Panasonic CT-27HL15N User manual

MTNC050426A1
B19 Canada:B05
Color Television
CT-27HL15N
CT-27HL15UN
GN1M
Please file and use this manual together with Simplified manual for model CT-32HL15N , Order No. MTNC050309A1 and the main
service manual for Model CT-32HL44J, Order No. MTNC040418C1. A complete parts list and schematics difference from Order No.
MTNC050309A1 are included in this simplified service manual.
© 2005 Panasonic Corporation of North America. All rights reserved. Unauthorized copying and distribution is a violation of law.
Page
1
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

1 Safety precautions
General guidelines
An isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC power line.
Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical
shocks. It will also protect the receiver from being damaged by accidental shorting that may occur during servicing.
When servicing, observe the original lead dress, especially in the high voltage circuit. Replace all damaged parts (also parts that show
signs of overheating.)
Always replace protective devices, such as fish paper, isolation resistors and capacitors, and shields after servicing the receiver. Use
only manufacturer’s recommended rating for fuses, circuits breakers, etc.
High potentials are present when this receiver is operating. Operation of the receiver without the rear cover introduces danger for
electrical shock. Servicing should not be performed by anyone who is not thoroughly familiar with the necessary precautions when
servicing high voltage equipment.
Extreme care should be practiced when handling the picture tube. Rough handling may cause it to implode due to atmospheric
pressure. (14.7 lbs per sq. in.). Do not nick or scratch the glass or subject it to any undue pressure. When handling, use safety goggles
and heavy gloves for protection. Discharge the picture tube by shorting the anode to chassis ground (not to the cabinet or to other
mounting hardware). When discharging connect cold ground (i.e. dag ground lead) to the anode with a well insulated wire or use a
grounding probe.Avoid prolonged exposure at close range to unshielded areas of the picture tube to prevent exposure to x ray
radiation.
The test picture tube used for servicing the chassis at the bench should incorporate safety glass and magnetic shielding. The safety
glass provide shielding for the tube viewing area against x ray radiation as well as implosion. The magnetic shield limits the x ray
radiation around the bell of the picture tube in addition to the restricting magnetic effects. When using a picture tube test jig for service,
ensure that the jig is capable of handling 50kV without causing x ray radiation.
Before returning a serviced receiver to the owner, the service technician must thoroughly test the unit to ensure that is completely safe
to operate. Do not use a line isolation transformer when testing.
Leakage current cold check
Unplug the A.C. cord and connect a jumper between the two plug prongs.Measure the resistance between the jumpered AC plug and
expose metallic parts such as screwheads, antenna terminals, control shafts, etc. If the exposed metallic part has a return path to the
chassis, the reading should be between 240kΩand 5.2MΩ. If the exposed metallic part does not have a return path to the chassis, the
reading should be infinite.
Leakage current hot check
Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during the check.
Connect a 1.5kΩ10 watt resistor in parallel with a 0.15µF capacitor between an exposed metallic part and ground. Use earth ground,
for example a water pipe.
Using a DVM with a 1000 ohms/volt sensitivity or higher, measure the AC potential across the resistor.
Repeat the procedure and measure the voltage present with all other exposed metallic parts.
Verify that any potential does not exceed 0.75 volt RMS. A leakage current tester (such a Simpson model 229, Sencore model PR57
or equivalent) may be used in the above procedure, in which case any current measure must not exceed 0.5 milliamp. If any
measurement is out of the specified limits, there is a possibility of a shock hazard and the receiver must be repaired and rechecked
before it is returned to the customer.
Hot check circuit
Insulation test
Connect an insulation tester between an exposed metallic part and A.C. line. Apply 2500VAC/60Hz for 1 second. Confirm that the
current measurement is lower than 4.0mA. Repeat test with other metallic exposed parts.
X ray radiation
Page
2
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

WARNING
The potential source of x ray radiation in the TV set is in the high voltage section and the picture tube.
NOTE
It is important to use an accurate, calibrated high voltage meter.
Set the brightness, picture, sharpness and color controls to minimum.
Measure the high voltage. With a 480i or 1080i signal the high voltage should be 29.5kV ± 0.3kV. If the upper limit is out of tolerance,
immediate service and correction is required to insure safe operation and to prevent the possibility of premature component failure.
Horizontal oscillator disable circuit test
This test must be performed as a final check before the receiver is returned to the customer. See horizontal oscillator disable circuit
procedure check in this manual.‘
2 Service notes
NOTE
These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs
when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.
Leadless chip component (surface mount)
Chip components must be replaced with identical chips due to critical foil track spacing. There are no holes in the board to mount
standard transistors or diodes. Some chips capacitor or resistor board solder pads may have holes through the board, however the
hole diameter limits standard resistor replacement to 1/8 watt. Standard capacitor may also be limited for the same reason. It is
recommended that identical components be used.
Chip resistor have a three digit numerical resistance code, 1st and 2nd significant digits and a multiplier. Example: 162 = 1600 or
1.6kΩresistor, 0 = 0Ω(jumper).
Chip capacitors generally do not have the value indicated on the capacitor. The color of the component indicates the general range of
the capacitance.
Chip transistors are identified by a two letter code. The first letter indicates the type and the second letter, the grade of transistor.
Chip diodes have a two letter identification code as per the code chart and are a dual diode pack with either common anode or
common cathode. Check the parts list for correct diode number.
Component removal
1. Use solder wick to remove solder from component end caps or terminal.
2. Without pulling up, carefully twist the component with tweezers to break the adhesive.
3. Do not reuse removed leadless or chip components since they are subject to stress fracture during removal.
Chip component installation
1. Put a small amount of solder on the board soldering pads.
2. Hold the chip component against the soldering pads with tweezers or with a miniature alligator clip and apply heat to the pad area
with a 30 watt iron until solder flows. Do not apply heat for more than 3 seconds.
How to replace flat ic (required tools)
1. Remove the solder from all of the pins of a Flat IC by using a desolder braid
Page
3
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

2. Put the iron wire under the pins of the Flat IC and pull it in the direction indicated while heating the pins using a soldering iron. A
small awl can be used instead of the iron wire.
3. Remove the solder from all the pads of the Flat IC by using a de solder braid
4. Position the new Flat IC in place (apply the pins of the Flat IC to the soldering pads where the pins need to be soldered). Properly
determine the positions of the soldering pads and pins by correctly aligning the polarity symbol
5. Solder all pins to the soldering pads using a fine tipped soldering iron
6. Check with a magnifier for solder bridge between the pins or for dry joint between pins and soldering pads. To remove a solder
bridge, use a de solder braid as shown in the figure below
IMPORTANT
To protect against possible damage to the solid state devices due to arching or static discharge, make certain that all ground wires and
CRT DAG wire are securely connected.
CAUTION
The power supply circuit is above earth ground and the chassis cannot be polarized. Use an isolation transformer when servicing the
receiver to avoid damage to the test equipment or to the chassis. Connect the test equipment to the proper ground (hot) or (cold) when
servicing, or incorrect voltages will be measured.
WARNING
This receiver has been designed to meet or exceed applicable safety and x-ray radiation protection as specified by government
agencies and independent testing laboratories.
To maintain original product safety design standards relative to x-ray radiation and shock and fire hazard, parts indicated with the
symbol on the schematic must be replaced with identical parts. Order parts from the manufacturer’s parts center using the parts
numbers shown in this service manual, or provide the chassis number and the part reference number.
For optimum performance and reliability, all other parts should be replaced with components of identical specification.
Page
4
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

HORIZONTAL OSCILLATOR DISABLE CIRCUIT
This chassis employs a special circuit to protect against excessive high voltage and beam current. If, for any reason, the high voltage
and beam current exceed a predetermined level this protective circuit activates and detunes the horizontal oscillator that limits the high
voltage. The over-voltage protection circuit is not adjustable. However, if components indicated by the symbol on the schematic in
either the horizontal sweep system or the over-voltage protection circuit itself are changed, the operation of the circuit should be
checked using the following procedure:
Equipment needed to check the disabled circuit:
1. High voltage meter (0 ~ 50kV)
2. Variac or isolation transformer
3. D.C. current meter
4. Digital voltmeter
PREPARATION
1. Connect receiver to A.C. 120 Volts. Do not turn ON.
2. Connect HIGH VOLTAGE meter to 2nd anode (H.V. button).
NOTE
Use cold ground for negative lead.
3. Connect the ammeter serial from the flyback anode lead to the picture tube anode socket.
PROCEDURE
1. Apply a monoscope or white pattern.
2. Confirm that beam current is 2.0mA.
3. Adjust VR524 so that high voltage is 29.5kV ± 0.3kV.
4. Adjust VR538 so that digital meter reads 2.3 ± 0.05V
5. Confirm that high voltage protector (SOS) operates at 34.0kV or less by adjusting VR524.
6. Turn VR524 counter clockwise, turn tv on and apply a monoscope or white pattern.
7. Adjust VR524 so that high voltage meter reads 29.5 ± 0.3kV.
8. Once the adjustment is completed, apply a bond on VR524 and VR538. Confirm B+ 142V ± 6.0V with 120V A.C. applied.
NOTE
If high voltage is not within the specified limit the cause must be determined before the receiver is returned to the owner.
3 Receiver feature table
FEATURE/MODEL CT-27HL15N/UN
CHASSIS DP435
MICRO 256K
MENU LANGUAGE ENG/SPAN/FR
CLOSE CAPTION X
V-CHIP (USA/CANADA) X
VIDEO INPUT SKIP X
CHANNEL COUNT 181
REMOTE CONTROL (W/LIGHT) EUR7613ZC0
CRT SUPPLIER SAMSUNG
FAMILY GN1M
COMB FILTER 3D-Y/C
HEC/VEC (X=BOTH) X
VM
X (SELECTABLE)
V/A NORM (X=BOTH) X
COLOR TEMP X
AI PICTURE X
PRESET/INPUT LABELING X
VIDEO PICTURE MEMORY X
HDTV MONITOR 1080i
PROGRESSIVE SCAN DOUBLER X
EDTV MONITOR 480p
STEREO/SAP WITH dbx NR X
Page
5
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

Note:
Specifications are subject to change without notice or obligation. Dimensions and weights are approximate.
4 Board description table
NOTE
When ordering a replacement board assembly, append an “S” to the board number.
EXAMPLE
To order the A Board, the replacement board is TNP2AH071ACS.
NOTE:
The DG-Board is non-serviceable. If this board is defective, replace it with a new board.
5 TV Location of controls
5.1 CT-27HL15N/UN
STEREO WATTS PER CHANNEL 10W
No. OF SPEAKERS 2
BASS/BALANCE/TREBLE CONTROL
X
AI SOUND X
SURROUND X
SPATIALIZER/BBE BBE
A/V IN (REAR/FRONT) 4(3/1)
PROGRAM OUT X
AUDIO OUT (FAO / VAO) BOTH
COMPONENT INPUT (Y, Pb, Pr) 2
S-VIDEO INPUT (REAR/FRONT) 2/1
DIGITAL INTERFACE HDMI
WEIGHT (KG/LB)
43.0 KG/ 94.8LBS
DIMENSIONS (W/D/H) mm / in 780x508x572
BOARD CT-
27HL15N/UN
DESCRIPTION
A-BOARD TNP2AH071AC MAIN CHASSIS
D-BOARD TNP2AH073AF
HIGH VOLTAGE AND DEFLECTION
DG-
BOARD
TNP2AA216 DIGITAL VIDEO
G-BOARD TNP2AA222 FRONT A/V
H-BOARD TNP2AA174AB REAR A/V
L-BOARD TNP2AA232AC CRT BOARD
Page
6
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

6 Back cover removal
CT-27HL15N/UN
7 Chassis service adjustment
Page
7
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

procedures
All service adjustments are factory preset and should not require change unless controls and/or associated components are replaced.
140.0_V B+ voltage check
1. Set the BRIGHT and PICTURE to minimum by using the PICTURE menu.
2. Connect the DVM on TPD50 (D-Board by and cold ground
3. Confirm that B+ voltage is 142V ± 6.0V. This voltage supplies B+ to the horizontal output and flyback circuits.
Source voltage chart
120V AC line input. Set the BRIGHT and the PICTURE to minimum by using the PICTURE menu. Use cold or hot ground for the (-) lead
of the DVM as needed
High voltage check
A-BOARD VOLTAGE
STBY 7V (BY IC006) A-Board TPA9 7.5V ±
0.75V
MAIN 9V (BY IC006) A-Board TPA90 9.0V ± 0.5V
MAIN 5V (BY IC2856) A-Board TPA15 5.2V ± 0.3V
GC 2.5V (BY IC2856) A-Board TPA25 2.6V ± 0.2V
STBY 3.3V (BY A13 CONNECTOR) A-
Board TPA16
3.3V ± 0.2V
MAIN 3.3V (BY IC 2856) A-Board TPA33 3.3V ± 0.2V
D-BOARD VOLTAGE
+B2 (BY D14 CONNECTOR) D-Board TPD50 142.0 ± 6.0V
30V (BY IC805) D-Board TPD19 33.5 ± 2.0V
15V (BY IC802) D-Board TPD7 14.5 + 1.5V -1.0
-15V (BY IC805) D-Board TPD6 -15.5V ± 1.5V
SOUND+ (BY D6 CONNECTOR) D-Board TPD4 17.2V + 1.5V -
1.0
SOUND- (BY D6 CONNECTOR) D-Board TPD53 -18.0V ± 1.5V
210V (BY IC503) D-Board TPD34 211.0V ± 4.0V
MAIN 12V (BY D14 CONNECTOR) D-
Board TPD22
12V ± 0.5V
Page
8
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

1. Select an active TV channel and confirm that horizontal is in sync.
2. Adjust BRIGHTNESS and PICTURE using PICTURE icon menu so video just disappears.
3. Confirm B+ 142 ± 6.0V is within limit.
4. Using a high voltage meter confirm that the high voltage is 29.5kV ± 0.3kV.
7.1 Service adjustment default values for service items
NOTE:
The above table shows the default values for the service items, this values may vary depending on the serviced TV.
Important Note:
When changing “ID” register, message “Unplug AC to activate” will appear on the screen and the set must be unplugged.
REGISTER
DESCRIPTION FORMAT
4:3 16:9
MTSIN INPUT LEVEL 22 N/A
SEPAL LOW LEVEL SEPARATION 07 N/A
SEPAH HIGH LEVEL SEPARATION 22 N/A
CLOCK CLOCK 131 N/A
COLOR COLOR 1F N/A
TINT TINT 7D N/A
BRIGH SUB-BRIGHTNESS
09 53
N/A
CONT SUB-CONTRAST
02 A0
N/A
B-Y_G MAGENTA TINT ADJ 3D N/A
CUT G GREEN CUT-OFF
01 15
N/A
CUT R RED CUT-OFF
01 1A
N/A
CUT B BLUE CUT-OFF
01 17
N/A
BRT BRIGHT
09 53
N/A
R DR RED DRIVE 90 N/A
B DR BLUE DRIVE 95 N/A
R-Y_A R-Y_A 80 N/A
HLIN HORIZONTAL LINEARITY 80 N/A
HPOS HORIZONTAL POSITIONING
03 42
N/A
HWID HORIZONTAL WIDTH 95 N/A
PCC PINCUSHION CORRECTION D3 BD
PCCHG PINCUSHION HIGH 38 43
PCCLG PINCUSHION LOW 39 3F
PCCHS PINCUSHION HIGH 05 05
PCCLS PINCUSHION LOW 05 05
TOPG TOP CORNER PINCUSHION 58 58
BTMG BOTTOM CORNER PINCUSHION 58 58
TOPSL TOP CORNER PINCUSHION SLICE LEVEL 03 03
BTMSL
BOTTOM CORNER PINCUSHION SLICE LEVEL
03 03
TRAP TRAPEZOID 80 80
PARA PARALLELOGRAM 10 10
SIDE E-W PINCUSHION ADJUSTMENT 16 16
HTRAP HORIZONTAL TRAPEZOID 20 20
VRAS VERTICAL POSITION CA D6
VEAMP VERTICAL SIZE
01 0F
00 56
V-C VERTICAL LINEARITY 70 72
V-S VERTICAL S CORRECTION 56 58
HDAFS HORIZONTAL DAF PHASE
00 A4
N/A
VTOP VTOP
00 C4
00 B0
BDAC BDAC 73 N/A
INPIN INPIN 20 20
MOIRE MOIRE 80 80
ID ID 32 32
Page
9
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

8 Identification of components
8.1 TV with back cover removed
TV View with back cover removed.
8.2 G Board
G-Board View
9 Reference of PDF links color
10 Conductors View
Page
10
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

10.1 G-Board Printed Circuit
11 Schematic Diagrams
11.1 Schematic notes in english
Page
11
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

11.2 Schematic notes in spanish
11.3 A-Board Schematic 1 of 3
11.4 A-Board Schematic 2 of 3
Page
12
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

11.5 A-Board Schematic 3 of 3
11.6 D-Board Schematic 1 of 4
11.7 D-Board Schematic 2 of 4
11.8 D-Board Schematic 3 of 4
11.9 D-Board Schematic 4 of 4
11.10 G-Board Schematic
11.11 L-Board Schematic
12 Location Parts
CT-27HL15N/UN
Page
13
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

13 Parts list
13.1 Description of abbreviations guide
13.2 Parts list
Page
14
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

Ref. No. Part No. Part Name & Description
Remarks
CAPACITORS
C037 ECA0JM222B CAP E 2200UF-6.3V
C038 ECJ2VF1H103Z CAP C .01UF-Z-50V
C047 ECA1HM330B CAP E 33UF-50V
C054 ECA1HM4R7B CAP E 4.7UF-50V
C055 ECA1HM330B CAP E 33UF-50V
C056 ECA1VM471B CAP E 470UF-35V
C059 ECJ2VC1H101J CAP C 100PF-J-50V
C060 ECJ2VC1H101J CAP C 100PF-J-50V
C061 ECA1HMR22B CAP E .22UF-50V
C062 ECA1HM2R2B CAP E 2.2UF-50V
C096 ECJ2VC1H120J CAP C 12PF-J-50V
C097 ECJ2VC1H390J CAP C 39PF-J-50V
C451 ECA1EM102E CAP E 1000UF-25V
C452 ECA1EM102E CAP E 1000UF-25V
C453 ECA1HM101B CAP E 100UF-50V
C454 ECQV1H224JL3 CAP P .22UF-J-50V
C455 ECA1CM221B CAP E 10UF-16V
C457 ECQB1H471JF3 CAP P 470PF-J-50V
C458 ECQV1H105JL3 CAP P 1.0UF-J-50V
C460 ECQE2224KF3 CAP P .22UF-K-200V
C461 ECA1HM010B CAP E 1UF-50V
C462 ECA0JM221B CAP E 220UF-6.3V
C463 ECA1VM470B CAP E 47UF-35V
C467 ECQV1H224JL3 CAP P .22UF-J-50V
C472 ECA1HM4R7B CAP E 4.7UF-50V
C507
ECEA2CNR47SB
CAP E .47UF-160V
C508 ECQB1H104JF3 CAP P .10UF-J-50V
C509 ECKR3A222KBP CAP C .0022UF-K-1KV
C510 ECWH20332JVY CAP P 3300PF-J-2KV
C511 ECWH20472JVB CAP P 4700PF-J-2KV
C512 ECA1HMR47B CAP E .47UF-50V
C514 ECQM4472JZW CAP P 4700PF-J-400V
C515 ECKR3A222KBP CAP C .0022UF-K-1KV
C516 ECQB1H223JF3 CAP P .022UF-J-50V
C517 ECJ2VG1H151J CAP C 150-J-50V
C518
ECKW3D681KBR
CAP C 680PF-K-2KV
C519
ECKW3D681KBP
CAP C 680PF-K-2KV
C520
ECKW3D222KBP
CAP C 2200UF-K-2KV
C521 ECWF2334JSR CAP M .33UF-J-200V
C522 ECWF4393RJB CAP P .039UF-J-400V
C523 ECQB1H104JF3 CAP P .10UF-J-50V
C524 ECQE1224KF3 CAP P .22UF-K-100V
C525 EEUNA1E220B CAP E 22UF-25V
C526 ECQB1H104JF3 CAP P .10UF-J-50V
C527 ECQV1H224JL3 CAP P .22UF-J-50V
C529 ECQB1H473JF3 CAP P .047UF-J-50V
C532 ECQB1H104JF3 CAP P .10UF-J-50V
C534 ECQB1H103JF3 CAP P .01UF-J-50V
C535 ECQV1H104JL3 CAP P .10UF-J-50V
C536 ECEA1EN100UB CAP E 10UF-25V
C548 ECJ2VF1H103Z CAP C .01UF-Z-50V
C553 ECA1CM101B CAP E 100UF-16V
C554 ECA1VM101B CAP E 100UF-35V
C561 ECA2EHG470E CAP E 47UF-250V
C562 ECKR3A561KBP CAP C 560PF-K-1KV
C563 EEUEB2E330E CAP E 33UF-100V
C564 ECA1VM470B CAP E 47UF-35V
Page
15
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

C566 ECA1VM470B CAP E 47UF-35V
C567 EEUED2C101E CAP E 100UF-100V
C571 ECKRHT332KB CAP C 3300PF-K-
C574 ECA1HM100B CAP E 10UF-50V
C575 ECA1CM101B CAP E 100UF-16V
C576 ECA1CM101B CAP E 100UF-16V
C577 ECQE6473RKF CAP P .047UF-K-600V
C578
ECKW3D681KBR
CAP C 680PF-K-2KV
C581 ECQB1H104JF3 CAP P .10UF-J-50V
C582 ECQB1H104JF3 CAP P .10UF-J-50V
C589 ECQE6184JFB CAP P .18UF-J-600V
C590 ECJ2VB1H471K CAP C 470PF-K-50V
C713 ECKR3A222KBP CAP C .0022UF-K-1KV
C714 ECQE2103KF3 CAP P .010UF-K-200V
C801
ECQU2A224MLA
CAP P .22UF-M-250V
C802
ECQU2A224MLA
CAP P .22UF-M-250V
C803
ECQU2A224MLA
CAP P .22UF-M-250V
C804
ECQU2A224MLA
CAP P .22UF-M-250V
C806
ECQU2A103MLA
CAP P .010UF-M-250V
C807
ECKCNA222MEB
CAP C 2200PF-M-125V
C808
ECKCNA222MEB
CAP C 2200PF-M-125V
C809 ECQB1H471JF3 CAP P 470PF-J-50V
C810 EETHC2D102J CAP E 1000UF-200V
C811 ECA1HM100B CAP E 10UF-50V
C812 ECA1CM471B CAP E 470UF-16V
C813 ECA1HM010B CAP E 1UF-50V
C815 EEUFC1E222E CAP E 2200UF-25V
C821
ECKW3D332KBP
CAP C 3300PF-K-2KV
C822 ECQB1H102JF3 CAP P 1000PF-J-50V
C823 ECQB1H471JF3 CAP P 470PF-J-50V
C824
ECKW3D102KBP
CAP C 1000PF-K-2KV
C825 ECA1HHG470B CAP E 47UF-50V
C826 ECJ2VF1H104Z CAP C .1UF-Z-50V
C827 ECA1HHG010B CAP E 1UF-50V
C828 ECKR3A331KBP CAP C 330PF-K-1KVDC
C830 EC0S2DA471BB CAP E 470UF-200V
C831
ECKW3D102KBP
CAP C 1000PF-K-2KV
C834 EEUFC1H222E CAP E 2200UF-50V
C835 ECA2EM101E CAP E 100UF-250V
C836 ECKR3A151KBP CAP C 150PF-K-1KV
C840 EEUFC1E222E CAP E 2200UF-25V
C841 ECA1VHG222E CAP E 2200UF-35V
C842 ECKR3A331KBP CAP C 330PF-K-1KVDC
C843 ECA1VHG222E CAP E 2200UF-35V
C844 ECKR3A471KBP CAP C 470PF-K-1KV
C846 ECEA1CN101UB CAP E 100UF-16V
C852 ECJ2VF1H103Z CAP C .01UF-Z-50V
C855 EEUFC1A471B CAP E 470UF-10V
C857 ECA1HM471E CAP E 470UF-50V
C858 ECA1CM101B CAP E 100UF-16V
C864 ECEA1CN101UB CAP E 100UF-16V
C867 ECQM4103RJZ CAP P .01UF-J-400V
C871 ECA1CM102B CAP E 1000UF-16V
C875 ECQB1H473JF3 CAP P .047UF-J-50V
C881 ECKR3A471KBP CAP C 470PF-K-1KV
C882 ECA1VHG222E CAP E 2200UF-35V
C901 ECJ2VF1H103Z CAP C .01UF-Z-50V
C902 ECA1CM101B CAP E 100UF-16V
Page
16
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

C904 ECA1CM101B CAP E 100UF-16V
C906 ECA1CM101B CAP E 100UF-16V
C907 ECA2EM220E CAP E 22UF-250V
C908 ECQE2103KF3 CAP P .010UF-K-200V
C909 ECA1CM101B CAP E 100UF-16V
C910 ECA2CM100B CAP E 10UF-160V
C911 ECQE2103KF3 CAP P .010UF-K-200V
C1051 ECJ2VF1H103Z CAP C .01UF-Z-50V
C1052 ECEA1CKA470B CAP E 47UF-16V
C1401 ECJ2VF1H103Z CAP C .01UF-Z-50V
C1402 ECJ2VF1C104Z CAP C .1UF-Z-16V
C1403 ECA1VM470B CAP E 47UF-35V
C1501 ECA1VM470B CAP E 47UF-35V
C1502 ECQB1H103JF3 CAP P .01UF-J-50V
C1505 ECQB1H103JF3 CAP P .01UF-J-50V
C1506 ECQB1H223JF3 CAP P .022UF-J-50V
C1507 ECQB1H223JF3 CAP P .022UF-J-50V
C1522 ECA1VM101B CAP E 100UF-35V
C1523 ECA1VM470B CAP E 47UF-35V
C1526 ECJ2VF1H103Z CAP C .01UF-Z-50V
C1528 ECJ2VF1H103Z CAP C .01UF-Z-50V
C1535 ECA1HM100B CAP E 10UF-50V
C1557 ECQB1H102JF3 CAP P 1000PF-J-50V
C1558 ECJ2VC1H680J CAP C 68PF-J-50V
C1559 ECQB1H102JF3 CAP P 1000PF-J-50V
C1570 ECA1VM470B CAP E 47UF-35V
C2202
ECEA1HKA2R2B
CAP E 2.2UF-50V
C2203
ECEA1HKA4R7B
CAP E 4.7UF-50V
C2204 TAP106K016CF CAP T 10MF-16V
C2205 ECEA1HKA010B CAP E 1.0UF-50V
C2206 ECQB1H223JF3 CAP P .022UF-J-50V
C2207 TAP335K016CF CAP T 3.3 MF-16V
C2208 ECJ2VB1C104K CAP C .1UF-K-16V
C2209 ECJ2VB1C104K CAP C .1UF-K-16V
C2210 ECJ2VB1C104K CAP C .1UF-K-16V
C2211 ECEA1HKA100B CAP E 1UF-50V
C2212 ECQB1H473JF3 CAP P .047UF-J-50V
C2215 ECEA1CKA101B CAP E 100UF-16V
C2218
ECEA1HKAR47B
CAP E .47UF-50V
C2301 ECJ2VF1C474Z CAP C .47UF-Z-16V
C2302 ECJ2VB1H561K CAP C 560PF-K-50V
C2303 ECJ2VB1H332K CAP C .0033UF-K-50V
C2304 ECJ2VB1H332K CAP C .0033UF-K-50V
C2305 ECJ2VF1C474Z CAP C .47UF-Z-16V
C2306 ECJ2VB1H561K CAP C 560PF-K-50V
C2307 ECJ2VB1H332K CAP C .0033UF-K-50V
C2308 ECJ2VB1H332K CAP C .0033UF-K-50V
C2310 ECJ2VF1H104Z CAP C .1UF-Z-50V
C2312 ECA1VM101B CAP E 100UF-35V
C2316 ECJ2VF1H104Z CAP C .1UF-Z-50V
C2317 ECJ2VF1H104Z CAP C .1UF-Z-50V
C2319 ECJ2VC1H330J CAP C 33PF-J-50V
C2322 ECJ2VF1C474Z CAP C .47UF-Z-16V
C2324 ECJ2VF1C474Z CAP C .47UF-Z-16V
C2326 ECJ2VF1H104Z CAP C .1UF-Z-50V
C2327 ECA1HM010B CAP E 1UF-50V
C2328 ECA1EM101B CAP E 100UF-25V
C2329 ECJ2VF1H103Z CAP C .01UF-Z-50V
C2331 ECA1EM101B CAP E 100UF-25V
Page
17
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

C2332 ECJ2VB1H472K CAP C .0047UF-K-50V
C2333 ECJ2VB1H472K CAP C .0047UF-K-50V
C2350 ECQV1H105JL3 CAP P 1.0UF-J-50V
C2351 ECJ2VB1H152K CAP C .0015UF-K-50V
C2352 ECJ2VB1H152K CAP C .0015UF-K-50V
C2353 ECQV1H105JL3 CAP P 1.0UF-J-50V
C2354 ECJ2VB1H152K CAP C .0015UF-K-50V
C2355 ECJ2VB1H152K CAP C .0015UF-K-50V
C2356 ECA1HM4R7B CAP E 4.7UF-50V
C2357 ECJ2VF1H104Z CAP C .1UF-Z-50V
C2358 ECJ2VF1H224Z CAP C .22UF-Z-50V
C2361 ECJ2VF1H224Z CAP C .22UF-Z-50V
C2364 ECA1HM220B CAP E 22UF-50V
C2365 ECJ2VF1H224Z CAP C .22UF-Z-50V
C2366 ECJ2VF1H224Z CAP C .22UF-Z-50V
C2370 ECA1CM101B CAP E 100UF-16V
C2371 ECA1CM101B CAP E 100UF-16V
C2372 ECEA1CN100UB CAP E 10UF-16V
C2373 ECA1HM100B CAP E 10UF-50V
C2374 ECA1HM100B CAP E 10UF-50V
C2375 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2376 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2377 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2378 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2379 ECJ2VF1H103Z CAP C .01UF-Z-50V
C2380 ECEA1CN100UB CAP E 10UF-16V
C2387 EEUFC1E222E CAP E 2200UF-25V
C2390 EEUFC1E222E CAP E 2200UF-25V
C2451 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2452 ECJ2VB1H472K CAP C .0047UF-K-50V
C2453 ECJ2VB1H223K CAP C .022UF-K-50V
C2454 ECJ2VB1H332K CAP C .0033UF-K-50V
C2455 ECJ2FB1C684K CAP C .68UF-Z-16C
C2456 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2457 ECJ2VB1C104K CAP C .1UF-K-16V
C2458 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2459 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2460 ECJ2VB1H103K CAP C .01UF-K-50V
C2461 ECA1CM221B CAP E 10UF-16V
C2462 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2463 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2464 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2465 ECJ2VB1C104K CAP C .1UF-K-16V
C2466 ECJ2FB1C684K CAP C .68UF-Z-16C
C2467 ECJ2VB1H332K CAP C .0033UF-K-50V
C2468 ECJ2VB1H223K CAP C .022UF-K-50V
C2469 ECJ2VB1H472K CAP C .0047UF-K-50V
C2470 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C2471 ECA1CM471B CAP E 470UF-16V
C2851 ECA1EM471B CAP E 470UF-25V
C2852 ECA1CM221B CAP E 10UF-16V
C2855 ECA1VM221B CAP E 220UF-35V
C2857 EEUFC1C471B CAP E 470UF-16V
C2859 ECJ2VF1H103Z CAP C .01UF-Z-50V
C2861 EEUFC1A471B CAP E 470UF-10V
C2862 ECA1HM471E CAP E 470UF-50V
C2865 ECA1EM221B CAP E 220UF-25V
C2867 EEUFC1A471B CAP E 470UF-10V
C2868 ECA0JM222B CAP E 2200UF-6.3V
Page
18
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

C2869 ECJ2VF1H103Z CAP C .01UF-Z-50V
C2870 ECA1EM221B CAP E 220UF-25V
C2872 EEUFC1A471B CAP E 470UF-10V
C2874 ECJ2VF1H103Z CAP C .01UF-Z-50V
C2881 ECJ2VB1H103K CAP C .01UF-K-50V
C2882 ECJ2VB1H103K CAP C .01UF-K-50V
C3331 ECJ2VB1H152K CAP C .0015UF-K-50V
C3332 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3333 ECJ2VB1H152K CAP C .0015UF-K-50V
C3334 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3335 ECJ2VB1H152K CAP C .0015UF-K-50V
C3336 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3337 ECJ2VB1H152K CAP C .0015UF-K-50V
C3338 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3339 ECJ2VB1H103K CAP C .01UF-K-50V
C3340 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3341 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3342 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3343 ECJ2VB1H152K CAP C .0015UF-K-50V
C3344 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3345 ECJ2VB1H152K CAP C .0015UF-K-50V
C3346 ECJ2VB1H103K CAP C .01UF-K-50V
C3347 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3348 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3349 ECJ2VB1H152K CAP C .0015UF-K-50V
C3350 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3351 ECJ2VB1H152K CAP C .0015UF-K-50V
C3352 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3353 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3354 ECJ2VB1H152K CAP C .0015UF-K-50V
C3355 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3357 ECJ2VB1H152K CAP C .0015UF-K-50V
C3358 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3359 ECA1EM471E CAP E 470UF-25V
C3360 ECJ2VB1H152K CAP C .0015UF-K-50V
C3361 ECJ2VB1H152K CAP C .0015UF-K-50V
C3362 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3363 ECJ2VF1C105Z CAP C 1.0UF-Z-16V
C3364 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3365 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3366 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3367 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3368 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3369 ECJ2YB1A105K CAP C 1.0UF-K-125V
C3401 ECJ2VB1H152K CAP C .0015UF-K-50V
C3402 ECJ2VB1H152K CAP C .0015UF-K-50V
C3405 ECA1HM010B CAP E 1UF-50V
C3406 ECA1HM010B CAP E 1UF-50V
C3801 ECQE2104KFW CAP P .10UF-K-200V
C3802 ECQE2104KFW CAP P .10UF-K-200V
C3803 ECQE2104KFW CAP P .10UF-K-200V
C3807 ECA2EM470E CAP E 47UF-250V
C3808 ECA2EM470E CAP E 47UF-250V
C3809 ECA2EM101E CAP E 100UF-250V
C3810 ECA2EM101E CAP E 100UF-250V
C3811 ECKC3D332KBN CAP C 3300PF-K-2KV
C456A ECJ2VB1H472K CAP C .0047UF-K-50V
C468A ECJ2VB1H331K CAP C 330PF-K-50V
C469A ECJ2FB1H104K CAP C .1UF-K-50V
Page
19
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...

C502A ECJ2VF1H104Z CAP C .1UF-Z-50V
C503A ECJ2VB1H102K CAP C .001UF-K-50V
CF803 D4DDF1R50001 DIODE
DIODES
D005 MA3X152K0L DIODE
D009 MA2C165001VT DIODE
D012 MAZ40360MF DIODE ZENER
D460 MA2C165001VT DIODE
D461 MA2C165001VT DIODE
D462 MAZ40300MF DIODE ZENER
D463 MA2C165001VT DIODE
D465 MAZ40390MF DIODE ZENER
D466 MA2C165001VT DIODE
D468 MA2C165001VT DIODE
D469 MAZ40300MF DIODE ZENER
D470 MA2C165001VT DIODE
D501 MAZ41500MF DIODE ZENER
D502 MAZ41500MF DIODE ZENER
D503 B0HALP000007 DIODE FAST RECOVERY
D506 B0JAME000058 DIODE SCHOTTKY BARR
D507 B0JAME000058 DIODE SCHOTTKY BARR
D508 B0HAGV000004 DIODE FAST RECOVERY
D509 MA2C165001VT DIODE
D510 MAZ40820MF DIODE ZENER
D511 B0EALV000001 DIODE RECTIFIER
D513 MAZ42700MF DIODE ZENER
D518 MA2C165001VT DIODE
D521 MAZ41800MF DIODE ZENER
D522 B0AAGR000002 DIODE SWITCHING
D523 B0HASV000002 DIODE
D524 MA2C165001VT DIODE
D525 B0HALP000007 DIODE FAST RECOVERY
D528 B0HALP000007 DIODE FAST RECOVERY
D533 MA2C700A0F DIODE
D534 MA2C165001VT DIODE
D539 MA2C165001VT DIODE
D540 B0HALP000007 DIODE FAST RECOVERY
D541 B0JAME000058 DIODE SCHOTTKY BARR
D584 MA2C165001VT DIODE
D701 MA2C029TAF DIODE
D702 MA2C029TAF DIODE
D801 B0FBAT000006 DIODE RECTIFIER
D804 B0EBKM000023 DIODE RECTIFIER
D807 MA2C165001VT DIODE
D809 ERZV10D391 VARISTOR SURGE ABSORBER
D811 B0EAKL000008 DIODE RECTIFIER
D814 MA2C165001VT DIODE
D815 MA2C165001VT DIODE
D816 MA2C165001VT DIODE
D817 MAZ42200LF DIODE ZENER
D819 MA2C165001VT DIODE
D820 B0HAGM000005 DIODE FAST RECOVERY
D822 B0HAMM000036 DIODE FAST RECOVERY
D823 MAZ406800F DIODE ZENER
D824 B0BA01000070 DIODE VOLTAGE REGULATOR
D825 B0HANR000003 DIODE FAST RECOVERY
D827 B0HANM000038 DIODE FAST RECOVERY
D828 MA3D690 DIODE
D829 B0HAMM000124 DIODE
Page
20
of
32
7/7/2008
http://tsn.pstc.panasonic.com/viewing/NA/CT
-
27HL15N/SIMP/MTNC050426A1/doc/MTN
...