Panasonic SA-AK310GC User manual

Service Manual
TOP NEXT
ORDER NO. MD0212275C3
CD Stereo System
 SA-AK310GC
SA-AK310GN
Colour
(S)... Silver Type
TAPE SECTION :
SG-2W MECHANISM SERIES
Specifications
AMPLIFIER SECTION
Power output
10% Total harmonic distortion
1kHz, both channels driven
(Low channel) 55 W per channel (6Ω)
10kHz, both channels driven
(High channel) 55 W per channel (6Ω)
Total Bi-Amp power 110 W per channel
Input sensitivity
AUX 250 mV
Input Impedance
AUX 13.3 kΩ
FM TUNER SECTION
Frequency range 87.50 - 108.00 MHz (50 kHz steps)
Sensitivity 2.5µV (IHF)
S/ N 26 dB 2.2µV
Antenna terminal(s) 75Ω(unbalanced)
AM TUNER SECTION
Frequency range 522 - 1629 kHz (9 kHz steps)
520 - 1630 kHz (10 kHz steps)

© 2002 Matsushita Electronics (S) Pte. Ltd. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Sensitivity
S/ N 20 dB (at 999 kHz) 560µV/ m
CASSETTE DECK SECTION
Track system 4 track, 2 channel
Heads
Record/ playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100 kHz
Erasing system AC erase 100 kHz
Tape speed 4.8 cm/ s (1 7/ 8 ips)
Overall frequency response (+ 3 dB, -6 dB at DECK OUT)
NORMAL (TYPE I) 35 Hz - 14 kHz
S/ N 50 dB (A weighted)
Wow and flutter 0.18% (WRMS)
Fast forward and rewind time Approx. 120 seconds with
C-60 cassette tape
CD SECTION
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source/ wave length Semiconductor laser/ 780 nm
Number of channels Stereo
Frequency response 20 Hz - 20 kHz (+ 1, -2 dB)
Wow and flutter Below measurable limit
Digital filter 8 fs
D/ A converter MASH (1 bit DAC)
GENERAL
Power Supply
For GC only AC 110/ 127/ 220-230/ 240 V, 50/ 60Hz
For GN only AC 230-240 V, 50Hz
Power consumption
For GC only 172 W
For GN only 170 W
Power Consumption in standby mode
For GC only 0.85 W
For GN only 0.5 W
Dimensions (W x H x D) 250 x 330 x 370 mm
Mass
For GC only 7.8 kg
For GN only 7.0 kg
SYSTEM
SC-AK310 (GC) Music center: SA-AK310 (GC)
Speaker: SB-AK310 (GC)
SC-AK310 (GN) Music center: SA-AK310 (GN)
Speaker: SB-AK310 (GC)
Notes:
1. Specifications are subject to change without notice. Mass and dimensions are aproximate.
2. Total harmonic distortion is measured by the digital spectrum analyzer.
3. The labels“ HIGH” and“ LOW” on the rear of the speakers refer to High frequency and Low frequency.

TOP
NEXT

1 Before Use
TOP PREVIOUS NEXT
Be sure to disconnect the mains cord before adjusting the voltage selector.
Use a minus(-)
screwdriver to set the voltage selector (on the rear panel) to the voltage setting for the
area in which the unit will be used. (If the power supply in your area is 117V or 120V, set to the
“127V” position.)
Note that this unit will be seriously damaged if this setting is not made correctly. (There is no
voltage selector for some countries, the correct voltage is already set.)
TOP
PREVIOUS
NEXT

2 Before Repair and Adjustment
TOP PREVIOUS NEXT
Disconnect AC power, discharge Power Supply Capacitors C520 and C540 through a 10Ω, 5W
resistor to ground.
DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may
destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
TOP
PREVIOUS
NEXT

3 Protection Circuitry
TOP PREVIOUS NEXT
The protection circuitry may have operated if either of the following conditions are noticed:
 No sound is heard when the power is turned on.
 Sound stops during a performance.
The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative
speaker connection wires are
“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the
amplifier are used.
If this occurs, follow the procedure outlines below:
1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.
Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off
and then on again.
TOP
PREVIOUS
NEXT

4 Accessories
TOP PREVIOUS NEXT
Remote control transmitter
FM indoor antenna
AC power supply cord (For GC only)
AC power supply cord (For GN only)
AM Loop antenna
Power plug adaptor
TOP
PREVIOUS
NEXT

5 Operation Procedures
TOP PREVIOUS NEXT
TOP
PREVIOUS
NEXT

6 Handling Precautions For Traverse Deck
TOP PREVIOUS NEXT
The laser diode in the traverse deck (optical pickup) may break down due to potential difference
caused by static electricity of clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
 Handling of traverse deck (optical pickup)
1.
Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive
to electrical shock.
2. The short land between the No.4(LD) and No.5(GND) pins on the flexible board (FFC) is
shorted with a solder build-up to prevent damage to the laser diode.To connect to the PC
board, be sure to open by removing the solder build-up, and finishthe workquickly.
3. Take care not to apply excessive stress to the flexible board (FFC).
4. Do not turn the variable resistor (laser power adjustment). It has already been adjusted.
 Grounding for electrostatic breakdown prevention
1. Human body grounding
Use the anti-static wrist strap to discharge the static electricity from your body.
2. Work table grounding
Put a conductive material (sheet) or steel sheet on the area where the traverse deck
(optical pickup) is placed, and ground the sheet.
Caution :
The static electricity of your clothes will not be grounded through the wrist strap. So, take care
not to let your clothes touch the traverse deck (optical pickup).
Caution when Replacing the Traverse Deck :
The traverse deck has a short point shorted with solder to protect the laer diode against
electroststics breakdown. Be sure to remove the solder from the short point before making
connections.

TOP
PREVIOUS
NEXT