Panasonic aw-he40 series User manual

★ This is to explain the procedure for adding another AW-HE40 camera as CAM4 to an existing system that consists
of three AW-HE40 cameras and one AW-R 50 controller.
1. Connect AW-HE40 LAN port and the hub using a LAN cable. (AW-HE40 can automaticall recognize whether
it is a cross or straight cable.)
* LAN Cable: Category 5 or higher, Up to 100m (Category 5e or higher if connected via a oE+ compatible hub)
2. B [1] CAMERA CTL setting, select [No Asign] for the CAMERA No. ou want to add.
① ress MENU button. - (Fig. 1-A)
② ress [10] SYSTEM button. - (Fig. 1-B) * “[1] CAMERA CTL” will be displayed on the LCD screen. - (Fig. 2)
* If it is not displayed, turn F1 dial to make “[1] CAMERA CTL” appear.
③ While “[1] CAMERA CTL” is displayed on the LCD screen, press F1 dial. - (Fig. 1-C)
④ Turn F1 dial to make [CAM4] appear. - (Fig. 2)
⑤ Turn F2 dial to select [No Asign], then press F2 dial to determine the setting. - (Fig. 1-D)
Turn F2 ⇒ Select “No Asign” ⇒ ress F2 to determine
Adding Another AW-HE40 Camera to Existing S stem
MENU ON ⇒ Select [10]
［1］CAMERA CTL
ress F1
1. CAM1
Network
2. CAM2
Network
3. CAM3
Network
Installed & Set Alread
4. CAM4
No Asign
Turn F1
（A）
（B）
（C）
（D）
(Figure 1)
(Figure 2)

3. B [5] AUTO SET IP setting, execute the automatic assignment of IP addresses. (RENEW IP ADR)
① In the state of the above-mentioned 2.-②, turn F1dial to select [5] AUTO SET I .
② ress F1 dial to make [RENEW I ADR] appear on the lower half of the LCD screen.
* If it does not appear, turn F2 dial to make [RENEW I ADR] appear.
③ While [RENEW I ADR] is displayed, press F2 dial. The number of units that AW-R 50 has newly
detected and the number of units that it currently manages (all the remote cameras and switchers) will
be displayed on the upper half of the LCD screen.
④ [NO] will be displayed on the lower half of the LCD screen. So, turn F2 dial to select [YES] and then
press F2 dial.
⑤ When [COM LETE] is displayed on the lower half of the LCD screen, the setting-up is completed.
After setting up, LED button 4 (CAM4) at <CAMERA STATUS / SELECTION> on the AW-R 50 operation panel lights
up in a few seconds according to the camera’s power status. If the camera is in STANDBY mode (power OFF:
factory default), the button lights up in orange. If in OWER ON mode (power ON), it lights up in green.
* When the camera is in STANDBY mode, the ower-ON operation needs to be done.
For the procedure, please refer to “3. Turn AW-HE40 on” of the Manual 【Controlling AW-HE40 Camera via
AW-R 50 Controller】.
(AW-R 50: CAMERA STATUS/SELCTION Area)
[5] AUTO SET IP
［1］CAMERA CTL
MENU ON ⇒ Select [10]
Turn F1
ress F1
1. AUTO SET
RENEW IP ADR
C:001/004 S：0/1
NO ↓
C:001/004 S：0/1
YES
↓
C:001/004 S：0/1
COMPLETE
Turn F2
ress F2
ress F2
After setting up, this lights up
according to the camera’s
power status.
* If it does not light up, please check the following points.
① Check the connection state of LAN cable or whether you are using a cable that meets the specifications.
② Check that the LAN cable is connected to “LAN port”, not to “RS422 port”.
③ Double-check that there is no error in setting up the connection.