Panasonic BL-C10A - Network Camera - Pan User manual

Additional Feature table
The following features are added to the camera. Read both Operating Instructions
manuals before starting to use the product.
Additional Features Contents Page
Banner can be displayed
(Added to page 10 of the
Operating Instructions on the
Setup CD-ROM.)
When the camera accesses the
Internet, the banner displays product
information about cameras or
announcements about the latest
firmware, etc. from Panasonic..
page 2
Banner can be set
(Added to page 47 of the
Operating Instructions on the
Setup CD-ROM.)
When checked, the banner is displayed
for administrator or general users or
both.
page 3
Save button is added on the
Buffer/Transfer page
(Added to page 51 and page 58 of
the Operating Instructions on the
Setup CD-ROM.)
You can change the trigger enable/
disable setting of the buffer/transfer
feature.
page 4
Sensor deactivation after initial
detection
(Added to page 61 of the
Operating Instructions on the
Setup CD-ROM.)
You can set sensor deactivation time
during which the sensor does not work
in order not to send too many E-mails
to a mobile phone.
page 5
Turn the indicator on during the
sensor reaction
(Added to page 69 of the
Operating Instructions on the
Setup CD-ROM.)
You can set indicator to light orange
during the sensor reaction.
page 6
Operating Instructions (Additional Features)
Model No. BL-C10A
Network Camera

Operating Instructions (Additional Features)
2
Banner can be displayed
When the camera accesses the Internet, the banner displays product information
about cameras or announcements about the latest firmware, etc. from Panasonic.
1. Access the camera (see page 8 of the Operating Instructions on the Setup CD-
ROM).
• The Top page is displayed.
2. Click the [Single] tab at the top of the page.
When the camera is accessed,
a banner can be displayed
below the image. The banner
announces firmware updates
and new product announcements.
It can be configured so that it is
seen by the Administrator or
General User or both.
It can be also disabled.

Operating Instructions (Additional Features)
3[For assistance, please call: 1-800-272-7033]
Banner can be set
When checked, the banner is displayed for administrator or general users or both.
Setting Description
Banner Display • When the user accesses the camera, the banner
displays firmware updates or new product
announcements. Checking [Display] for Administrator
is particularly recommended.
• When checked, the banner is displayed for
administrator or general users or both.
• The banner is displayed only on the Single Camera
page (see page 2).
Banner can be set.

Operating Instructions (Additional Features)
4
Save button is added on the Buffer/Transfer page
You can change the trigger enable/disable setting of the buffer/transfer feature.
1. Click [Buffer/Transfer] on the Setup page.
2. Click [No.] to enable buffer/transfer.
• Trigger setting page is displayed.
Clicking [Save] saves the settings.
The buffered images are deleted.
You can change the trigger enable/disable setting.

Operating Instructions (Additional Features)
5[For assistance, please call: 1-800-272-7033]
Sensor deactivation after initial detection
You can set sensor deactivation time during which the sensor does not work in
order not to send too many E-mails to a mobile phone.
Setting Description
Sensor
deactivation
time setting
• Set the time period during which the sensor does not work
after detection. This function is recommended to use not to
send too many E-mails to a mobile phone.
• Sensor transfer stops its operations until the camera
finishes all transfers. For example, if the camera transfers
3 images per minute and 6 images in total with setting 1
minute of sensor deactivation time, the sensor will be in the
following operation.
Note
Since the camera cannot buffer images during sensor
deactivation time, the images before detection also cannot
be buffered. For example, if you set "1 image per second
and totally 10 images before detection" and the sensor
detect the heat changes right after the previous detection,
the images are not buffered. If 10 seconds pass after the
sensor deactivation time ends, images can be buffered as
you set.
Set the time for the
sensor not to work
after detection.
Detectable UndetectableUndetectable
1st 2nd 3rd 4th 5th 6th
120 seconds
A heat change occurs.
Detectable
Sensor
deactivation
time
1 minute

Operating Instructions (Additional Features)
6
Turn the indicator on during the sensor reaction
You can set indicator to light orange during the sensor reaction.
• If the sensor detects temperature changes, the indicator lights orange
despite the image buffer/transfer feature. You can recognize the sensor
detection range while seeing the indicator.
Make the indicator light orange during sensor reaction.

Operating Instructions (Additional Features)
7[For assistance, please call: 1-800-272-7033]
Default Setting List
Items Default Required Notes
Image
Display
Banner Display
Administrator Checked - -
General User Checked - -
Buffer/
Tr an s fe r
Sensor deactivation
time setting
No
appointment
When you set
sensor
transfer
No appointment,
10, 30 (s), 1, 3, 5,
10 (min)

Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
PSQX3504YA KK0904RM1035
2004 Panasonic Communications Co., Ltd. All Rights Reserved.
Panasonic Puerto Rico, Inc.
The information in this document is subject to change without notice.
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced
for internal use only. All other reproduction, in whole or in part, is prohibited without the written
consent of Panasonic Communications Co., Ltd.