Panasonic RX-CS40 User manual

RX-CS40 RQT7635
RQT7635-G
GC GU GS
Dear customer
Thank you for purchasing this product.
Before connecting, operating or adjusting this product, please read
these instructions completely.
Please keep this manual for future reference.
Table of contents
Control guide.................................................................................3
Speaker connection.....................................................................4
Power supply.................................................................................5
The radio .........................................................................................6
Tapes................................................................................................7
Recording the radio .....................................................................8
Other functions .............................................................................9
Troubleshooting guide .............................................................10
Maintenance.................................................................................11
Specifications..............................................................................11
Supplied accessories
Check the packaging for these accessories.
1 AC power supply cord
The included AC power supply cord is for use with this unit only.
Do not use it with other equipment.
Note
Portable Stereo Component System
Operating Instructions
Model No. RX-CS40
RX-CS40RQT763504.2.610:29ページ1

2
RQT7635
CAUTION!
•DO NOT INSTALL, OR PLACE THIS UNIT IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY
OTHER MATERIALS DO NOT OBSTRUCT THE
VENTILATION VENTS.
•DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS
WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND
SIMILAR ITEMS.
•DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS
LIGHTED CANDLES, ON THE UNIT.
•DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO
RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL
BE PLACED ON THE APPARATUS.
This product may receive radio interference caused by mobile
telephones during use. If such interference is apparent, please
increase separation between the product and the mobile
telephone.
THIS UNIT IS INTENDED FOR USE IN TROPICAL CLIMATES.
The speakers do not have magnetic shielding. Do not place the
unit near televisions, personal computers or other devices easily
influenced by magnetism.
CAUTION:
Change the voltage setting to suit the AC voltage in your
area. See page 5. Note that the unit will be seriously damaged
or fail to operate correctly if this setting is not made
correctly.
The socket outlet shall be installed near the equipment and easily
accessible or the mains plug or an appliance coupler shall remain
readily operable.
RX-CS40RQT763504.2.610:30ページ2

RX-CS40 RQT7635
3
RQT7635
Speakers (Woofer)
Speakers (Tweeter)
Built-in microphone (MIC)
Preset equalizer buttons
Band selector (BAND)
Operation/battery indicator (OPERATION/BATT)
FM mode/beat proof selector (FM MODE/BP)
Fine tuning control (FINE TUNING)
Function selector (SELECTOR)
Tuning control (TUNING)
Volume control (VOLUME)
Audio input terminal (CD/LINE IN)
Headphones jack (PHONES)
Cassette holder
XBS adjustor (XBS)
Recording button ( REC)
Playback button ( PLAY)
Rewind/review button ( REW/REV)
Fast forward/cue button ( FF/CUE)
Stop/eject button ( STOP/EJECT)
Pause button ( PAUSE)
Speaker release levers (RELEASE)
Speaker terminals (SPEAKERS)
Audio input level switch (CD/LINE IN)
Whip antenna
Speaker cord compartments
Speaker cords
DC input jack (DC IN)
AC socket (AC IN~)
Voltage selector (VOLT ADJ)
Battery compartment cover
Control guide
15
14
12
16 18 20
17 19 21
43 5 6 78910 11 12 13
29 30 3128
22 2524
26 27
23
RX-CS40RQT763504.2.610:30ページ3

4
RQT7635
Connect the speaker cords
AAttaching the speakers BDetaching the speakers C
Before attaching or detaching the speakers,
Be sure to disconnect the speaker cords.
Be sure to set [SELECTOR] to “TAPE/ ”.
• The function selector switch does not separate entire unit from
mains even if in “TAPE/ ” position.
OPR OFF
OPR OFF
Caution
•Use the speakers only with the recommended system.
Failure to do so may lead to damage to the amplifier and/or
the speakers, and may result in the risk of fire.
Consult a qualified service person if damage has occurred
or if you experience a sudden change in performance.
•Do not attach these speakers to walls or ceilings.
Speaker connection
1
2
Connect only positive (red) wires to positive terminals and
negative (black) wires to negative terminals.
Unlock the speaker release levers by pulling them in direction shown
as illustrated, and slide each speaker up.
RELEASE RELEASE
Connect the speaker cords
A
Detaching the speakers
C
Attaching the speakers
B
Align the speaker with the main unit as shown in the figure, interlock
the grooves and press down.
RX-CS40RQT763504.2.610:30ページ4

RX-CS40 RQT7635
5
RQT7635
Set the voltage.
Use a flat-head screw-driver to turn the voltage selector for the
area in which the unit will be used.
Connect the AC power supply cord (included).
AC power supply cord
ABatteries BCar battery cord C
Insert the plug into the DC Input Jack.
Plug the other end into the cigarette lighter socket in your car.
Power supply
AC power supply cord
A
Cautions
Insert your finger into the slot ( ) at the bottom of the unit and push
out the batteries.
Removal
Disconnect the AC power supply cord.
Replace the batteries when “OPERATION/BATT”goes dim during
play.
To prevent damage to the batteries and electrolyte leakage, heed the
following points.
•Do not use rechargeable type batteries.
•Align the and polarities properly when inserting the batteries.
•Do not mix different types or makes of batteries or old and new
batteries.
•Remove batteries if you do not plan to use the unit for a long time.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
Batteries
B
Car battery cord
C
1
2
AC IN ~
VOLT ADJ
110-127V
220-
240V
220-240V
220-
240V
110-
127V 110-
127V
R20/LR20 (D, UM-1)
354
6
8
7
1
2
a
DC IN
(12-13.2V)
12
•Do not touch it with wet hands.
•Do not place heavy objects on it.
•Poor connection and cord damage can cause fire or electric shock.
•Grasp the plug firmly when unplugging the cord. Pulling the AC
power supply cord can cause electric shock.
•Disconnect the AC power supply cord from the household AC outlet
if the unit is not going to be used for a long time.
To household
AC outlet
RX-CS40RQT763504.2.610:30ページ5

FM: Raise and extend the whip antenna.
If stereo reception is poor, set [FM MODE/BP] to “MONO”.
MW:Turn the unit to face in the direction of best reception.
SW:Raise and extend the whip antenna and keep it vertical
(SW1: also turn the unit to face in the direction of best reception).
Reference:
Radio broadcasts may be hard to receive in a moving vehicle or
building because their signals are weak. Whenever possible, use the
unit by a window.
6
RQT7635
To improve reception
A
For short-wave broadcasts (SW1, SW2), tune to the approximate
frequency with [TUNING], and then use [FINE TUNING] control for
more precise tuning.
When using [TUNING], be sure to set [FINE TUNING] control pointer
to the center position.
Note
Fine tuning control
The radio
Follow steps 1 to 3.
In step 1: “OPERATION/BATT”lights while the radio is on.
In step 2: Select FM, MW, SW1 or SW2.
To turn off the radio
Set [SELECTOR] to “TAPE/ ”.
OPR OFF
123
TUNING
CD/
LINE IN
RADIO
TAPE/
SELECTOR
STEREO/
MONO/
FM MODE/BP
LH
FINE TUNING
OPERATION/BATT
FM MW SW1 SW2
BAND
MW/SW1
FM
SW1/SW2
To improve reception
A
RX-CS40RQT763504.2.610:30ページ6

RX-CS40 RQT7635
7
RQT7635
Caution
Sound quality may be effected and the cassette tape may become
stuck if you do not adhere to the following.
•Do not use other stickers not included with the cassette tape.
•Place stickers on the cassette tape only as indicated.
Tapes
Use normal position/TYPE I tape only.
Follow steps 1 to 3.
In step 1: Set to “TAPE/ ”.
OPR OFF
In step 2: Insert the tape with the side to be played facing out ( ) and close
by hand.
•Tapes exceeding 100 minutes are thin and can break or get caught in the
mechanism.
•Tape slack can get caught up in the mechanism and should be taken up
before playing the tape.
•Endless tapes can get caught up in the mechanism if used incorrectly.
“OPERATION/BATT”indicator
Lights while the tape is travelling.
To stop play
Press [ STOP/EJECT].
To pause play
Press [ PAUSE].
Press once again to resume play.
To fast-forward or rewind (while stopped)
Press [ REW/REV] or [ FF/CUE].
To cue or review (during play)
Press [ REW/REV] or [ FF/CUE].
SELECTOR
CD/
LINE IN
RADIO
TAPE/
123
OPERATION/BATT
RX-CS40RQT763504.2.610:30ページ7

8
RQT7635
Erasure preventionA
Recording the radio
Erasure preventionA
Use normal position/TYPE I tape only.
Follow steps 1 to 3.
In step 1: Set [SELECTOR] to “RADIO”and tune to the station. ( page 6)
In step 2: Insert the tape inside with the side to be recorded facing out and
close by hand.
In step 3: [ PLAY] is also depressed with [ REC].
Recording stops and the button is released when the front side finishes.
To stop recording
Press [ STOP/EJECT].
To pause recording
Press [ PAUSE].
To resume recording, press [ PAUSE] again.
•Changes to volume and tone will not affect the recording.
•Wind up the leader tape before recording.
•When recording MW, set [FM MODE/BP] to the position where
there is less noise.
•Use the AC power supply cord or insert fresh batteries.
Break out the tab.
Cover the tab with adhesive tape when you want to use the tape for
recording again.
Recording tips
TUNING
123
STEREO/
MONO/
FM MODE/BP
Side A
Tab for Side B Tab for Side A
RX-CS40RQT763504.2.610:30ページ8

RX-CS40 RQT7635
9
RQT7635
Equalizer/
Headphones
C
•Four types of sound effects can be selected.
The selected sound effect button lights.
CLEAR: Lightens pop and other music
SOFT: Allows background music enjoyment
HEAVY: Adds punch to rock
VOCAL: Enhances vocals
FLAT: No sound effects used
•You can adjust XBS effect to boost the bass.
When you initially apply the power source
•The preset equalizer will automatically reset to “HEAVY”when the
unit is turned on.
When the unit is in condition and when the power
source is connected
•The last preset equalizer setting will be retained when you turn on
the “CD/LINE IN”, “RADIO”or “TAPE”function.
OPR OFF
Note
Face towards the sound source.
•When recording through the built-in microphone, no sound can be
heard from the speakers.
Note
Other functions
Equalizer
Recording through the built-in microphone
(MIC)
Headphones
To connect headphones,
Plug type: 3.5 mm stereo
Plug in firmly. Avoid listening for prolonged periods of time to prevent
hearing damage.
B
C
C
Connect the CD player (External equipment).
Start recording, then start the CD playback.
•Turn off all equipment before making any connection.
•Refer to the operating instructions of the other equipment for
details. (Cables and equipment not included.)
•If the signal level from the connected equipment is low, sound is
recorded at a low volume. When the sound is low when playing a
recorded tape, set the [CD/LINE IN] switch ( ) on the rear panel
to “HIGH”and try recording again.
Recording from an externally connected CD
player etc.
Recording through the
built-in microphone (MIC)
B
Recording from an externally connected CD
player etc.
A
NORMAL HIGH
CD/LINE IN
a
SELECTOR
CD/
LINE IN
RADIO
TAPE/
34
21
CD/LINE IN
SELECTOR
CD/
LINE IN
RADIO
TAPE/
1
23
MIC
XBS
HEAVY
VOCAL SOFT
FLAT CLEAR
MIN MAX
PHONES
CD player,etc.
White (L)
Red (R)
Stereo connection cable
A
RX-CS40RQT763504.2.610:30ページ9

Troubleshooting guide
10
RQT7635
Before requesting service, make the below checks. If you can’t fix the system as described below, or if something not listed here occurs, consult
your dealer for instructions.
Reference pages are shown as black circled numbers .
Common Problems
No sound. Turn the volume up.
The speaker cords may be shorted. Turn the unit off, check and correct the connections and turn the
unit on.
No operation when powered by
batteries. •Replace with new batteries.
•Align the and polarities properly when inserting the batteries.
•Disconnect the AC power cord when powered by batteries.
Listening to the radio
Noise is heard.
Sound is distorted. Change the antenna or unit’s direction.
A beat sound is heard. •Turn the TV off or separate it from the unit.
•Separate the antenna from other cables and leads.
The cassette deck
Poor quality sound. Clean the heads.
Recording is not possible. If the erasure prevention tabs have been removed, cover the holes with adhesive tape.
Volume recorded on the tape is
low.
Not ejected or closed. Use the AC power supply cord or insert fresh batteries, and press [ PLAY], then press
[ STOP/EJECT].
Set the [CD/LINE IN] switch on the rear panel of this unit to HIGH and try recording again.
RX-CS40RQT763504.2.610:30ページ10