Panasonic SAPM08 - SINGLE DVD MINI SYST User manual

ORDERNo.MD0007129C3
DVDStereoSystem
SA-PM08
Colour
(S)................. SilverType
Areas
(GCS)............ Asia
(GK).............. China
CD SECTION:DPT-4AT-ADTRAVERSE DECK SERIES
SYSTEM:SC-PM08
SPECIFICATIONS
Specifications
1

AMPLIFIERSECTION
Frontspeakerpoweroutput
RMSpoweroutput
THD 10%, both channelsdriven
Front(HIGH) 10W perchannel (6 )
Front(LOW) 10W perchannel (6 )
Total bi-amp power 20W perchannel
Poweroutputin SSS mode
RMSpoweroutput
THD 10%, both channelsdriven
Front(HIGH) 10W perchannel (6 )
Front(LOW) 10W perchannel (6 )
Center(at1kHz) 10W (6 )
Surround (at1kHz) 10W perchannel (6 )
Total poweroutput 70W
/ Inputsensitivity
AUX 250mV
Inputimpedance
AUX 30k
FMTUNERSECTION
Frequencyrange 87.50 -108.00MHz/ (50kHz
step)
Sensitivity 1.8 V(IHF)
Antennaterminals 75 (unbalanced)
AMTUNERSECTION
Frequencyrange 522 -1629kHz(9kHzstep)
520 -1630kHz(10kHzstep)
Sensitivity
S/N20dBat999kHz 500 V/m
DISCSECTION
Disc
DVD-Video
8cm/12cm single-sided, single-layer/ 8cm/12cm single-
sided, double-layer/ 8cm/12cm double-sided, double-layer
/ (Onelayerperside)
Video CD/CD 8cm/12cm
Video
Signel system NTSC/PAL / (decided by
disc format)
Outputlevel Compositevideo 1Vp-p (75
)
S-VIDEOY 1Vp-p (75 )
S-VIDEOC 0.300Vp-p (75 /PAL)/
0.286Vp-p (75 /NTSC)
Audio
2

Sampling frequency
CD 44.1kHz
DVD 48kHz/96kHz
Decoding 16/20/24bitlinear
Wowand flutter Belowmeasurablelimit
Digital filter 8fs
D/Aconverter Delta-sigma DAC
Pick up
Beam Source SemiconductorLaser
Wavelength 665nm
GENERAL
Powersupply
For[GCS] area AC230 -240V, 50/60Hz
For[GK]area AC220V, 50Hz
Powerconsumption 85W
Dimensions(WxHxD) 250x131x323mm
Mass 5.2kg
Powerconsumption in standbymode Approx. 0.6W
Notes:
1. Specificationsaresubjectto changewithoutnotice. / Mass
and dimensionsareapproximate.
2. Total harmonicdistortion ismeasured bythedigital spectrum
analyzer.
*1Manufactured underlicense fromDolbyLaboratories
Licensing Corporation. “Dolby”, “AC-3”, “Pro Logic”and
thedouble-Dsymbol aretrademarks ofDolbyLaboratories.
SYSTEM
SC-PM08 :/ Main unit:SA-PM08
/ Frontspeakers:SB-PM08 /
Surround speakers:SB-PS80 /
CenterSpeakers:SB-PC80
1. BeforeRepairand adjustment
DisconnectACpower, dischargePowerSupplyCapacitorsC954 and C955 through a10 , 5W
resistor toground. / DONOTSHORT-CIRCUITDIRECTLY(withascrewdriverblade, for
3

instance), as thismay destroysolidstatedevices. / Afterrepairsarecompleted, restorepower
graduallyusing avariac, toavoidovercurrent. / Currentconsumption atAC230V, 50HzinNO
SIGNALmodeshouldbeless than300mA.
2. Protection Circuitry
Theprotection circuitrymay have operatedifeitherofthefollowing conditionsarenoticed:
-Nosound isheardwhenthepoweristurnedon.
-Sound stopsduring aperformance.
Thefunction ofthiscircuitryistopreventcircuitrydamageif, for example, thepositive and
negative speakerconnection wires are“shorted”, or ifspeakersystemswithanimpedance less
thantheindicatedratedimpedance oftheamplifierareused. / Ifthisoccurs, followtheprocedure
outlines below:
1. Turnoff thepower.
2. Determinethecause oftheproblemand correct it.
3. Turnon thepoweronce againafteroneminute.
Note:
Whentheprotection circuitryfunctions, theunitwill notoperate
unless thepowerisfirst turnedoff and thenon again.
3. Accessories
4. Handling Precautions forTraverse Deck
Thelaserdiodes inthetraverse deck (optical pickup)may break downduetopotential difference
causedbystaticelectricityofclothes or humanbody. / So, becareful ofelectrostaticbreakdown
during repairofthetraverse deck (optical pickup).
4.1. Handling thetraverse deck / (optical pickup)
1. Thetraverse deck (optical pickup)isanextremelyhigh-precision
construction and must notbesubjectedtoimpact, excessive
vibration, orothertypes ofrough handling.
4

2. Inordertopreventstaticelectricitydamagetothelaserdiode, use
ashortpinorsimilartool toshorttheoptical pickup’sflexible
circuitboardsaftertheyhavebeendisconnectedfromthemain
circuitboard.
3. Handletheflexiblecircuitboardswithcare;excessiveforce could
cause themtobebroken.
4. Donotturnthepre-set variableresistor(foradjustmentofthe
laserpower);ithas beenadjustedat thefactory. / (as shownin
Fig.1 )
Fig.1
4.2. Grounding forelectrostaticbreakdownprevention
1. Humanbodygrounding / Use theanti-ataticwrist strapto
dischargethestaticelectricityfromyourbody.
2. Worktablegrounding / Putaconductivematerial (sheet) orsteel
sheet on thearea wheretheoptical pickup isplaced, and ground
thesheet. (sa shownin Fig.2 )
Fig.2
5

Caution:
Thestaticelectricityofyourclothes will notbegroundedthrough
thewrist strap. / So, take carenottolet yourclothes touchthe
traverse deck (optical pickup)
4.3. Caution whenReplacing theTraverse Deck
Thetraverse deck has ashortpointshortedwithsolderprotectthelaserdiodeagainst
electrostaticbreakbown. Besuretoremove thesolderfrom theshortpointbeforemaking
connections.
CAUTION:
THISPRODUCTUNTILIZES ALASER. USE OFCONTROLSOR
ADJUSTMENTSORPERFORMANCEOFPROCEDURES OTHER
THANTHOSE SPECIFIEDHEREINMAYRESULT INHAZARDOUS
RADIATIONEXPOSURE.
5. Precaution of LaserDiode
6

6. Location of Controls
7. Location of ControlsforRemoteControl
7

Transmitter
8. Operation Checks and Component Replacement
Procedures
-Thissection describes procedures forchecking theoperation of
themajorprintedcircuitboardsand replacing themain
components.
-Forreassemblyafteroperation checks orreplacement, reverse the
respectiveprocedures. Special reassemblyprocedures are
describedonlywhenrequired.
8.1. Checking forthemainP.C.B., powersupplyP.C.B. and system
control P.C.B.
8

-Check themainP.C.B., powersupplyP.C.B. and systemcontrol
P.C.B. (Aside) as shownbelow.
9

-Check thesystemcontrol P.C.B. (Bside) as shownbelow.
8.2. Checking fortheDVDmodule(1) P.C.B. and micecho P.C.B.
-Follow the(Step1) -(Step12) ofitem8.1.
10