Panasonic SC-AK521 User manual

RQT7418-2M
G0104TS2034
CD Stereo System
Operating Instructions
Model No. SC-AK521
Before connecting, operating or adjusting this product, please read these
instructions completely.
Please keep this manual for future reference.
GCPPL
PL
:For areas using power supply of 120 V.
GCP :For areas using power supply of 110/127/220-230/240 V.
En Sp

RQT7418
2
ENGLISH
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions
carefully.
These operating instructions are applicable to the following systems.
Unless otherwise indicated, illustrations in these operating instructions
are of SC-AK521:
GCP
.
System SC-AK521
Main unit SA-AK521
Front speakers SB-AK520
Subwoofer SB-WAK520
IMPORTANT SAFETY INSTRUCTIONS............................. 3
Supplied accessories ........................................................ 4
Placement of speakers...................................................... 4
The remote control ............................................................ 4
Disc information ................................................................ 5
Set-up ................................................................................. 6
Front panel controls .......................................................... 7
CDs ..................................................................................... 8
How discs with MP3 differ from CDs ............................... 9
CD Play Mode function for MP3.......................................9
Album skip play.............................................................. 10
Track skip play ............................................................... 10
INTRO function (Album scan) ........................................ 10
Program play for MP3 .................................................... 10
Starting play from a desired track in a desired album .... 11
Title search function ....................................................... 11
CD display for MP3 ........................................................ 12
Marking a track .............................................................. 12
Radio ................................................................................ 13
Cassettes.......................................................................... 14
Sound quality/sound field ............................................... 15
KARAOKE ........................................................................ 15
Other functions ................................................................ 16
Optional antenna connections ........................................ 16
External unit connections ............................................... 16
Using an external unit .................................................... 17
Using headphones (not included)................................... 17
Turning the demo function on/off.................................... 17
Convenient functions ...................................................... 17
Auto-off function ............................................................. 17
Setting the time .............................................................. 17
Timers............................................................................... 18
Troubleshooting guide .................................................... 19
Maintenance ..................................................................... 19
Specifications .................................................................. 20
Table of contents
Inside of product
GCP only

RQT7418
3
ENGLISH
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR PRODUCT DAMAGE, DO NOT EXPOSE THIS
APPARATUS TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED
ON THE APPARATUS.
Read these operating instructions carefully before using the unit. Follow
the safety instructions on the unit and the applicable safety instructions
listed below. Keep these operating instructions handy for future
reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9)
PL only
Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused
for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally,
or has been dropped.
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORM-
ANCE OF PROCEDURES OTHER THAN THOSE SPECI-
FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOUR-
SELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION!
•DO NOT INSTALL OR PLACE THIS UNIT IN A
BOOKCASE, BUILT-IN CABINET OR IN ANOTHER
CONFINED SPACE. ENSURE THE UNIT IS WELL
VENTILATED. TO PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION
VENTS.
•DO NOT OBSTRUCT THE UNIT’S VENTILATION
OPENINGS WITH NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
•DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH
AS LIGHTED CANDLES, ON THE UNIT.
•DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY
FRIENDLY MANNER.
THIS UNIT IS INTENDED FOR USE IN TROPICAL
CLIMATES.
CAUTION:
Change the voltage setting to suit the AC voltage
in your area. See page 6.
Note that the unit will be seriously damaged or fail
to operate correctly if this setting is not made
correctly.
The socket outlet shall be installed near the equipment and
easily accessible or the mains plug or an appliance coupler
shall remain readily operable.
This product may receive radio interference caused by mobile tele-
phones during use. If such interference is apparent, please increase
separation between the product and the mobile telephone.
GCP only

RQT7418
4
ENGLISH
Batteries
The remote control
Aim at the sensor, avoiding obstacles, at a maximum range of 7
meters directly in front of the unit.
•Keep the transmission window and the unit’s sensor free from dust.
•Operation can be affected by strong light sources, such as direct
sunlight, and the glass doors on cabinets.
Do not:
•put heavy objects on the remote control.
•take the remote control apart.
•spill liquids onto the remote control.
•Insert so the poles (+ and –) match those in the remote control.
•Do not use rechargeable type batteries.
Do not:
•mix old and new batteries.
•use different types at the same time.
•heat or expose to flame.
•take apart or short-circuit.
•attempt to recharge alkaline or manganese batteries.
•use batteries if the covering has been peeled off.
•keep together with metallic objects such as necklaces.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
Remove if the remote control is not going to be used for a long
period of time. Store in a cool, dark place.
Replace if the unit does not respond to the remote control even
when held close to the front panel.
Use
R6/LR6, AA, UM-3
Remote control
signal sensor
Transmission
window About 7 meters in front of
the signal sensor
Placement of speakers
Place the front speakers so that the super tweeter is on the outside.
Note
•Keep your speakers at least 10 mm away from the system for
proper ventilation.
•These speakers do not have magnetic shielding. Do not place them
near televisions, personal computers or other devices easily
influenced by magnetism.
•You cannot take the front net off the speakers.
FM indoor
antenna................ 1 pc.
Batteries for
remote control .. 2 pcs.
AC power supply cord .....................................1 pc.
Supplied accessories
Please check and identity the
supplied accessories.
AM loop
antenna................ 1 pc.
GCP only
Power plug
adaptor ................ 1 pc.
Remote control transmitter.............................. 1 pc.
(N2QAHB000039)
M
E
M
O
R
Y
30
˚
30
˚
PL GCP
Main unit
Front speaker
(left) Front speaker
(right)
Super tweeter Super tweeter
Place on the floor or a sturdy shelf
so that it won’t cause vibration.
(SB-WAK520)
Subwoofer

RQT7418
5
ENGLISH
Disc information
Choose CDs with this mark:
Do not:
•use irregularly shaped CDs.
•attach extra labels and stickers.
•use CDs with labels and stickers
that are coming off or with
adhesive exuding from under
labels and stickers.
•attach scratch proof covers or
any other kind of accessory.
•write anything on the CD.
•clean CDs with liquids. (Wipe
with a soft, dry cloth.)
•use CDs printed with label
printers available on the market.
Always observe the following points:
•Load only 1 CD on the tray.
•Load CDs as shown in the figure.
An adaptor is not needed with 8 cm CDs (singles).
•Set the system on a flat, level surface.
•Always unload all CDs before moving the unit.
Do not:
•set the unit on top of magazines, inclined surfaces, etc.
•move the unit while a tray is opening/closing, or when loaded.
•put anything except a CD in the tray.
•use cleaning CDs or CDs which are badly warped or cracked.
•disconnect the AC power supply cord from the household AC outlet
during disc changing operation.
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
XXXXXXXX XXXXX XXXXXX
XXXXXXXX XXXXX
XXXXXXXX XXXXX
XXXXXXXX
XXXXXXXXX XXXXXXX
XXXXXX XXXXX
XXXXXX XXXXX
XXXXXXXX XXXXX
XXXXXX XXXXX
XXXXXXXX XXXXX
XXXXXXXXX XXXXXXX
XXXXXX XXXXX
XXXXXX XXXXX
XXXXXXXX XXXXX
XXXXXX XXXXX
XXXXXXXX XXXXX
XXXXXXXXXXX
XX
XXXXXXXXXXXX
XXXXXXX
XXXX
XXXXXXX
XXXX
XXXXXXX
XXXX
XXXXXX XXXXX
XX
XXXXXXXXXXXX
XXXXXXX
XXXX
XXXXXXX
XXXX
XXXXXXX
XXXX
8 cm CD
12 cm CD
CD selection
To prevent damage
This unit can play MP3 files recorded on CD-R/RW with a computer.
Files are treated as tracks and folders are treated as albums.
This unit can access up to 999 tracks, 255 albums and 20 sessions.
When making MP3 files to play on this unit
Disc format
Discs must conform to ISO9660 level 1 or 2 (except for extended
formats).
File format
MP3 files must have the extension “.MP3” or “.mp3”.
To play in a certain order
Prefix the folder and file names with 3-digit numbers in the order you
want to play them.
Files may not be recorded in numbered order if the prefixes have
different numbers of digits. For example: 1????.mp3, 2????.mp3,
10????.mp3.
However, some writing software may also cause recording to occur in
a different order.
MPEG Layer-3 audio decoding technology licensed from Fraunhofer
IIS and Thomson multimedia.
Limitations on MP3 play
•This unit is not compatible with packet-write format.
•When both MP3 and CD-DA data is recorded on the disc over a
number of sessions:
•If the first session contains MP3 recordings, the unit will play
from the MP3 made in that session till the session before the first
CD-DA recordings.
•If the first session contains CD-DA recordings, the unit will play
only the recordings made in that session. The subsequent
sessions will be ignored.
•Some MP3 may not be played due to the condition of the disc or
recording.
•Recordings will not necessarily be played in the order you recorded
them.
MP3 information
This unit can play MP3 and CD-DA (digital audio) format audio
CD-R and CD-RW that have been finalized (a process that enables
CD-R/CD-RW players to play audio CD-R and CD-RW) upon
completion of recording.
It may not be able to play some CD-R or CD-RW due to the
condition of the recording.
root
001
002
003
001.mp3
002.mp3
003.mp3
001.mp3
002.mp3
003.mp3
004.mp3
001.mp3
002.mp3
003.mp3

RQT7418
6
ENGLISH
2 AM loop antenna
Stand the antenna up
on its base.
(R) (L)
1 FM indoor antenna
Adhesive tape
Affix where
reception is best.
To household
AC outlet
Voltage selector
Use a flat-head screwdriver to turn the voltage
selector on the rear panel to the appropriate
position for the area in which this system is
used. If the power supply in your area is
115 V or 120 V, please set the voltage
selector as follows:
•For 115V: Set to 110 V.
•For 120V: Set to 127 V.
VOLT ADJ
4GCP
only
Set-up
Connect the AC power supply cord only after all other connections have been made.
Preparation
Twist and pull off the vinyl tip of the antenna wires and speaker cords.
3Speaker cords
Use only the supplied speakers.
The combination of the main unit and speakers provide the best sound. Using
other speakers can damage the unit and sound quality will be negatively affected.
5AC power supply cord
Note
The included AC power supply cord is for use
with this unit only. Do not use it with other
equipment.
For your reference
To save power when the unit is not to be used for
a long time, unplug it from the household AC outlet.
You will need to reset some memory items after
plugging in the unit.
Insertion of connector
Even when the connector is perfectly inserted,
depending on the type of inlet used, the front
part of the connector may jut out as shown in the
drawing.
However there is no problem using the unit.
GCP only
If the power plug does not fit your socket, use
the power plug adaptor (included).
Connector
Appliance inlet
Approx. 6 mm
Gray (+)
Red (+)
Blue
Gray
Black (–)
Blue (–)
Red
Red
Black Red (+)
Black (–)
Subwoofer
(SB-WAK520)
-
1
3
Connect the left (L)
side in the same way.
Black
Caution
•Use the speakers only with the recommended system.
Failure to do so may lead to damage to the amplifier
and/or the speakers, and may result in the risk of fire.
Consult a qualified service person if damage has
occurred or if you experience a sudden change in
performance.
•Do not attach these speakers to walls or ceilings.

RQT7418
7
ENGLISH
1AC supply indicator [AC IN]
This indicator lights when the unit is connected to the AC mains
supply.
2
PL
Standby/on switch [ff
ff
f/I, POWER]
Press to switch the unit from on to standby mode or vice versa. In
standby mode, the unit is still consuming a small amount of power.
GCP
Standby/on switch [ff
ff
f/I]
Press to switch the unit from on to standby mode or vice versa. In
standby mode, the unit is still consuming a small amount of power.
3Display
4Microphone jack [MIC] ...........................................................15
5Deck 1 cassette holder ......................................................... 14
6Disc tray
7CD tray open/close button [c, OPEN/CLOSE]...................... 8
8CD direct play buttons [1 ~ 5] ................................................ 8
9Remote control signal sensor ................................................ 4
!Headphones jack [PHONES] ................................................ 17
! Deck 2 cassette holder ......................................................... 14
Main unit
Center console
Remote control
Buttons such as 2function in exactly the same way as the
buttons on the main unit.
]Sleep timer + Auto off button [SLEEP, AUTO OFF] ......17, 18
^Disc button [DISC] .................................................................. 8
_Program button [PROGRAM] ..................................... 9, 10, 13
{Play mode select button [PLAY MODE].................... 8, 9, 13, 14
Use this for selecting CD play mode, tune mode, FM mode, AM
beat proof, tape reverse mode and deck select.
|Repeat button [REPEAT] ........................................................ 8
}Album skip buttons [ , , ALBUM] .................................... 9
VIntro button [INTRO] ............................................................. 10
0Shift button [SHIFT]
To use functions labeled in orange :
While pressing [SHIFT], press the corresponding button.
For buttons [AUTO OFF], [CLOCK/TIMER], [rPLAY/REC],
[S.WOOFER] and [KARAOKE]
1Super sound EQ + Subwoofer button
[S.SOUND EQ, S.WOOFER].................................................. 15
2Dimmer + Play timer/record timer button
[DIMMER, rPLAY/REC] ...................................................17, 18
3CD display + Clock/timer button
[CD DISP, CLOCK/TIMER] .................................... 8, 12, 17, 18
Numbered, character buttons
[
XX
XX
X 10, 1–9, 0, A-Z, SPACE!”#] ............................................. 8-13
5CD skip/search, tape fast-forward/rewind,
tune/preset channel select, time adjust, cursor buttons
[g, REW/3, CURSOR, f, 4/FF, CURSOR ] ... 8-14, 17
6Muting button [MUTING] ....................................................... 17
7Preset EQ select + karaoke button [PRESET EQ, KARAOKE] .. 15
Front panel controls
#Subwoofer button [SUBWOOFER]....................................... 15
$Super sound EQ button [SUPER SOUND EQ] .................... 15
%CD skip/search, tape fast-forward/rewind,
tune/preset channel select, time adjust buttons
[g/REW/3, f/FF/4]................................ 8-11, 13, 14, 17
&Tuner/band select button [TUNER, BAND].......................... 13
(CD play/pause button [:/J, CD] ........................................... 8
)Enter button [ENTER] ......................................................10, 11
~Joystick.............................................................................10, 11
+Microphone volume control [MIC VOL] ............................... 15
,Preset EQ select button [PRESET EQ] .................................15
-Deck 1 open button [c, DECK 1]......................................... 14
.Display, demonstration button [DISP, –DEMO] .................. 17
/Record button [a, REC] .........................................................14
:AUX button [AUX] ..................................................................17
;Volume control [VOLUME DOWN, UP] .................................15
<Tape play/direction button [;:, TAPE] .............................. 14
=Deck select button [DECK 1/2]..............................................14
>Stop/program clear button [L, STOP] ........................ 8-11, 14
?Deck 2 open button [c, DECK 2]......................................... 14
@Delete button [DELETE] .............................................. 9, 10, 12
[Title search mode select button [TITLE SEARCH].................11
\Marker memory/recall button
[MARKER, –MEMORY, -RECALL] ........................................ 12
!
44

RQT7418
8
ENGLISH
To listen to specific CDs and tracks
(CD Play Mode function)
Remote control only
Preparation: Press [:/J, CD] and then [L, CLEAR].
1Press [PLAY MODE] to select the desired mode.
Every time you press the button:
ALL-DISC 1-RANDOM1-SONG
1-DISC
A-RANDOM
ALL-DISC: Plays all loaded discs in succession from the
selected disc to the final disc .
1-SONG: Plays one selected track on the selected disc.
1-RANDOM: Plays one selected disc in random order.
A-RANDOM: Plays all loaded discs in random order.
1-DISC: Plays one selected disc.
(The original display is restored in about 2 seconds.)
Proceed to step 4 when you selected A-RANDOM in step 1.
2Press [DISC] and (within 10 seconds) [1]–[5] to select the
disc.
The CD starts.
3Only when you selected “1-SONG” in step 1
Select the track with the numbered buttons.
To select a track 10 or over, press [ X 10] then the two digits.
Play starts from the selected track.
4Only when you selected “A-RANDOM” in step 1
Press [:/J, CD] to start play.
To stop play
Press [L, CLEAR].
When playback ends
The current play mode will be retained in memory until it is changed
even if the unit is turned off.
Final disc
For example, if play starts from disc 4, disc 3 will be the “final disc”.
Order of progression: Disc 4z5z1z2z3
Note
•You can use repeat mode with CD Play Mode function.
•You cannot use program mode together with CD Play Mode function.
1Press [c, OPEN/CLOSE] to open the tray.
The unit comes on.
2Set a CD in the tray. (Label must face upward.)
To continue loading CDs in the other trays
Press [1]–[5] to select the required tray and press [c, OPEN/
CLOSE] to open the tray.
Press [c, OPEN/CLOSE] to close the tray.
3Press [1]–[5] to play your desired disc.
(Alternatively, you can press [:/J, CD] if the current disc is your
desired CD.)
The track number and its elapsed playing time are shown.
Use the CD Play Mode function’s ALL-DISC mode to play CDs in
succession. (A see right)
To stop the disc play
Press [L, STOP].
The total number of tracks and total playing time are shown.
One touch play
During standby mode and when a CD is loaded, press [:/J, CD] or
[1] – [5].
The unit comes on and play starts.
To pause Press [:/J, CD] during play.
Press again to resume play.
To search forward/ Hold down [g/REW/3] (backward)
backward or [f/FF/4] (forward) during play or pause.
To skip forward/ Press [g/REW/3] (backward) or
backward [f/FF/4] (forward) during play or pause.
CDs
Note
•During 1-RANDOM or A-RANDOM play (A see below), you cannot
skip to tracks already played.
•During program play (A page 9), 1-RANDOM or A-RANDOM play,
you can search only within the track.
•You cannot use search function for MP3 files.
•Always stop the changer before loading or changing CDs. You
cannot change CDs while a disc is playing.
CD display
You can display the remaining play time of the current track.
Press [CD DISP] on the remote control during play or pause.
Every time you press the button:
Elapsed play time ↔Remaining play time
Note
When track number 25 or greater is playing, remaining play time
display shows “– –:– –”.
Repeat play
Remote control only
Press [REPEAT] during play.
“” is displayed.
To cancel repeat play
Press [REPEAT] to clear “ ” .
Basic play
Current disc indicator
5
3
12
4
c, OPEN/CLOSE
CD direct
play 1~5
L, STOP
CD DISP
Numbered
buttons
-/J, CD
L, CLEAR
g , REW/3,
f , 4/FF
DISC 1-5
PROGRAM
PLAY MODE
REPEAT
DEL
ALBUM ( or )
-/J, CD
g /REW/3,
f /FF/4

RQT7418
9
ENGLISH
Program play
You can program up to 24 tracks.
Remote control only
Preparation: Press [::
::
:/JJ
JJ
J, CD] and then [L, CLEAR].
Press [PROGRAM].
“PGM” appears.
Press [DISC] and (within 10 seconds) [1]–[5] to select the
disc.
Select the tracks with the numbered buttons.
To select track 10 or over, press [ X 10] then the two digits.
Repeat steps 2 and 3 to program other tracks.
Press [:/J, CD] to start play.
To exit program mode
Press [PROGRAM] in the stop mode. (You can replay your program
by pressing [PROGRAM] then [:/J, CD].)
You can do the following while “P”is displayed
•To check program contents
Press [g, REW/3] or [f, 4/FF].
Every time you press the button, the track number and program
order are displayed.
•To add to the program
Do steps 2 and 3.
•To clear the last track
Press [DEL].
•To clear all tracks
Press [L, CLEAR].
While “CLEAR ALL” is blinking, press the button again to clear all tracks.
Note
•You can use repeat mode with program play.
•You cannot program CD-DA together with MP3 tracks.
To mark a track
See page 12.
1
2
3
4
CD Play Mode function for MP3
Remote control only
Preparation: Press [:/J, CD] and then [L, CLEAR].
1Press [PLAY MODE] to select the desired mode.
Every time you press the button:
ALL-DISC 1-ALBUM1-SONG
1-DISC
ALL-DISC: Plays all loaded discs in succession from the
selected disc to the final disc .
1-SONG: Plays one selected track on the selected disc.
1-ALBUM: Plays one selected album on the selected disc.
1-DISC: Plays one selected disc.
(The original display is restored in about 2 seconds.)
2Press [DISC] and (within 10 seconds) [1]–[5] to select the
disc.
The CD starts.
3When you selected “1-ALBUM”or “1-SONG”in step 1
Press [ALBUM ( or )] to select the album.
Play starts from the first track of the selected album.
4When you selected “1-SONG”in step 1
Press the numbered buttons to select the track in the
current album.
To select track 10 or over, press [ X 10] once then the two digits.
To select track 100 or over, press [ X 10] twice then the three digits.
Play starts from the selected track.
To stop play
Press [L, CLEAR].
LDisplay when in the stop mode (example)
File format indicator
“MP3”: Indicates the disc contains MP3 files
Starting play from a specific track
Remote control only
1Press [DISC] and (within 10 seconds) [1]–[5] to select the
disc.
2Select the track with the numbered buttons.
To select track 10 or over, press [ X 10] then the two digits.
Play starts from the selected track.
Note
You cannot use this function with 1-RANDOM or A-RANDOM mode.
CDs
How discs with MP3 differ from CDs
When playback ends
The current play mode will be retained in memory until it is changed
even if the unit is turned off.
Final disc
For example, if play starts from disc 4, disc 3 will be the “final disc”.
Order of progression: Disc 4z5z1z2z3
LWhen “NOT MP3/ERROR1”appears on the display
An unsupported MP3 format is being played. The unit will skip that
track and play the next one.
Note
•You can use repeat mode (A page 8) with CD Play Mode function.
•You cannot use program mode together with CD Play Mode function.
Total number of tracks
(on the current disc)
Total number of albums
(on the current disc)
File format indicator
Track number Program order

RQT7418
10
ENGLISH
Album skip play
During play or stop
Push the joystick up/down ([ALBUM /CHARA] or
[ALBUM /CHARA]) to select the desired album.
Remote control: Press [ALBUM ( or )].
When selecting in the stop mode:
Press [:/J, CD] to start play.
Play starts from the first track of the selected album.
To play from another track, refer to “Track skip play” below.
Track skip play
During play or stop
Push the joystick left/right ([ g, CURSOR] or [f,
CURSOR]) to select a desired track. (You can also press
[ g/REW/3] or [f/FF/4].)
Remote control: Press [g, REW/3] or [f, 4/FF].
When selecting in the stop mode:
Press [:/J, CD] to start play.
Play starts from the selected track.
To play from another album, refer to “Album skip play” above.
Note
During 1-ALBUM mode, track skipping can only be done within the
current album.
Program play for MP3
You can program up to 24 tracks.
Remote control only
Preparation:
1. Press [DISC] and (within 10 seconds) [1]–[5] to select the disc.
2. Press [L, CLEAR].
1Press [PROGRAM].
“PGM” appears.
2Press [ALBUM ( or )] to select the album.
To select an album directly, press the numbered buttons
after pressing [ALBUM ( or )].
To select album 10 or over, press [>10] once then the two digits.
To select album 100 or over, press [>10] twice then the three digits.
3Press [ g, REW/3] or [f, 4/FF] to select the track.
To select a track directly, press the numbered buttons after
pressing [ g, REW/3] or [f, 4/FF].
To select track 10 or over, press [>10] once then the two digits.
To select track 100 or over, press [>10] twice then the three digits.
4Press [ENTER].
Repeat steps 2~4 to program other tracks.
5Press [:/J, CD] to start play.
To exit program mode
Press [PROGRAM] in the stop mode. (You can replay your program
by pressing [PROGRAM] then [:/J, CD].)
You can do the following while “P” is displayed
•To check program contents
Press [g, REW/3] or [f, 4/FF].
Every time you press the button, album number, track number and
program order are displayed.
•To add to the program
Do steps 2~4.
•To clear the last track
Press [DEL].
•To clear all tracks
Press [L, CLEAR].
While “CLEAR ALL” is blinking, press the button again to clear all
tracks.
Note
•You can use repeat mode (A page 8) with program play.
•You cannot program more than one CD for MP3.
•You cannot program CD-DA together with MP3 tracks.
•The program memory is cleared when you change a disc or open
the CD tray.
How discs with MP3 differ from CDs
INTRO function (Album scan)
You can find an album by listening to the first track of all albums in the
current disc for 10 seconds each.
Remote control only
Preparation: Press [:/J, CD] and then [L, CLEAR].
1Press [INTRO].
INTRO function starts.
(INTRO function is cancelled after playing the first track in the
last album on the current disc.)
2While your desired album is playing, press [::
::
:/J, CD].
Play continues from the first track of the album.
To stop during the process, press [INTRO] or [L, CLEAR].
Current album Number of tracks
in current album
Current album Current track
-/J, CD
L, CLEAR
g , REW/3,
f , 4/FF
ENTER
TITLE SEARCH
Numbered
buttons
g /REW/3,
f /FF/4
DISC 1-5
PROGRAM
DEL
-/J, CD L, STOP
ENTER
Joystick
TITLE SEARCH
ALBUM ( or )
INTRO

RQT7418
11
ENGLISH
Starting play from a desired track in a
desired album
Remote control only
Preparation: Press [:/J, CD] and then [L, CLEAR].
1Press [ALBUM ( or )] and then the numbered
buttons to select the album.
To select album 10 or over, press [>10] once then the two digits.
To select album 100 or over, press [>10] twice then the three
digits.
Play starts from the first track of the selected album.
2Press the numbered buttons to select the track in the
current album.
To select track 10 or over, press [>10] once then the two digits.
To select track 100 or over, press [>10] twice then the three digits.
Play starts from the selected track.
Title search function
You can search for your desired album/track with its keyword (part of
the title).
Album title search
Preparation: Press [:/J, CD] and then [L, STOP].
1Press [TITLE SEARCH] once.
2Enter the characters of the keyword for the album
title. (Asee right: “Entering characters”)
3Press [ENTER].
Album title search starts.
To show the next/previous album title search result
Push the joystick right ([f, CURSOR]) (next) or left ([g,
CURSOR]) (previous). (You can also press [ g/REW/3] or
[f/FF/4].)
Remote control: Press [f, 4/FF] (next) or [g, REW/3]
(previous).
Press [:/J, CD] to start play from the album found.
Play starts from the first track of the album.
(Title search mode is cancelled.)
To cancel partway through
Press [L, STOP].
When there is no match for the searched keyword, the display shows
“NOT FOUND”.
Note
You cannot use title search function in program mode.
(Continued on next page)
Track title search
Preparation: Press [:/J, CD] and then [L, STOP].
1Press [TITLE SEARCH] twice.
2Enter the characters of the keyword for the track title.
(Asee below: “Entering characters”)
3Press [ENTER].
Track title search starts.
To show the next/previous track title search result
Push the joystick right ([f, CURSOR]) (next) or left ([g,
CURSOR]) (previous). (You can also press [ g/REW/3] or
[f/FF/4].)
Remote control: Press [f, 4/FF] (next) or [g, REW/3]
(previous).
Press [:/J, CD] to start play from the track found.
(Title search mode is cancelled.)
To cancel partway through
Press [L, STOP].
When there is no match for the searched keyword, the display shows
“NOT FOUND”.
Note
You cannot use title search function in program mode.
Blinks to indicate album title search mode
Matched album title
Matched track title
Blinks to indicate track title search mode
Entering characters
You can enter keyword of up to 8 characters for album/track title
search. You can only enter upper case letters but the unit also searches
for lower case.
On the main unit
11
11
1Push the joystick up/down ([ALBUM /CHARA] or
[ALBUM /CHARA]) to select the required character.
Each time you push the joystick up ([ALBUM /CHARA]), the
characters change in the following order.
ABCDEFGHIJKLMNOPQRSTUVWXYZ
1234567890
space !”#$ %&’()∗+,– ./:;<= > ?_ `
The sequence is reversed if you push the joystick down
([ALBUM /CHARA]).
If you hold the joystick up/down ([ALBUM /CHARA] or
[ALBUM /CHARA]), the characters change faster.
22
22
2Push the joystick right ([f, CURSOR]) to enter the
character.
Repeat steps 1~2to complete the keyword.

RQT7418
12
ENGLISH
CD display for MP3
During play or pause
Press [CD DISP] on the remote control to select a desired
CD display mode.
Every time you press the button:
aRemaining play time, Original display
bElapsed play time, Album title
cElapsed play time, Track title
dElapsed play time, ID3 album name
eElapsed play time, ID3 title name
fElapsed play time, ID3 artist name
gElapsed play time, Original display
Example:
c
Note
•When a title is longer than 8 characters, it will scroll across the
display. If you selected a mode from b- f(see above), the
scrolling will start again after every 3 seconds.
•“NO ID3” is displayed if titles with ID3 tags haven’t been entered.
•Maximum number of displayable characters:
Album/track title: 31
ID3 album/title/artist name: 30
(ID3 is a tag embedded in MP3 track to provide information about
the track.)
•This unit can display album and track titles with ID3 tags (version
1.0 and 1.1). Titles containing text data that the unit doesn’t support
cannot be displayed.
•Titles entered with 2-byte code cannot be displayed correctly on this
unit.
To recall a marked track number in the current disc
During play or stop
Press [MARKER, -RECALL] to recall a marker.
Remote control: Press [MARKER].
Play starts from the track recalled.
Note
•“NO MARKER” indicates that the marker in the current disc is empty.
•The marker memory is cleared when you open the CD tray.
•For CD-DA, you cannot use this function during 1-RANDOM play
and A-RANDOM play.
•You cannot use this function during program mode.
Marking a track
You can mark one track each on the discs loaded so that you can
start play from them later.
To mark a track number
1During play or stop
Select your desired track.
(For MP3, refer to “Track skip play” on page 10.
For CD-DA, press the numbered buttons on the remote control.
To select track 10 or over, press [ X 10] then the two digits.)
2Hold down [MARKER, –MEMORY] until “STORING”
blinks on the display.
Remote control: Hold down [MARKER].
The selected track is stored in the marker of the current disc.
Note
If a track is already stored in the marker, it will be replaced next time
you store a new track in the same marker.
How discs with MP3 differ from CDs
22
22
2Press [CURSOR ]to enter the character.
Repeat steps 1~2to complete the keyword.
LEditing keywords
To move the cursor
Push the joystick left/right ([g, CURSOR] or [f, CURSOR]).
Remote control: Press [CURSOR ( or )].
Deleting a character
1. Move the cursor over the character to be deleted.
2. Press [DELETE] (remote control: Press [DEL].)
Editing a character
1. Move the cursor over the character to be edited.
2. Enter the correct character.
The characters change each time a numbered button is pressed.
For example, every time you press [2]:
A →B → C → 2
∧
Numbered Characters Numbered Characters
buttons buttons
1 1 6 M N O 6
2 A B C 2 7 P Q R S 7
3 D E F 3 8 T U V 8
4 G H I 4 9 W X Y Z 9
5 J K L 5 0 0
>10 space !”#$ %&’()∗+,–./:;<= > ?_ `
Title search function
TUNER, BAND
PROGRAM
PLAY MODE
DEL
TUNER, BAND
MARKER
Elapsed play time
Track title
→→→→→→
→
Entering characters
On the remote control
11
11
1Press the numbered button to select the required character.
Characters allocated to the numbered buttons:
g /REW/3,
f /FF/4
CD DISP
Numbered
buttons
CURSOR ( or )
g , REW/3,
f , 4/FF
Joystick
MARKER
–MEMORY
-RECALL
DELETE

RQT7418
13
ENGLISH
1Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button:
FM ↔AM
2Press [PLAY MODE] on the remote control to select
“MANUAL”.
Every time you press the button:
MANUAL ↔ PRESET
3Hold down [g/REW/3] or [f/FF/4] for a moment
to search for a station.
The frequency stops when it finds a clear station.
To stop during the process, press [g/REW/3] or [f/FF/4].
Under excessive interference, a station may not be found.
Press [g/REW/3] or [f/FF/4] repeatedly to tune step-by-
step.
“TUNED”is displayed when a radio station is tuned.
“ST”is displayed when a stereo FM broadcast is being
received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display “MONO”.
Monaural sound is selected and noise reduces when reception is
weak.
Hold down [PLAY MODE] again to cancel the mode.
“MONO”is also cancelled if the frequency is changed.
Allocation setting
Main unit only
PL
: By adjusting the allocation, you can enable this tuner to receive
FM broadcasts allocated in 0.1MHz steps.
GCP
: By adjusting the allocation, you can enable this tuner to receive
AM broadcasts allocated in 10 kHz steps.
Hold down [TUNER, BAND]. The display changes in a few seconds to
show the current minimum frequency. Continue to hold down the
button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
Note
•After changing the “allocation”setting, the frequencies you previously
preset in the memory will be cleared.
•Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.
Remote control only
There are two methods of pre-setting stations.
Automatic presetting : All the stations the tuner can receive are
preset.
Manual presetting : You can select the stations to preset and the
order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select “FM”or “AM”.
Automatic presetting
Do the following once each for FM and AM.
Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned in.
Manual presetting
Pre-set the stations one at a time.
1Press [PROGRAM] then press [g, REW/3] or
[f,4/FF] to tune to the desired station.
2Press [PROGRAM] then press [g, REW/3] or
[f,4/FF] to select a channel.
3Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
Selecting channels
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [ X 10], then the two digits.
OR
1Press [PLAY MODE] to select “PRESET”.
2Press [g, REW/3] or [f, 4/FF] to select the
channel.
Manual tuning Preset tuning
Radio

RQT7418
14
ENGLISH
You can use either deck 1 or deck 2 for tape playback.
Use normal position tapes.
High position and metal position tapes can be played, but the unit will
not be able to do full justice to the characteristics of these tapes.
1Press [;:, TAPE].
The unit comes on.
If a cassette was loaded, play starts automatically (One touch play).
2Press [c,DECK 1] or [c,DECK 2] and insert the
cassette.
Insert with the side to be played
facing towards you and the
exposed tape facing down.
Close the holder by hand.
3Press and hold [PLAY MODE] on the remote control to
select the reverse mode.
Every time you press and hold the button:
: One side is played.
: Both sides are played.
: Both sides are played repeatedly until [L, STOP] is
pressed.
To listen to 2 tapes consecutively
Load a tape into each deck and select “ ”. Both tapes will be
played repeatedly until [L, STOP] is pressed.
4Press [;:, TAPE] to start playback.
Every time you press the button: /R ↔F -
F -: The forward side (front side) will play.
/R : The reverse side will play.
To stop tape playback
Press [L, STOP].
To fast-forward or rewind
Press [g/REW/3] (rewind) or [f/FF/4] (fast-forward).
To select between loaded decks
Press [DECK 1/2] (remote control: [PLAY MODE]).
Cassettes
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this unit will
not be able to record or erase them correctly.
Preparation:
Wind up the leader tape so recording can begin immediately.
Press [;:, TAPE] then [L, STOP] to select tape as the source.
1Press [c, DECK 2] and insert the cassette to be
recorded.
The tape direction is automatically set to “F :”.
To record on the reverse side
Press [;:, TAPE] twice, then press [L, STOP]
2Press and hold [PLAY MODE] on the remote control to
select the reverse mode.
Every time you press and hold the button:
: One side only records.
,
: Both sides record (forward → reverse).
“ ” automatically changes to “ ” when [a, REC] is pressed.
3Select the source to be recorded.
Radio recording:
Tune in the station. (Apage 13)
CD recording:
1Insert the CD(s) you want to record.
Press [:/J, CD] and then [L, STOP].
2Prepare the desired CD recording mode.
Remote control only
•To record programmed tracks (Ado steps 1–3 on page 9
for CD-DA or steps 1–4 on page 10 for MP3).
•To record specific CDs/tracks
1. For CD-DA, do steps 1 to 2 on page 8: “To listen to
specific CDs and tracks (CD Play Mode function)”.
For MP3, do steps 1 to 2 on page 9: “CD Play Mode
function for MP3”.
Ensure CD is stopped.
2. (MP3 only) For 1-ALBUM mode and 1-SONG mode:
Press [ALBUM ( or )] to select the album.
3. For 1-SONG mode: Press [g, REW/3] or [f,
4/FF] to select the track.
Tape-to-tape recording:
1Press [;:, TAPE] and then [L, STOP].
2Press [c, DECK 1] and insert the cassette you want to record.
4Press [a, REC] to start recording.
To stop recording
Press [L, STOP].
If the tape finishes before the CD
The CD continues playing. Press [L, STOP] to stop it.
Reducing noise when recording AM
Remote control only
Hold down [PLAY MODE] while recording.
Every time you hold down the button: BP1 ↔BP2
Choose the setting with the least noise.
Note
•Changes to volume and sound/field quality do not affect recording.
•You cannot open deck 1 while recording.
•You cannot fast-forward or rewind one deck while recording with
the other.
•When recording an AM broadcast, sound is momentarily interrupted
when you start and stop the recording.
(Continued on next page)
Playback
Recording
Note
•Tape playback is momentarily interrupted if you open the other deck.
•Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
•Tape slack can get caught up in the mechanism and should be
taken up before the tape is played.
•Endless tapes can get caught up in the deck’s moving parts if used
incorrectly. Use tapes appropriate to this unit’s auto-reverse
mechanism.
Front side
VOL
VOL
VOL
VOL
7 8 9
0
10
6
SHI
SHI
FT
CLOCK
CLOCK
TIMER
TIMER
//
PL
PL
AY
REC
REC
AUTO OFF
O OFF
INTRO
INTRO
S.
S.
SO
SO
UND EQ
UND EQ
PRE
RE
SET EQ
T EQ
MUT
UT
ING
ING
ENTER
ENTER
MARKER
MARKER
TITLE
TITLE
SEARCH
SEARCH
REW FF
PROG
PROG
RAM
AM
REP
REP
EAT
AT
PLAY MODE
AY MODE
DISC
DISC
SPACE
SPACE
ABC
ABC
DEF
DEF
GHI
GHI
TUV
TUV
WXY
WXY
ZPQRS
PQRS
JKL
JKL
MNO
MNO
SLEEP
EEP
CD DISP
CD DISP
DIMMER
DIMMER
ALBUM
BUM
CURSOR
CURSOR
DEL
DEL
45
123
TAPE
TAPE
CD
CD
AUX
AUX
CLEAR
LEAR
TUNER
TUNER
BAND
ND
KARAOKE
KAR AOK E
L, STOP
g /REW/3,
f /FF/4
PLAY MODE
-/J, CD
c, DECK 2
DECK 1/2
/-, TAPE
g , REW/3,
f , 4/FF
KARAOKE,
PRESET EQ
SUPER
SOUND EQ
MIC VOL
PRESET EQ
c, DECK 1
[, REC
VOLUME
MIC
SHIFT
S.WOOFER,
S.SOUND EQ
ALBUM ( or )
SUBWOOFER
Microphone
(not included)

RQT7418
15
ENGLISH
Cassettes
Erasure prevention
Use a screwdriver or similar object to break out the tab.
To re-record on a protected cassette
Cover the hole with adhesive tape.
To erase a tape
1. Disconnect the microphone.
2. Press [;:, TAPE] and then [L, STOP].
3. Insert the recorded tape into deck 2.
Ensure there is no tape in deck 1.
4. Press and hold [PLAY MODE] on the remote control to select
reverse mode.
5. Press [a, REC].
Sound quality/sound field
Press [PRESET EQ] to select a setting.
Every time you press the button:
HEAVY SOFT CLEAR
EQ-OFF
(cancelled)
DISCO LIVE HALL
HEAVY (sound quality) : Adds punch to rock
SOFT (sound quality) : For background music
CLEAR (sound quality): Clarifies higher sounds
DISCO (sound field) : Produces sound with the same kind of
lengthy reverberations heard at a disco
LIVE (sound field) : Makes vocals more alive
HALL (sound field) : Adds an expansiveness to the sound to
producetheatmosphere ofagreatconcert
hall
Note
You cannot use PRESET EQ and SUPER SOUND EQ together.
KARAOKE
Side A
Tab for side B Tab for side A
Using the built-in sound quality/sound
field settings
Enjoying karaoke
This system lets you enjoy KARAOKE with audio CDs and audio
tapes.
1First, lower volume with [MIC VOL], then connect the
microphone (not included).
Plug type: 3.5 mm monaural
2Press [SHIFT] + [KARAOKE] on the remote control to
select the voice mode.
Every time you press the button:
V.MUTE MONO L MONO R
(OFF)
Voice mode selection
If you want to play with the KARAOKE function, check first whether
or not your software is formatted for KARAOKE and then select
the voice mode as indicated below.
_: Appropriate
a: For practice, etc.
Note
A bar is indicated in the above table when the voice mode is least
effective. It is better to avoid using the mode in such cases.
V.MUTE function:
The voice portion of the track is blocked out but not the back-
ground music.
You need software recorded in stereo sound if you want to use
the voice mute function. Voice and/or static may be reproduced
with the following types of software.
•Software recorded monaural
•Classical music, or works performed by a limited number of
instruments
•Chorus works or duets
3Start the source (CD, etc.).
4Adjust volume with [VOLUME] and [MIC VOL] and sing
along.
To cancel the Karaoke
Press [SHIFT] + [KARAOKE] on the remote control to select “(OFF)”
mode.
Note
•If strange noise (squealing or howling) is emitted during use, move
the microphone further away from the speakers, or turn down the
microphone volume.
•When you are not using the microphone, disconnect it from the MIC
jack, and turn down the microphone volume level to MIN.
•Sound quality can be adjusted when using KARAOKE but recording
will not be affected.
(Continued on next page)
Soft-
ware
(OFF)
V.MUTE
MONO L
MONO R
a
(Background
music+Voice)
_
(Background
music)
–
––
a
(Voice)
–_
––
_
a
(For singing
along)
Sound
multiplex Stereo
Non-
KARAOKE
Voice
modes
KARAOKE
Recording
Adhesive tape
Enhancing the sound quality
You can enhance the bass and treble effect of the sound.
Press [SUPER SOUND EQ].
Remote control: Press [S.SOUND EQ].
The button light comes on.
Press the button again to cancel.
The button light goes out.
Adjusting the bass
Press [SUBWOOFER].
Remote control: Press [SHIFT] + [S.WOOFER].
The button light comes on.
Each time you press the button:
MID (medium) →MAX (high) →Light off (off)
To cancel
Press [SUBWOOFER] to turn the light off.
Remote control: Press [SHIFT] + [S.WOOFER].
Note
You cannot use this function when headphones are connected.
→

RQT7418
16
ENGLISH
Optional antenna connections
Use outdoor antenna if radio reception is poor.
FM outdoor antenna
•Disconnect the FM indoor antenna.
•The antenna should be installed by a competent technician.
AM outdoor antenna
Run a piece of vinyl wire horizontally across a window or other
convenient location.
Leave the loop antenna connected.
Note
Disconnect the outdoor antenna when the unit is not in use.
Do not use the outdoor antenna during an electrical storm.
External unit connections
•An analog player with a built-in phono equalizer can be connected.
•For details, refer to the instruction manual of the units which are to
be connected.
•When units other than those described above are to be connected,
please consult your audio dealer.
KARAOKE Other functions
AM outdoor antenna (not included)
AM loop
antenna
(included)
5 -12 m
1
2
Enjoying karaoke
To record your “KARAOKE”performance
Preparations:
•Do steps 1 and 2 on page 14: “Recording”.
•Do steps 1 and 2 on page 15: “Enjoying karaoke”.
•When singing along with CDs
Insert the desired discs (A page 8).
•When singing along with tape
Insert the desired tape into deck 1. (A page 14).
Press [a, REC] and start karaoke performance.
To stop recording
Press [L, STOP].
Note
•To playback the recorded tape, be sure to press [SHIFT] +
[KARAOKE] on the remote control to select the “(OFF)”mode.
•You cannot play or record KARAOKE with radio backing.
To record your voice
Preparation: Do steps 1 and 2 on page 14: “Recording”.
Ensure there is no tape in deck 1.
1. First, lower volume with [MIC VOL], then connect the microphone.
2. Press [a, REC] to start recording.
3. Speak through the microphone and adjust volume with [VOLUME]
and [MIC VOL].
Analog player
(not included)
Rear panel of
this unit
(L)
(R)
RL
FM outdoor antenna
(not included)
75 Ωcoaxial cable (not included)
1
30 mm
15 mm
1
2
3
2
Shield braid
Core wire
L, STOP
[, REC
AUX
Microphone
(not included)
MIC
MIC VOL
DISP, –DEMO
VOLUME
Headphones
(not included)
PHONES
DIMMER
CLOCK/TIMER
MUTING
KARAOKE
SHIFT
AUTO OFF
g , REW/3,
f , 4/FF

RQT7418
17
ENGLISH
Other functions
PL
: This is a 12-hour clock.
GCP : This is a 24-hour clock.
1Switch on the power.
2Press [SHIFT] + [CLOCK/TIMER] to select “CLOCK”.
Every time you press the button:
3(Within 7 seconds or so)
Press [g, REW/3] or [f, 4/FF] to set the time.
4Press [SHIFT] + [CLOCK/TIMER] to finish setting the
time.
The display will return to whatever was displayed before you set
the time.
To display the time
Press [SHIFT] + [CLOCK/TIMER] once when the unit is on or at
standby mode.
The time is shown for about 5 seconds.
Note
Reset the clock regularly to maintain accuracy.
Remote control only
When CD or tape is selected as the source
To save power, the unit turns off if it is left unused for ten minutes.
This function does not work if the source is tuner or AUX.
Press [SHIFT] + [AUTO OFF].
“AUTO OFF” is shown on the display.
The setting is maintained even if the unit is turned off.
If you select tuner or AUX as the source, “AUTO OFF” goes out. It
comes on again when you select CD or tape.
To cancel
Press [SHIFT] + [AUTO OFF] again.
Convenient functions
To dim the display panel
Remote control only
Press [DIMMER].
The display is dimmed and the indicators are turned off.
(The AC supply indicator remains on.)
Press [DIMMER] again to restore the display.
Auto-off function
Setting the time
Remote control only
Turning the demo function on/off
When the unit is first plugged in, a demonstration of its functions may
be shown on the display.
If the demo setting is off, you can show a demonstration by selecting
“DEMO ON”.
Press and hold [DISP, –DEMO].
The display changes each time the button is held down.
NO DEMO (off) ↔DEMO ON (on)
While in the standby mode, select “NO DEMO” to reduce power
consumption.
Note
DEMO function cannot be turned on when Dimmer is on.
Previous display
CLOCK RECPLAY
Using an external unit
(See page 16 for external unit connection.)
1. Press [AUX].
The unit comes on.
2. For listening: Proceed to step 3.
For recording: Press [a, REC] (recording starts).
3. Start playback from the external source. (For details, refer to the
external unit’s instruction manual.)
Using headphones (not included)
Reduce the volume level and connect the headphones.
Plug type: 3.5 mm stereo
Note
Avoid listening for prolonged periods of time to prevent hearing damage.
Switching displays
Press [DISP, –DEMO] to select the desired display mode.
Every time you press the button:
Normal
(OFF)
Peak hold Reflection
To mute the volume
Remote control only
Press [MUTING].
Press the button again to cancel.
“MUTING”goes out.
To cancel from the unit, turn [VOLUME] to minimum (--dB), then raise
it to the required level.
Muting is also cancelled when the unit is turned off.

RQT7418
18
ENGLISH
To check the settings
Press [SHIFT] + [CLOCK/TIMER] while the unit is on to select “rPLAY”
or “rREC”.
The settings are shown in the following order:
Play timer: start time→finish time→source→volume
Record timer: start time→finish time→source
To check the settings while the unit is off, press [SHIFT] + [CLOCK/
TIMER] twice.
If you use the unit after the timers are set
After using, check that the correct tape/CD are loaded before turning
the unit off.
Note
•If you turn the unit off and on again while a timer is functioning, the
finish time setting will not be activated.
•If you selected AUX as the source, when the timer comes on, the
unit turns on and engages “AUX”as the source. If you want to
playback or record from a connected unit, set that unit’s timer to the
same time. (See the connected unit’s instruction manual.)
Using the sleep timer
Remote control only
This timer turns the unit off after a set time.
While enjoying the desired source:
Press [SLEEP] to select the time (minutes).
Every time you press the button:
SLEEP 90 SLEEP 120SLEEP 60SLEEP 30 SLEEP OFF
To cancel the sleep timer
Press [SLEEP] to select “SLEEP OFF”.
To confirm the remaining time
Press [SLEEP] once.
The remaining time is shown for about 5 seconds.
To change the setting
Press [SLEEP] to select the new setting.
You can use the sleep timer in combination with the play/record timer.
Make sure the unit is off before the play/record timer’s start time.
Note
The sleep timer will be turned off when you start recording from a CD.
Using the play/record timer
Remote control only
You can set the timer to come on at a certain time to wake you up
(play timer) or to record a radio station or from the aux source (record
timer).
The play and record timers cannot be used together.
Preparations:
•Turn the unit on and set the clock (Apage 17).
•For the play timer, prepare the desired music source (tape/CD/
radio/aux), and set the volume.
•For the record timer, check the cassette’s erasure prevention tabs
(Apage 15) and insert the tape in deck 2 (Apage 14). Tune to
the radio station (Apage 13) or select the aux source (Apage
17).
1Press [SHIFT] + [CLOCK/TIMER] to select the timer
function.
Every time you press the button:
rPLAY: to set the play timer
rREC: to set the record timer
2ON time setting
1(Within 8 seconds or so)
Press [g, REW/3] or [f, 4/FF] to set the
start time.
2Press [SHIFT] + [CLOCK/TIMER].
3OFF time setting
1Press [g, REW/3] or [f, 4/FF] to set the
finish time.
2Press [SHIFT] + [CLOCK/TIMER].
The start and finish times are now set.
4Press [SHIFT] + [rPLAY/REC] to display the timer
indicator.
Every time you press the button:
RECPLAY
(off)
rPLAY: to turn the play timer on
rREC: to turn the record timer on
(The indicator doesn’t appear if the start and finish times or the
clock hasn’t been set.)
5Press [ff
ff
f] to turn the unit off.
The unit must be off for the timers to operate.
•Play timer: Play will start in the set condition at the set time
with volume increasing gradually to the set level.
•Record timer: The unit comes on 30 seconds before the set
time with the volume muted.
Timers
To cancel the timer
Press [SHIFT] + [rPLAY/REC] to clear the timer indicator from the
display.
(The timer comes on at the set time everyday if the timer is on.)
To change the settings (when the unit is on)
To change the play/record times
Do steps 1, 2, 3 and 5.
To change the source or volume
1. Press [SHIFT] + [rPLAY/REC] to clear the timer indicator from the
display.
2. Make changes to the source or volume.
3. Do steps 4 to 5.
To change the timer
Press [SHIFT] + [rPLAY/REC] to select the desired timer.
Every time the button is pressed:
RECPLAY
(off)
Previous display
CLOCK RECPLAY
rr
rr
rPLAY/REC
g , REW/3,
f , 4/FF
CLOCK/TIMER
ff
ff
f
SLEEP
SHIFT

RQT7418
19
ENGLISH
Troubleshooting guide
When there is a television set nearby
The picture on the TV
disappears or stripes
appear on the screen.
The location and orientation of the antenna are incorrect. If you are using an indoor antenna, change to
an outdoor antenna.
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from the unit.
Playing discs
The display is wrong or
play won’t start.
The total number of tracks
displayed differs each time
the same disc is inserted.
Unusual sound is heard.
CD-RW cannot be read.
“VBR–” is displayed
instead of the remaining
play time.
“TAKE OUT/DISC” appears
on the display.
The disc may be upside down. 8
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait for about an
hour for it to clear and try again.
The disc may be scratched, or its data may be defective. Replace the disc.
The disc was incompletely formatted. Use the recording equipment to fully format the disc before recording.
The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
There is a problem with the disc mechanism. (A power failure may have occurred.)
The tray will open automatically. Remove the disc from the tray, and after ensuring there is no disc in the tray,
close it. The unit will make the disc changing noises for a few moments and then it should operate normally.
Listening to the radio
Noise is heard.
The stereo indicator flickers
or doesn’t light.
Sound is distorted.
A beat sound is heard.
A low hum is heard during
AM broadcasts.
Use an outdoor antenna. ^
Turn the TV off or separate it from the unit.
Separate the antenna from other cables and cords.
Using the cassette deck
Poor quality sound.
Recording is not possible. Clean the heads. See below
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. %
Remote control
Remote control doesn’t
work. Check that the batteries are inserted correctly. 4
Replace the batteries if they are worn.
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
•Never use alcohol, paint thinner or benzene to clean this unit.
•Before using a chemically treated cloth, read the instructions that
came with the cloth carefully.
Maintenance
For a cleaner, crisper sound
Clean the heads regularly to assure good quality playback and
recording.
Use a cleaning tape (not included).
Common Problems
Although the unit is in
standby mode, the display
lights up and changes
continuously.
No sound.
Sound stops.
Sound is unfixed, reversed or
comes from one speaker
only.
Humming heard during play.
“ERROR” is displayed.
“– –:– –” appears on the
display at standby mode.
“F61” is displayed.
Turn off the demo function. &
If you set the clock, demo function will be turned off automatically. &
Turn the volume up.
Switch off the unit, determine and correct the cause, then switch the unit on. Causes include shorting of
the positive and negative speaker wires, straining of the speakers through excessive volume or power,
and using the unit in a hot environment.
Check the speaker connections. 6
An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away
from this unit’s cables.
Incorrect operation performed. Read the instructions and try again.
You plugged the AC power supply cord in for the first time or there was a power failure recently. Set the
time. &
Check and correct the speaker cords connection. 6
If this does not fix the problem, there is a power supply problem. Consult the dealer.
Before requesting service, make the checks below. If you can’t fix the system as described below, or if something not listed here occurs, refer to the
enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Reference pages are shown as black circled numbers &.

RQT7418
20
ENGLISH
Specifications
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
AMPLIFIER SECTION
PL
PMPO 3500 W
Power output
THD 10%, both channels driven
60 Hz–3 kHz
(Low channel) 55 W per channel (6 Ω)
3 kHz–16 kHz
(High channel) 55 W per channel (6 Ω)
40 Hz–100 Hz
(Subwoofer channel) 140 W (8 Ω)
Total power 360 W (Total)
Power output
THD 10%, both channels driven
1 kHz
(Low channel) 65 W per channel (6 Ω)
10 kHz
(High channel) 65 W per channel (6 Ω)
80 Hz
(Subwoofer channel) 160 W (8 Ω)
Total power 420 W (Total)
Input sensitivity
AUX 250 mV
MIC 0.7 mV
Input Impedance
AUX 13.3 kΩ
MIC 680 Ω
AMPLIFIER SECTION
GCP
RMS Power output
THD 10%, both channels driven
1 kHz
(Low channel) 65 W per channel (6 Ω)
10 kHz
(High channel) 65 W per channel (6 Ω)
80 Hz
(Subwoofer channel) 160 W (8 Ω)
Total power 420 W (Total)
Input sensitivity
AUX 250 mV
MIC 0.7 mV
Input Impedance
AUX 13.3 kΩ
MIC 680 Ω
CASSETTE DECK SECTION
Track system 4 track, 2 channel
Heads
Record/playback Solid permalloy head
Erasure Double gap ferrite head
Motor DC servo motor
Recording system AC bias 100 kHz
Erasing system AC erase 100 kHz
Tape speed 4.8 cm/s
Overall frequency response
(+3 dB, –6 dB at DECK OUT)
NORMAL (TYPE I) 35 Hz – 14 kHz
S/N 50 dB (A weighted)
Wow and flutter 0.18% (WRMS)
Fast forward and rewind time
Approx. 120 seconds with
C-60 cassette tape
CD SECTION
Sampling frequency 44.1 kHz
Decoding 16 bit linear
Beam source/wavelength
Semiconductor laser/780 nm
Number of channels Stereo
Frequency response
20 Hz–20 kHz (+1, –2 dB)
Wow and flutter Below measurable limit
Digital filter 8 fs
D/A converter MASH (1 bit DAC)
MP3
Bit rate 32 kbps–320 kbps
Sampling frequency
32 kHz, 44.1 kHz, 48 kHz
FM TUNER SECTION
PL
Frequency range
87.9 – 107.9 MHz (200 kHz steps)
87.5 – 108.0 MHz (100 kHz steps)
GCP
Frequency range
87.50 – 108.00 MHz (50 kHz steps)
Sensitivity 2.5 ØV (IHF)
S/N 26 dB 2.2 ØV
Antenna terminal(s) 75 Ω(unbalanced)
AM TUNER SECTION
PL
Frequency range
520 – 1710 kHz (10 kHz steps)
GCP
Frequency range
522 – 1629 kHz (9 kHz steps)
520 – 1630 kHz (10 kHz steps)
Sensitivity
PL
S/N 20 dB (at 1000 kHz) 560 ØV/m
GCP
S/N 20 dB (at 999 kHz) 560 ØV/m
SPEAKER SECTION
Front speakers SB-AK520
Type 3 way, 3 speaker system
Speaker(s)
Woofer 16 cm cone type
Tweeter 6 cm cone type
Super tweeter 2.5 cm piezo type
Impedance
HIGH 6 Ω
LOW 6 Ω
Input power (IEC)
HIGH 65 W (Max)
LOW 65 W (Max)
Output sound pressure level
83 dB/W (1.0 m)
Cross over frequency 2.6 kHz, 10 kHz
Frequency range 37 Hz–23 kHz (–16 dB)
44 Hz–22 kHz (–10 dB)
Dimensions (WxHxD) 241 x 360 x 239 mm
Mass 3.8 kg
Subwoofer SB-WAK520
Type 1 way, 1 speaker system
Speaker(s)
Subwoofer 16 cm cone type
Impedance 8 Ω
Input power (IEC) 160 W (Max)
Output sound pressure level
80 dB/W (1.0 m)
Frequency range 40 Hz–220 Hz (–16 dB)
45 Hz–180 Hz (–10 dB)
Dimensions (WxHxD) 266 x 331 x 264 mm
Mass 4.1 kg
GENERAL
Power supply
PL
AC 120 V, 60 Hz
GCP
AC 110/127/220–230/240 V, 50/60 Hz
Power consumption
PL
267 W
GCP
279 W
Dimensions (WxHxD) 250 x 330 x 369 mm
Mass
PL
8.2 kg
GCP
8.1 kg
Power consumption in standby mode
PL
0.34 W
GCP
0.85 W
Note
1. Specifications are subject to change
without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by
the digital spectrum analyzer.
3. The labels “HIGH” and “LOW” on the rear
of the speakers refer to High frequency
and Low frequency.