WV-CS850B/CS854BE.
8Contact the magnet to VS1 on the Servo Board.
CN201
CN4
MAIN BOARD
TILT BOARD
POWER BOARD
SERVO BOARD
Extension Cable A
Extension
Cable B
CN1 CN2
CN5
VS1
Extension Cable C
Extension
Cable C
Extension Cable for the Power Board
and the Base Unit
CN1
CN2
COMMUNICATION
BOARD
to Slip Ring
Extension
Cable D
– 2-7 –

3. Connection and Setting up for
Adjustment
3.1. Connection
8Fig. 3-1-1 shows the connecting diagram for the
adjustment of the WV-CS850B/CS854BE.
Fig. 3-1-1
8Connect the Underscanned Colour Video Monitor to the
Video Output Connector of the E.V.R. Adjustment Kit
through the Vectorscope using the coaxial cables.
8Connect the Video Output Cable of the WV-
CS850B/CS854BE to the CAMERA INPUT Connector of
the E.V.R. Adjustment Kit by the coaxial cable.
8Terminate the input terminal of the Underscanned Colour
Video Monitor with 75Ω.
8Connect the 24V AC Power Supply Unit to the WV-
CS854B or connect the 220-240 V AC Power Supply Unit
to the WV-CS850B.
8Connect the +12 V DC Power Supply Unit to the E.V.R.
Adjustment Kit.
8Connect the E.V.R. Adjustment Kit to IBM PC/AT type
using the Standard Straight RS-232C cable.
8Connect the probe of the Digital Voltmeter, Oscilloscope
or Frequency Counter at the desired Test Point in each
adjustment step.
WV-CS850B
WV-CS854BE
CAMERA
E.V.R.
Adjustment Kit
Personal Computer
Standard
RS-232C
24V AC
Power Supply
(for WV-CS854BE)
220 - 240 V AC (forWV-CS850B)
Floppy Disk
75Ω
Vectorscope Underscanned
Colour Video Monitor
+12V DC
Power Supply
3.2. Setting Up for the Remote E.V.R
Adjustment Kit
< Remote E.V.R Adjustment Kit >
8Fig. 3-2-1 shows the Remote E.V.R. Adjustment Kit.
Fig. 3-2-1
< Switch Setting >
8Referring to Fig. 3-2-2, remove four screws that secure
the Upper Cover and remove the Upper Cover.
Fig. 3-2-2
8Set the switch SW3 on the board to the position as shown
in Fig. 3-2-3.
Fig. 3-2-3
8Set the VP/STD CAMERA selection switch on the rear
panel to STD CAMERA position.
<Rear>
<Front>
Board
SW3
ON
<SW3>
1 2 3 4
Select switch #2 to
ON position.
Remove four screws.
Upper Cover
REMOTE OPERATE
PROG ALARM
RESET
NORMAL
SYSTEM
ALARM OFF
EVR
Left
Switch Right Switch
Mode Selection
Switch
Program
Switch
Up
Switch
Down
Switch Set
Switch
INOUT
STD. CAMERAVP CAMERA VIDEO CAMERA DC12V IN
RS232C
VP/STD Camera Selection Switch
RS232C Connector
REMOTE OPERATE
PROG ALARM
RESET
NORMAL
SYSTEM
ALARM OFF
EVR
– 2-8 –

< Menu Setting >
8Set the Mode Selection Switch on the Front Panel to the
"ALARM OFF"(center) position.
8Keep pressing the Program Switch for 3 seconds or more
until "Program Menu" is displayed on the monitor screen.
8Move the cursor to the "Controller Set Up" position by
pressing the Up and Down Switch.
8Display the "Controller Set Up Menu" on the monitor by
pressing the Set Switch.
8Move the cursor to the "Set Up Disable" position by
pressing the Up and Down Switch.
8Change "Disable" to "Enable" by pressing the Set Switch.
8After completing the above setting, move the cursor to
the Communication position by pressing the Up and
Down Switch.
8Display the "Communication Menu" on the monitor by
pressing the Set Switch.
8After confirming the Baud Rate is 9600, finish this menu
by pressing the Program Switch twice.
< Installing E.V.R Adjustment Program >
8The Example given here is for A 2 drive computer, your
procedure might vary slightly depending on the drive
configuration.
8Confirm that the contents of CONFIG.SYS file on your
computer is DEVICE=ANSI.SYS(Basic).
8Insert floppy disk containing E.V.R. adjustment program
into your floppy drive (for example,drive:A) and type A:
8At the prompt, type CD IBMPC and press ENTER key.
8Type COPY RADJ2.EXE B: and press ENTER key.
8Type CD\ and press ENTER key.
8Type CD SEQ and press ENTER key.
8Type COPY CS854BE.SEQ B: and press ENTER key.
8Type COPY CS85BEAF.SEQ B: and press ENTER key.
8Type COPY CS85BETL.SEQ B: and press ENTER key.
8Type COPY CS85BEPR.SEQ B: and press ENTER key.
8Type CD\ and press ENTER key.
8Type CD EVR and press ENTER key.
8Type COPY CS854BE.EV2 B: and press ENTER key.
8After completing installation of program, you are ready to
use the E.V.R. adjustment program.
3.3. Setting Up for Standard Picture
8The adjustment should be done after 30 minutes warm-up.
8Set the Logarithmic Gray Scale Chart.
8Incident light of 1 400 lx ± 50 lx on the Logarithmic Gray
Scale Chart.
8Aim the Camera at the Logarithmic Gray Scale Chart.
8Set the Camera by the E.V.R. Adjustment Kit so that the
Logarithmic Gray Scale Chart becomes full picture on the
Underscanned Colour Video Monitor.
8Adjust the Lens Focus by the E.V.R. Adjustment Kit to
obtain correct focal point.
8The adjustments should be done with this Standard
Picture, unless otherwise specified.
– 2-9 –

4. Adjustment Procedure
4.1 Camera Adjustment
4.1.1 Starting E.V.R. Adjustment Program
8Insert new floppy disk containing DOS Operating System
and the E.V.R. Adjustment Program into IBM PC/AT and
turn on the IBM PC/AT.
8At the prompt, type RADJ2 CS854BE and press the
ENTER key, then the initial menu page as shown in Fig. 4-
1-1 will be displayed.
Fig. 4-1-1
4.1.2. Saving the Adjustment Data
This saving procedure is recommended to keep the current
adjustment status of the camera.
8Press the SAVE (F5) key of the computer, and the
computer will ask you for the file name.
8Type xxxxxxxx.EV2 CC0 14CA. Give an appropriate file
name for xxxxxxxx within 8 letters, but do not use
CS854BE.
8Press the ENTER key.
4.1.3. Loading the Adjustment Data
This loading procedure is recommended to return the
adjustment status of the camera to the factory default setting
or the setting you saved before.
8Press the LOAD (F1) key of the computer, and the
computer will ask you for the file name.
8Type CS854BE.EV2 or xxxxxxxx.EV2 (xxxxxxxx means
a file name you named before.) and press the ENTER
key.
4.1.4. Adjustment Procedure
8Select the item "1. SC FREQUENCY" with the ARROW
key and press the ENTER key.
(1) Subcarrier Frequency Adjustment for INT mode
Test Point: TD4 (SC VCXO)
8Connect the Frequency Counter to TD4 as shown in Fig.
4-1-2.
Fig. 4-1-2
8Adjust the data with the ARROW key so that the
Subcarrier Frequency becomes 17.734 47 MHz ± 40 Hz.
8Press the ENTER key for the next adjustment.
(2) Subcarrier Frequency Adjustment for LL mode
Test Point: TD4 (SC VCXO)
8Connect the Frequency Counter to TD4 as shown in Fig.
4-1-2.
8Adjust the data with the ARROW key so that the
Subcarrier Frequency becomes 17.734 47 MHz ± 40 Hz.
8Press the ENTER key for the next adjustment.
(3) Line Lock Phase Adjustment
Test Point: Video Output Connector
AC Live Waveform
8Connect the CH1 of the Oscilloscope to the Video Output
Connector.
8Connect the CH2 of the Oscilloscope to the AC Power
Line.
8Trigger the Oscilloscope at V-rate.
8Adjust data with the ARROW keys so that the decay point
of V-sync signal gains 2H ± 4H from the zero-cross point
of the AC Power Line Input Waveforms as shown in Fig.
4-1-3.
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
MENU
PANASONIC EVR ADJUSTMENT SYSTEM (C)MCI Co. CCTV PRODUCT: CS850 EEPROM: 0
<CONTENTS> TD4 17.73447+–40Hz
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD(F1) QUIT(F3) SAVE(F5)
NTSC
1. SC FREQUENCY
2. SC FREQUENCY
3.1. LL PHASE1 FOR AC type (50Hz)
3.2. LL PHASE2 FOR AC type (50Hz)
5. HI CLIP LEVEL
6. PEDESTAL
7. ALC DC
8.1. VIDEO OUT GAIN (L)
8.2. VIDEO OUT GAIN (H)
9.1. BURST LEVEL R
9.2. BURST LEVEL B
9.3. BURST PHASE R
9.4. BURST PHASE B
10.1. WB 3200K MANU OFFSET R
10.2. WB 3200K MANU OFFSET B
11.1. WB 6500K ATW LIMIT R
11.2. WB 6500K ATW LIMIT B
12.1. 3200K R_GAIN
12.2. 3200K B_GAIN
12.3. 3200K R_PHASE
12.4. 3200K B_PHASE
13.1. 5100K R_GAIN
13.2. 5100K B_GAIN
13.3. 5100K R_PHASE
13.4. 5100K B_PHASE
14. HIGHLIGHT CHROMA CLIP

Page (1/1)
Main Board
(Digital Section)
TD4
– 2-10 –

Fig. 4-1-3
8Press the ENTER key for the next adjustment.
8Adjust data with the ARROW keys so that the decay point
of V-sync signal gains 2H ± 4H from the zero-cross point
of the AC Power Line Input Waveforms as shown in Fig.
4-1-3.
8Press the ENTER key for the next adjustment.
(5) High Clip Level Adjustment
Test Point: Video Output Connector
8Aim the Camera at the Logarithmic Grayscale Chart.
8Connect the terminated Oscilloscope with 75Ωto the
Video Output Connector.
8Trigger the Oscilloscope at H-rate.
8Adjust data with the ARROW keys so that the High Clip
Level becomes 790 mV ± 30 mV as shown in Fig. 4-1-4.
Fig. 4-1-4
8Press the ENTER key for the next adjustment.
(6) Pedestal Adjustment
Test Point: Video Output Connector
8Connect the terminated Oscilloscope with 75Ωto the
Video Output Connector.
8Adjust data with the ARROW keys so that the Pedestal
level becomes 50 mV ± 5 mV as shown in Fig. 4-1-5.
Fig. 4-1-5
8Press the ENTER key for the next adjustment.
(7) ALC DC Level Adjustment
Observe: Video Monitor
8Aim the Camera at the Logarithmic Grayscale Chart.
8Adjust data with the ARROW keys so that the second data
from left becomes between 00 and 05 on the Video
Monitor as shown in Fig. 4-1-6.
Fig. 4-1-6
8Press the ENTER key for the next adjustment.
(8) Video Out Gain Adjustment
Test Point: Video Output Connector
8Aim the Camera at the Logarithmic Grayscale Chart.
8Connect the terminated Oscilloscope with 75Ωto the
Video Output Connector.
8Adjust data with the ARROW keys so that the Video
Output signal level becomes 700 mV ± 50 mV as shown in
Fig. 4-1-7.
Zero-Cross Point
AC Line Input
Waveform
Video Output
Signal Waveform
2H ±4H
– +
V SYNC
790 mV ±30 mV
50 mV ±10 mV
00 00 00 00 1C 10 88 30
Second data becomes between 00 and 05.
(Data are just example.)
– 2-11 –

Fig. 4-1-7
8Press the ENTER key for the next adjustment.
8Adjust data with the ARROW keys so that the Video
Output signal level becomes 700 mV ± 50 mV as shown in
Fig. 4-1-7.
8Press the ENTER key for the next adjustment.
(9) Burst Level and Phase Adjustment
Test Point: Video Output Connector
8Aim the Camera at the Logarithmic Grayscale Chart.
8Connect the terminated Oscilloscope with 75Ωto the
Video Output Connector.
8Adjust data with the ARROW keys so that the Burst signal
level becomes 300 mV ± 10 mV as shown in Fig. 4-1-8.
Fig. 4-1-8
8Press the ENTER key for the next adjustment.
8Adjust data with the ARROW keys so that the Burst signal
level becomes 300 mV ± 10 mV as shown in Fig. 4-1-8.
8Press the ENTER key for the next adjustment.
8Set the Mode Switch of the Vectorscope to "NTSC" mode.
8Adjust data with the ARROW keys so that the Burst Phase
becomes 135˚±1˚as shown in Fig. 4-1-9.
Fig. 4-1-9
8Set the Mode Switch of the Vectorscope to "PAL" mode.
8Adjust data with the ARROW keys so that the Burst Phase
becomes 90˚±2˚as shown in Fig. 4-1-9.
8Press the ENTER key for the next adjustment.
8Set the Mode Switch of the Vectorscope to "NTSC" mode.
8Adjust data with the ARROW keys so that the Burst Phase
becomes 135˚±1˚as shown in Fig. 4-1-9.
8Set the Mode Switch of the Vectorscope to "PAL" mode.
8Adjust data with the ARROW keys so that the Burst Phase
becomes 90˚±2˚as shown in Fig. 4-1-9.
8Select "9.1. BURST LEVEL R" with the ROLLDOWN key.
8Repeat this adjustment (9) until both Burst Level and
Phase are adjusted to proper position as shown in Fig. 4-
1-8 and Fig. 4-1-9.
8Press the ENTER key for the next adjustment.
(10.1) White Balance 3200 ˚K Manual Offset R
Adjustment
Test Point: Video Output Connector
8Set the gain control of the Vectorscope to maximum.
8Aim the Camera at the White Chart or the White Paper.
8Adjust data with the ARROW key so that the vector
positions at the center of the Vectorscope as shown in Fig.
4-1-10.
Fig. 4-1-10
8Press the ENTER key for the next adjustment.
700 mV ±50 mV
300 mV ±10 mV
135 ±1 °
NTSC mode PAL mode
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
90 ±2 °
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
Positions at center.
– 2-12 –

(10.2) White Balance 3200 ˚K Manual Offset B
Adjustment
Test Point: Video Output Connector
8Aim the Camera at the White Chart or the White Paper.
8Adjust data with the ARROW key so that the vector
positions at the center of the Vectorscope as shown in Fig.
4-1-10.
8Repeat adjustment from (10.1) to (10.2) until the vector
positions at the center of the Vectorscope.
8Press the ENTER key for the next adjustment.
(11.1) White Balance 6500 ˚K ATW Limit R
Adjustment
Test Point: Video Output Connector
8Aim the Camera at the White Chart or the White Paper.
8Change the colour temperature from 3 200 ˚K to 6 500 ˚K
by mounting colour temperature conversion filters on the
lens.
8Adjust data with the ARROW key so that the vector
positions at shift by 10 % to the Cyan side of the
Vectorscope as shown in Fig. 4-1-11.
Fig. 4-1-11
8Press the ENTER key for the next adjustment.
(11.2) White Balance 6500 ˚K ATW Limit B
Adjustment
Test Point: Video Output Connector
8Aim the Camera at the White Chart or the White Paper.
8Keep the colour temperature to 6 500 ˚K.
8Adjust data with the ARROW key so that the vector
positions at shift by 10 % to the Cyan side of the
Vectorscope as shown in Fig. 4-1-11.
8Repeat adjustment from (11.1) to (11.2) until the vector
positions at shift by 10 % to the Cyan side of the
Vectorscope.
8Press the ENTER key for the next adjustment.
(12.1) 3200 ˚K R Gain Adjustment
Test Point: Video Output Connector
8Aim the Camera at the Colour Chip Chart.
8Set the gain control of the Vectorscope to the normal
position.
8Return the colour temperature from 6 500 ˚K to 3 200 ˚K
by removing colour temperature conversion filters from the
lens.
8Adjust data with the ARROW keys so that the Red gain
becomes 220 % ± 5 % (Burst Level = 100 %).
8Press the ENTER key for the next adjustment.
(12.2) 3200 ˚K B Gain Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Yellow gain
becomes 100 % ± 5 % (Burst Level = 100 %).
8Press the ENTER key for the next adjustment.
(12.3) 3200 ˚K R Phase Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Red Vector
phase becomes 108˚±2˚.
8Press the ENTER key for the next adjustment.
(12.4) 3200 ˚K B Phase Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Yellow
Vector phase becomes 160˚±8˚.
8Repeat adjustment from (12.1) to (12.4) until both
Chrominance Phase and Gain are adjusted to proper
positions as shown in Fig. 4-1-12 and Table 4-1-1.
Fig. 4-1-12
Table 4-1-1
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
Shifts approx. 10%.
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
Phase
Gain
Red
108°±2°
220% ±5%
Yellow
160°±8°
100% ±5%
(Cyan)
290°±8°
160% ±10%
– 2-13 –

8Press the ENTER key for the next adjustment.
(13.1) 5100 ˚K R Gain Adjustment
Test Point: Video Output Connector
8Aim the Camera at the Colour Chip Chart.
8Change the colour temperature from 3 200 ˚K to 5 100 ˚K
by mounting colour temperature conversion filters on the
lens.
8Adjust data with the ARROW keys so that the Red gain
becomes 220 % ± 5 % (Burst Level = 100 %).
8Press the ENTER key for the next adjustment.
(13.2) 5100 ˚K B Gain Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Yellow gain
becomes 100 % ± 5 % (Burst Level = 100 %).
8Press the ENTER key for the next adjustment.
(13.3) 5100 ˚K R Phase Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Red Vector
phase becomes 108˚±2˚.
8Press the ENTER key for the next adjustment.
(13.4) 5100 ˚K B Phase Adjustment
Test Point: Video Output Connector
8Adjust data with the ARROW keys so that the Yellow
Vector phase becomes 160˚±8˚.
8Repeat adjustment from (13.1) to (13.4) until both
Chrominance Phase and Gain are adjusted to proper
positions as shown in Fig. 4-1-13 and Table 4-1-2.
8Press the ENTER key for the next adjustment.
Fig. 4-1-13
Table 4-1-2
(14) Highlight Chroma Clip Adjustment
Test Point: Video Output Connector
8Connect the terminated Oscilloscope with 75Ωto the
Video Output Connector.
8Aim the Camera at the White Chart or the White Paper.
8Return the colour temperature from 5 100 ˚K to 3 200 ˚K
by removing colour temperature conversion filters from the
lens.
8Set data to FF with the ARROW keys.
8Adjust data with the RIGHT key so that the False
Chrominance Level becomes minimum for the first time as
shown in Fig. 4-1-14.
Fig. 4-1-14
8After completing the adjustment, press the QUIT (F3) key,
then the computer will ask you if you want to save the
current adjustment status.
8If you want to save, press the Ykey, and then press the
ENTER key. Type xxxxxxxx.EV2 CC0 14CA. Give an
appropriate file name for xxxxxxxx within 8 letters, but do
not use CS854BE. Then press the ENTER key to finish
the adjustment procedure.
8If you don't want to save, press the Nkey, and then press
the ENTER key to finish the adjustment procedure.
cy
gMG
YL
yl B
b
GCY
dG
10°
0°
10°
dø 100%
75%
RV
U
mg
r
20%
20%
dG
Phase
Gain
Red
108°±2°
220% ±5%
Yellow
160°±8°
100% ±5%
(Cyan)
290°±8°
160% ±10%
Minimize Chromi-
nance Level.
– 2-14 –

ePlace the Camera facing down more than 5 degrees
(ideally 90 degrees) from the level as shown in Fig. 4-2-
2.
rSet the Radiation Chart more than 10 m away from the
Camera as shown in Fig. 4-2-2.
Fig. 4-2-2
Note: The air holes on the Lens Cover should be down
facing floor.
tIf 10 m is not secured between the Camera and the
Radiation Chart:
Place the camera facing down more than 5˚from the
level.
Pat the camera body gently. (See the Note below.)
Then place the camera carefully on the table as shown in
Fig. 4-2-3. (Do not give any vibration to the camera.)
Fig. 4-2-3
Radiation Chart
10 m
more than 5˚
Radiation Chart
Table
10 m
Note: Reason for facing the camera down.
The Zoom-Lens unit has a moving lens inside. This moving lens
requires a tolerance (10 µm order) when starts to move.
Because of 1/4" CCD and x22 zooming ratio, the tolerance will
affect the focal point.
When adjusting the camera with the Lens facing down, the
tolerance will be always pulled downward by the gravity, which
makes it possible to adjust back focus as the best.
4.2 Back Focus Adjustment
Note) This tilt adjustment is required in the following cases;
1. Replacing the CCD image sensor.
2. Replacing the Sensor Board.
4.2.1 Starting E.V.R Adjustment Program
8Insert new floppy disk containing DOS Operating System
and the E.V.R Adjustment Program into IBM PC/AT and
turn on the IBM PC/AT.
8At the prompt, type RADJ2 CS85BEAF and press the
ENTER key, then the initial menu page as shown in Fig. 4-
2-1 will be displayed.
Fig. 4-2-1
4.2.2. Saving the Adjustment Data
This saving procedure is recommended to keep the current
adjustment status of the camera.
8Press the SAVE (F5) ke of the computer, and the
computer will ask you for the file name.
8Type xxxxxxxx.EV2 CC0 14CA. Give an appropriate file
name for xxxxxxxx within 8 letters, but do not use
CS854BE.
8Press the ENTER key.
4.2.3. Loading the Adjustment Data
This loading procedure is recommended to return
theadjustment staturs og the camera to the factory default
setting or the setting you saved before.
8Press the LOAD (F1) key og the computer, and the
computer will ask you for the file name.
8Type CS854BE.EV2 or xxxxxxxx.EV2 (xxxxxxxx means
a file name you named before.) and press the ENTER
key.
4.2.4. Adjustment Procedure
qSelect the item "1.1 PAN / TILT POSITION" with the
ARROW key.
wPress the ENTER key for presetting the lens position.
The lens turns to the center of the Dome Cover.
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
MENU
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT: CS850 EEPROM: 0
<CONTENTS> PAN / TILT
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD(F1) QUIT(F3) SAVE(F5)
NTSC
1.1. PAN / TILT POSITION
1.2. BACK FOCUS ADJUST
Page (1/1)
– 2-15 –

4.3 Tilt Adjustment
Note) This tilt adjustment is required in the following cases;
1. Replacing the CCD image sensor.
2. Replacing the Sensor Board.
3. Replacing the Tilt Board.
4.3.1 Preparation
QDraw the horizontal line on the center of the Video
Monitor Screen as shown in Fig. 4-3-1.
Fig. 4-3-1
WPlace the camera on the table as shown in Fig. 4-3-2.
ESet the white paper 1.6 m ± 100 mm away from the
camera as shown in Fig. 4-3-2.
RDraw the horizontal five lines of 1mm interval on the
paper and center line is 145 mm from the top of the table
as shown in Fig. 4-3-2.
Fig. 4-3-2
Horizontal Line Monitor Screen
yAfter confirming that there is no other object between the
Camera and the Radiation Chart, press the ENTER key.
uWait about 40 seconds until finishing the Back Focus
adjustment.
iConfirm that the picture is clearly visible during zooming
wide.
oIf the picture is not clearly visible, press ESC key and,
select the item “1.2. BACK FOCUS ADJ” with the
ARROW key, and press the ENTER key.
!0 Repeat above adjustment steps y- ountil the picture
becomes fine.
!1 After completing of the adjustment, press the QUIT (F3)
key.
!2 Press the Nkey, then press the ENTER key to finish this
adjustment procedure.
1.6m ±100mm
145 mm
Horizontal Line
Table
White Paper
1mm
– 2-16 –