Panasonic KX-TVA50 Owner's manual

Document Version 3.0 2010/06
Programming Manual
Voice Processing System
Model No. KX-TVA50
KX-TVA200
Thank you for purchasing a Panasonic Voice Processing System.
Please read this manual carefully before using this product and save this manual for future use.
KX-TVA50/KX-TVA200: Version 3.0 (Main Software Version 3.00 or later)

Introduction
About this Manual
This Programming Manual is designed to serve as an overall reference for programming the Panasonic Voice
Processing System using KX-TVA Maintenance Console. It explains how to use KX-TVA Maintenance
Console, and obtain the most out of system administration.
This manual is divided into the following sections:
Section 1 Programming Instructions
Describes how to install, start, and operate KX-TVA Maintenance Console.
Section 2 KX-TVA Maintenance Console Operating Instructions
Describes in detail each parameter that can be programmed using KX-TVA Maintenance Console.
Index
An alphabetical listing of features and terms, as well as the page numbers of related sections.
About the Other Manuals
Installation Manual
The Voice Processing System Installation Manual provides instructions for installing the VPS hardware,
configuring the connected PBX for use with the VPS, and getting started with the KX-TVA Maintenance
Console software. Relevant sections from the Installation Manual are listed throughout this manual for your
reference.
Feature Manual
The Voice Processing System Feature Manual is an overall reference describing VPS features. It explains
what the VPS can do, and how to obtain the most of its many features. Sections from the Feature Manual are
listed throughout this manual for your reference.
Manager’s Manual
The Voice Processing System Manager’s Manual describes the programming and maintenance features
available to the System Manager and Message Manager. Relevant sections from the Manager’s Manual are
listed throughout this manual for your reference.
Subscriber’s Manual
The Voice Processing System Subscriber’s Manual describes how subscribers can access commonly used
VPS features and functions with their extensions and mailboxes. Relevant sections from the Subscriber’s
Manual are listed throughout this manual for your reference.
Glossary
The Voice Processing System Glossary is an alphabetical listing of features, terms, and abbreviations, as well
as their definitions.
Note
•This manual may refer to products not available in your country/area.
•For KX-TD500, KX-TDE series, KX-TDA series, and KX-TAW series PBXs, the term "trunk (CO line)" used
in this manual indicates a trunk (CO line) group.
2 Programming Manual Document Version 3.0 2010/06
Introduction

Trademarks
•Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
•Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the
United States and other countries.
•All other trademarks identified herein are the property of their respective owners.
•Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
Document Version 3.0 2010/06 Programming Manual 3
Introduction

Table of Contents
1 Programming Instructions ......................................................................7
1.1 Introduction to System Administration ...........................................................................8
1.2 KX-TVA Maintenance Console Installation .....................................................................9
1.3 Starting KX-TVA Maintenance Console ........................................................................11
1.4 File ....................................................................................................................................15
1.4.1 File—New .......................................................................................................................15
1.4.2 File—Open... ..................................................................................................................15
1.4.3 File—Close .....................................................................................................................15
1.4.4 File—Save ......................................................................................................................16
1.4.5 File—Save As... ..............................................................................................................16
1.4.6 File—Exit ........................................................................................................................16
1.5 Connect ............................................................................................................................17
1.5.1 Connect—Connection Profile .........................................................................................17
1.5.2 Connect—LAN (TCP/IP) (Optional for KX-TVA50) ........................................................17
1.5.3 Connect—USB ...............................................................................................................17
1.5.4 Connect—Dial-up (Modem) (Optional) ...........................................................................17
1.5.5 Connect—Disconnect .....................................................................................................18
1.6 Edit ...................................................................................................................................19
1.6.1 Edit—Undo .....................................................................................................................19
1.6.2 Edit—Cut ........................................................................................................................19
1.6.3 Edit—Copy .....................................................................................................................19
1.6.4 Edit—Paste ....................................................................................................................19
1.6.5 Edit—Select All ...............................................................................................................19
1.6.6 Edit—Delete ...................................................................................................................20
1.7 View ..................................................................................................................................21
1.7.1 View—Toolbar ................................................................................................................21
1.7.2 View—Status Bar ...........................................................................................................21
1.7.3 View—Shortcut Bar ........................................................................................................21
1.7.4 View—Utility Bar .............................................................................................................21
1.7.5 View—Menu Bar ............................................................................................................21
1.8 Go To ................................................................................................................................23
1.8.1 Go To—Mailbox Settings ...............................................................................................23
1.8.2 Go To—Class Of Service ...............................................................................................23
1.8.3 Go To—PORT/TRUNK Service .....................................................................................23
1.8.4 Go To—Service Settings ................................................................................................23
1.8.5 Go To—System Parameters ..........................................................................................23
1.8.6 Go To—H/W Settings .....................................................................................................24
1.8.7 Go To—Reports .............................................................................................................24
1.8.8 Go To—System Security ................................................................................................24
1.9 Utility ................................................................................................................................25
1.9.1 Utility—Quick Setup .......................................................................................................25
1.9.2 Utility—System Back Up ................................................................................................26
1.9.3 Utility—System Prompts Customization .........................................................................28
1.9.4 Utility—Port Status .........................................................................................................30
1.9.5 Utility—System Trace .....................................................................................................30
1.9.6 Utility—System Maintenance .........................................................................................31
1.9.7 Utility—System Initialize/Restart ....................................................................................32
1.9.8 Utility—Diagnostic ..........................................................................................................33
1.9.9 Utility—Programmer Code .............................................................................................33
1.9.10 Utility—Screen Customize ..............................................................................................33
1.9.11 Utility—Commands .........................................................................................................34
1.9.11.1 Changing the Mailbox No. Length Mode .....................................................................34
4 Programming Manual Document Version 3.0 2010/06
Table of Contents

1.9.11.2 Changing the Maximum Length of Mailbox Numbers ..................................................34
1.9.11.3 Two-way Recording Save Mode ..................................................................................35
1.9.12 Utility—Software Version ................................................................................................35
1.9.13 Utility—LAN Settings ......................................................................................................35
1.9.14 Utility—Default Parameters ............................................................................................38
1.9.15 Utility—Profile Setup ......................................................................................................38
2 KX-TVA Maintenance Console Operating Instructions ......................41
2.1 Mailbox Settings ..............................................................................................................42
2.1.1 Mailbox Settings Screen .................................................................................................42
2.1.2 Default Mailbox Template ...............................................................................................45
2.1.3 Mailbox Parameters .......................................................................................................46
2.1.4 Notification Parameters ..................................................................................................54
2.1.4.1 Notification Schedule ...................................................................................................56
2.1.4.2 Device Notification Timer .............................................................................................59
2.1.5 External Message Delivery .............................................................................................62
2.1.6 Auto Forwarding .............................................................................................................64
2.1.7 Personal Distribution List ................................................................................................66
2.1.7.1 List No. 1–List No. 4 ....................................................................................................66
2.1.8 Personal Custom Service ...............................................................................................68
2.1.9 Remote Call FWD To CO ...............................................................................................71
2.1.10 Automatic Login ..............................................................................................................73
2.1.11 E-mail Option ..................................................................................................................76
2.2 Class of Service ..............................................................................................................79
2.2.1 Class of Service .............................................................................................................80
2.2.2 Personal Options ............................................................................................................85
2.3 PORT/TRUNK Service .....................................................................................................92
2.3.1 Service Group ................................................................................................................92
2.3.1.1 Call Service .................................................................................................................94
2.4 Service Settings ..............................................................................................................97
2.4.1 Caller ID/DID/PIN Call Routing .......................................................................................97
2.4.1.1 Caller ID No./DID No./PIN No. ...................................................................................100
2.4.2 Holiday Settings ...........................................................................................................102
2.4.2.1 Holiday Service No. ...................................................................................................103
2.4.3 Parameters ...................................................................................................................107
2.4.3.1 Automated Attendant .................................................................................................107
2.4.3.2 Operator Service No. 1, 2, and 3 ...............................................................................109
2.4.3.3 Rotary Telephone Service .........................................................................................113
2.4.3.4 Name Entry ................................................................................................................114
2.4.3.5 Toll Saver ..................................................................................................................115
2.4.4 Custom Service ............................................................................................................117
2.4.4.1 Custom Service Builder .............................................................................................117
2.4.4.2 Menu & Transfer ........................................................................................................123
2.4.4.3 Date Control ..............................................................................................................127
2.4.4.4 Time Control ..............................................................................................................128
2.4.4.5 Day Control ................................................................................................................129
2.4.4.6 Password ...................................................................................................................130
2.5 System Parameters .......................................................................................................133
2.5.1 Mailbox Group ..............................................................................................................133
2.5.2 Extension Group ...........................................................................................................137
2.5.3 System Caller Name Announcement ...........................................................................140
2.5.4 Parameters ...................................................................................................................143
2.5.4.1 Time Setting ..............................................................................................................144
2.5.4.2 Prompt Setting ...........................................................................................................147
2.5.4.3 Language 1–5 (KX-TVA200), 1–3 (KX-TVA50) .........................................................148
Document Version 3.0 2010/06 Programming Manual 5
Table of Contents

2.5.4.4 System Guidance ......................................................................................................149
2.5.4.5 PBX Parameters ........................................................................................................151
2.5.4.6 Dialling Parameters ...................................................................................................161
2.5.4.7 Message Waiting Notification ....................................................................................163
2.5.4.8 External Message Delivery ........................................................................................166
2.5.4.9 Intercom Paging Parameters .....................................................................................169
2.5.4.10 Fax Management .......................................................................................................172
2.5.4.11 Disconnect Parameters .............................................................................................175
2.5.4.12 Transfer to Outside ....................................................................................................176
2.5.4.13 Long Distance Call ....................................................................................................182
2.5.4.14 VM Menu ...................................................................................................................183
2.5.4.15 E-mail Integration ......................................................................................................184
2.5.4.16 Advanced Settings .....................................................................................................186
2.6 Hardware (H/W) Settings ..............................................................................................189
2.7 Reports ...........................................................................................................................192
2.7.1 Mailbox Information Report ..........................................................................................193
2.7.2 Call Account Report .....................................................................................................196
2.7.3 Port Usage Report ........................................................................................................197
2.7.4 HDD Usage Report ......................................................................................................198
2.7.5 Mailbox Usage Report ..................................................................................................199
2.7.6 Fax Call Report ............................................................................................................200
2.7.7 Call Handling Statistics Report .....................................................................................201
2.7.8 Custom Service Report ................................................................................................202
2.7.9 Message Status Report ................................................................................................203
2.7.10 Subscriber Setup Report ..............................................................................................204
2.7.11 Security Information Report ..........................................................................................205
2.7.12 Hourly Statistics Report ................................................................................................206
2.7.13 E-mail Report ...............................................................................................................207
2.8 System Security ............................................................................................................208
2.8.1 Administrator ................................................................................................................208
2.8.2 Subscriber ....................................................................................................................211
2.8.2.1 Default Password ......................................................................................................212
Index............................................................................................................213
6 Programming Manual Document Version 3.0 2010/06
Table of Contents

Section 1
Programming Instructions
This section describes how to install, start, and operate
KX-TVA Maintenance Console.
Document Version 3.0 2010/06 Programming Manual 7

1.1 Introduction to System Administration
VPS programming can be performed by the System Administrator, System Manager, and Message Manager.
The type of programming performed by each is very different. While the System Manager and Message
Manager can use their telephones to program the PBX, the System Administrator must use KX-TVA
Maintenance Console and a PC.
VPS programming performed by the System Administrator is referred to as "system administration".
–System administration involves creating or changing VPS settings that control the manner in which VPS
performs, and is usually done before any other programming. (The system manager can program some
of these parameters with a telephone.)
–System administration can be performed by only one person at a time: a second person attempting to
program the VPS will be denied access to system administration.
8 Programming Manual Document Version 3.0 2010/06
1.1 Introduction to System Administration

1.2 KX-TVA Maintenance Console Installation
System programming, diagnosis, and data upload/download can be performed with a PC using the KX-TVA
Maintenance Console software.
System Requirements
Required Operating System
Microsoft® Windows® 2000, Windows XP Professional Service Pack 2, Windows Vista® Business Edition,
Windows 7 32-bit Professional Edition, or Windows 7 64-bit Professional Edition
Minimum Hardware Requirements for Windows 2000, Windows XP
CPU: 1.2 GHz Intel® Pentium® microprocessor
HDD: 150 MB of available hard disk space
RAM: 256 MB of available RAM
Minimum Hardware Requirements for Windows Vista
CPU: 1.8 GHz Intel Pentium microprocessor
HDD: 150 MB of available hard disk space
RAM: 1 GB of available RAM
Minimum Hardware Requirements for Windows 7 (32-bit)
CPU: 1.8 GHz or faster 32-bit (x86) processor
HDD: 150 MB of available hard disk space
RAM: 1 GB of available RAM
Minimum Hardware Requirements for Windows 7 (64-bit)
CPU: 1.8 GHz or faster 64-bit (x64) processor
HDD: 150 MB of available hard disk space
RAM: 2 GB of available RAM
Password Security
To maintain system security, a password is required to perform system programming. We recommend
changing the default password the first time you access the VPS via KX-TVA Maintenance Console. The default
password can be changed by running the Quick Setup utility (see 1.9.1 Utility—Quick Setup) or by selecting
System Security®Administrator®Password.
Warning to the Administrator regarding the system password
1. To avoid unauthorized access to VPS settings, which could result in fraudulent dialing, do not disclose the
password.
2. Please inform the customer of the importance of the password and the possible dangers if it becomes
known to others.
3. Please change the password periodically.
4. To prevent unauthorized access, we strongly recommend selecting a long and random password.
5. If the system password is forgotten, you have to reset the VPS to its factory defaults and reprogram it.
Note
•A Programmer Code, if set, is required to start KX-TVA Maintenance Console. You can set or delete
the Programmer Code by selecting Utility®Programmer Code. If no code is set, the KX-TVA
Maintenance Console can be started and used, but a password is required to connect to the VPS and
change VPS settings.
Document Version 3.0 2010/06 Programming Manual 9
1.2 KX-TVA Maintenance Console Installation

Installing KX-TVA Maintenance Console
1. Copy the KX-TVA Maintenance Console setup file to a local drive on the PC. (Its
icon is shown here, on the left.)
2. Double-click the setup file to run the installer.
3. Follow the on-screen instructions provided by the installation wizard.
4. Click Yes when prompted to copy the USB drivers, specify a location, then click
OK.
5. Click OK after the drivers have been copied to the local drive.
6. Click Finish.
Note
•To install or uninstall the software on a PC running Windows 2000 Professional or Windows XP
Professional, you must be logged in as a user that is in either the "Administrators" or "Power Users"
group.
•To install or uninstall the software on a PC running Windows Vista Business or Windows 7 Professional,
you must be logged in as a user in the "Administrators" group.
•When the VPS is first connected to the PC via USB, a wizard should appear and ask you to select the
appropriate USB driver. Browse for and select the KX-TVA USB driver, which is copied to the local
drive during installation.
10 Programming Manual Document Version 3.0 2010/06
1.2 KX-TVA Maintenance Console Installation

1.3 Starting KX-TVA Maintenance Console
The instructions listed below explain how to start KX-TVA Maintenance Console. These instructions are for
when connecting to the VPS via USB.
Note
•The screenshots shown here are for reference only, and may differ from the screens displayed on your
PC.
1. Click the KX-TVA Maintenance Console shortcut icon.
2. Select the appropriate VPS model and click OK.
3. The Enter Programmer Code dialog box is displayed. Enter the installer level programmer code (default:
INSTALLER) and click OK.
Note
•A programmer code is required to use the KX-TVA Maintenance Console. The System
Administrator can change the programmer codes (see 1.9.9 Utility—Programmer Code).
4. The Set Default Parameters window is displayed the first time you start KX-TVA Maintenance Console.
Select the TVA Type, PBX Type, and Integration Mode. Change the default parameters listed in the window
if necessary, then click OK.
Document Version 3.0 2010/06 Programming Manual 11
1.3 Starting KX-TVA Maintenance Console

5. The main window is displayed.
6. Click Connect ® USB from the menu bar, or click Connect on the toolbar, select USB in the Connection
Mode dialog box and click Next.
Note
•To connect to the VPS via USB, the KX-TVA USB driver must be installed on the PC, as explained
in 1.2 KX-TVA Maintenance Console Installation.
7. Enter the installer level password (default: 1234), then click Next.
Note
•The installer level password (also called the administrator password) is required to access the VPS
for programming. The System Administrator can change the password (see "Password" in
2.8.1 Administrator).
8. Click Finish when the message Connected! is displayed.
12 Programming Manual Document Version 3.0 2010/06
1.3 Starting KX-TVA Maintenance Console

9. You may now begin programming the VPS. To choose the area you would like to begin programming, click
the desired icon in the Shortcuts menu.
Note
•To connect to the VPS via LAN, first connect to the VPS via USB and set the appropriate LAN settings
(see 1.9.13 Utility—LAN Settings).
•To connect to the VPS via modem, see 1.5.4 Connect—Dial-up (Modem) (Optional).
•If programming the VPS for the first time, the Quick Setup utility can help you program essential settings
quickly and easily. See 1.9.1 Utility—Quick Setup for more information.
•KX-TVA Maintenance Console supports versions 1.0 and 1.1 of the KX-TVA50 and KX-TVA200. The
software performs according to the version number of the connected VPS.
•Software features, design, and system requirements are subject to change.
•When connecting the KX-TVA50 with a PC running Windows 7 via USB, if the PC enters Sleep or
Hybrid Sleep, the KX-TVA Maintenance Console may not be able to connect to the KX-TVA50 after it
wakes from Sleep or Hybrid Sleep. If this occurs, exit the KX-TVA Maintenance Console, and then
disconnect and reconnect the USB cable.
Programmer Levels and Passwords
There are two levels of access to the KX-TVA Maintenance Console: Installer and User. Each level has a
programmer code, which is required to start KX-TVA Maintenance Console, and a password, which is required
to access the VPS using KX-TVA Maintenance Console.
The Installer level provides access to all VPS programming parameters and should only be used by the System
Administrator.
Level Default
Programmer Code Default Password Restrictions
Installer INSTALLER*1 1234*2 No restrictions
User USER*1 1234*3 Access to screens and parameters can be
restricted*3
*1 See 1.9.9 Utility—Programmer Code to change the programmer codes.
*2 See 2.8.1 Administrator to change the Installer level password.
*3 See 1.9.10 Utility—Screen Customize to change the User level password and restrict User level access.
Document Version 3.0 2010/06 Programming Manual 13
1.3 Starting KX-TVA Maintenance Console

Program Mode
KX-TVA Maintenance Console has three programming modes: Initial, Batch, and Interactive. The current mode
is displayed in the lower-left corner of the screen.
Initial Mode
When KX-TVA Maintenance Console is started, it enters Initial mode. From here, you can choose to enter
Batch mode or Interactive mode to program the VPS.
Batch Mode
Batch mode allows you to create new system data files and make modifications to system data files saved on
your PC without being connected to the VPS. Later, when you connect to the VPS, the system data stored in
the PC can be uploaded to the VPS.
To enter Batch mode, select an option from the File menu (see 1.4 File).
Interactive Mode
Interactive mode allows you to directly modify the system data and settings saved in the VPS’s memory from
a PC that is connected to the VPS. This mode displays the system data that is currently being used by the
VPS. Data can be modified and results displayed in real time.
To enter Interactive mode, select an option from the Connect menu (see 1.5 Connect).
Standard Buttons
There are several standard buttons that are displayed on many screens within KX-TVA Maintenance
Console.
Button Function
OK Accepts the settings that were made in the current screen and closes the screen.
Apply Accepts the settings that were made in the current screen and leaves the screen
open.
Cancel Ignores any changes made in the current screen and returns to the previous
screen.
Help Displays the relevant help topic for the current screen.
14 Programming Manual Document Version 3.0 2010/06
1.3 Starting KX-TVA Maintenance Console

1.4 File
The File menu allows you to create, open or save a data file. If "New" or "Open..." are selected, KX-TVA
Maintenance Console automatically enters Batch mode.
1.4.1 File—New
Creates a new system data file, and puts KX-TVA Maintenance Console in Batch mode. All settings are in their
initial or default state. To upload the file created here to the VPS, see 1.9.2 Utility—System Back Up.
Note
•Since selecting this option creates a new system data file, uploading this new file to the VPS as is will
overwrite any settings that are saved in the VPS’s memory. Use with care.
To create a new system data file
From the File menu, select New.
1.4.2 File—Open...
Opens a system data file saved on the PC, and puts KX-TVA Maintenance Console in Batch mode.
When opening a file created with an older version of KX-TVA Maintenance Console (such as version 1.0), you
will be asked whether you want to convert the data for use with the current version or not.
Using the data without converting may result in certain data being loaded to an incorrect destination, and is
not recommended.
System data files for unsupported VPS models cannot be opened. Only files saved with KX-TVA Maintenance
Console can be opened.
To upload the file modified here to the VPS, see 1.9.2 Utility—System Back Up.
To open a system data file
1. From the File menu, select Open....
The Open dialog box will be displayed.
2. Navigate to the folder containing the system data file you want to open.
3. Select the file.
4. Click Open.
If the file was created with an older version of KX-TVA Maintenance Console, you will be asked if you want
to convert the data.
a. Click Convert to convert the data for use with the current version of KX-TVA Maintenance Console.
Enter a name for the new converted system data file.
b. Click Start Version 1.x to open the file without converting it (not recommended).
1.4.3 File—Close
Closes currently opened system data files, and enters Initial mode. This menu is only available when using
the KX-TVA Maintenance Console in Batch mode.
Document Version 3.0 2010/06 Programming Manual 15
1.4.3 File—Close

To enter Initial mode
•From the File menu, select Close.
If the system data file being modified has not been saved, a warning message will be displayed, giving you
the option to save the file.
a. Click Yes to save the file and close system data files to enter Initial mode.
b. Click No to discard the changes and close system data files to enter Initial mode.
1.4.4 File—Save
Overwrites the previously saved system data file with the system data currently being modified.
To upload a file to the VPS that was saved here, see 1.9.2 Utility—System Back Up.
To save a system data file
From the File menu, select Save.
If the data has never been saved, the Save dialog box will be displayed. For more details, see 1.4.5 File—
Save As....
1.4.5 File—Save As...
Saves the system data file being modified with the name chosen by the user.
To upload a file saved here to the VPS, see 1.9.2 Utility—System Back Up.
To save a system data file with a new name
1. From the File menu, select Save As....
2. Navigate to the folder in which you want to save the file.
3. Enter a file name, or select a file to overwrite.
4. Click Save.
If choosing to overwrite another file, a warning message will be displayed.
a. Click Yes to overwrite.
b. Click No to return to the previous screen.
1.4.6 File—Exit
Closes KX-TVA Maintenance Console.
To exit KX-TVA Maintenance Console
From the File menu, select Exit.
If the system data file being modified has not been saved, a warning message will be displayed, giving you
the option to save the file.
a. Click Yes to save the file and exit KX-TVA Maintenance Console.
b. Click No to discard the changes and exit KX-TVA Maintenance Console.
16 Programming Manual Document Version 3.0 2010/06
1.4.6 File—Exit

1.5 Connect
The Connect menu allows you to directly program the VPS in Interactive mode. When connecting, you are
required to enter the administrator password that corresponds to the programmer code you entered when
starting KX-TVA Maintenance Console.
1.5.1 Connect—Connection Profile
If you have saved a Connection Profile (see 1.9.15 Utility—Profile Setup), you can connect to the VPS using
the settings saved in the profile.
To connect using a Connection Profile
1. From the Connect menu, select Connection Profile.
2. Select the desired profile from the pull-down menu.
3. Enter the password required to connect to the VPS if it was not stored in the Connection Profile.
4. Click Next.
1.5.2 Connect—LAN (TCP/IP) (Optional for KX-TVA50)
Connects to the VPS through the LAN port of the VPS.
Note
•Before you connect to the VPS via LAN, you must first assign an IP address to the VPS. See
1.9.13 Utility—LAN Settings to assign an IP address.
To connect using a LAN
1. From the Connect menu, select LAN (TCP/IP).
2. Enter the IP address, port number, and password used to connect to the VPS.
3. Click Next, and Finish when the connection is completed.
1.5.3 Connect—USB
Connects to the VPS through the USB port on the VPS.
To connect using USB
1. From the Connect menu, select USB.
2. Enter the password used to connect to the VPS.
3. Click Next, and Finish when the connection is completed.
1.5.4 Connect—Dial-up (Modem) (Optional)
Connects to the VPS through the optional modem.
Document Version 3.0 2010/06 Programming Manual 17
1.5.4 Connect—Dial-up (Modem) (Optional)

Note
•To access the VPS remotely using this feature, a KX-TVA296 Modem Card must be installed. For more
details, see "2.7.5 Modem Card (KX-TVA296)" in the Installation Manual.
The following settings must be entered to match the settings of the modem and/or PC.
Setting Values Description
Phone No. – Enter the telephone number to dial into the VPS.
Port No. – Enter the port number used to connect to the VPS.
Password – Enter the password used to connect to the VPS.
To connect using a modem
1. From the Connect menu, select Dial-up (Modem).
2. Enter the administrator password and the settings as required.
3. Click Next, and Finish when the connection is completed.
1.5.5 Connect—Disconnect
Closes the connection between KX-TVA Maintenance Console and the VPS.
To disconnect
1. From the Connect menu, select Disconnect.
2. Click Yes.
18 Programming Manual Document Version 3.0 2010/06
1.5.5 Connect—Disconnect

1.6 Edit
The Edit menu allows you to easily edit data in KX-TVA Maintenance Console.
1.6.1 Edit—Undo
Returns the last changed setting to its previous value.
To undo
From the Edit menu, select Undo.
1.6.2 Edit—Cut
Cuts the selection and places it in the clipboard.
To cut
1. Select an area of text.
2. From the Edit menu, select Cut.
1.6.3 Edit—Copy
Copies the selection and places it in the clipboard.
To copy
1. Select an area of text.
2. From the Edit menu, select Copy.
1.6.4 Edit—Paste
Inserts the contents of the clipboard.
To paste
1. Place the cursor in the desired location.
2. From the Edit menu, select Paste.
1.6.5 Edit—Select All
Selects the entire document.
To select all
From the Edit menu, select Select All.
Document Version 3.0 2010/06 Programming Manual 19
1.6.5 Edit—Select All

1.6.6 Edit—Delete
Deletes selected items.
To delete
1. Select an item to be highlighted.
2. From the Edit menu, select Delete.
20 Programming Manual Document Version 3.0 2010/06
1.6.6 Edit—Delete