Panasonic mc-e7101 User manual

©2004 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
MC-E7101
MC-E7103
Product Color (R)Red---MC-E7101 (B)Blue---MC-
E7101 (R)Red---MC-E7103
Destination Europe
Vacuum Cleaner
Specifications
Order No. ECD0405001C2

1 Name of parts
MODEL MC-E7103, MC-E7101
3
MC-E7101 / MC-E7103

4
MC-E7101 / MC-E7103

4 TROUBLE SHOOTING GUIDE
CONDITION CHECHPOINT METHOD OF INSPECTION CAUSE/REMEDY
Motor fails rotate
(no noise heard at all). Power cord connection Chech power cord continuity between pliug pins cord reel ass´y. If there is no continuity, replace the cord reel ass´y.
Fuse (250V, 12A) Chech fuse continuity. If there is no continuity, replace
the fuse.
Motor continuity Chech motor contiuity between
carbon brush holder tabs. If there is no continuity, replace the motor.
On/OFF Switch Chech continuity across switch
connections. If there is no continuity, replace ON/OFF Switch.
Theamal cut-out Chech continuity across themal
cut-out tabs. connections. If there is no continuity, replace thermal cut-out.
Triac Chech if the triac is in open circuit. If it is in open circuit,
replace power control circuit.
Motor runs but there is no suction. Hose or Suction inlet Chech if there any blockage in the
hose or suction inlet. lf therer is any blockage, remove it.
Dust bag / Central filter Chech if dust bag is full or dust
accumulated in central filter. If the paper bag is full, replace it. If the central filter is dirt, clean or
replace it.
Noise or vibration Motor fan Chech dust accumulated in motor
fan (it could happen if the vacuum
cleaner has been used with a
broken dust bag or without central
filter).
if the is dust accumulated in the
motor fan, replace the motor and
chech filter condition (never try to
dismantle the motor fan).
6
MC-E7101 / MC-E7103

IMPORTANT: Before replacing any part always
DISCONNECT THE CLEANER FROM THE ELECTRICITY
SUPPLY.
5.1. Removing attachment nozzle
and rear cover
1.Remove the nozzle and rear cover.
5.2. Removing dust cover unit
1.Keeping the dust cover unit open, insert the minus
screwdriver into the left (right) hinge area (clearance
between dust cover unit and upper body). Using the minus
screwdriver as the lever, pry off the dust cover unit for
removal.
2.Also on the right (left) hinge area, similarly insert the minus
screwdriver and remove the hinge area of the dust cover
unit.
3.Take the revers order of removing procedure.
5.3. Disassemble of Dust Cover
Assembly
5.3.1. Suction Inlet unit
1.Removing
Remove the mounting screw(3pieces),and remove Suction
Inlet unit.
2.Assembling
Take the revers order of removing procedure.
5.3.2. Indicator unit
1.Removing
Remove the mounting screw(1pieces),and remove Indicator
uni.
2.Assembling
Take the revers order of removing procedure.
5 REPLACEMENT OF MAIN PARTS
7
MC-E7101 / MC-E7103

5.4. Removing upper body
1.Remove the mounting screw (1 piece), and remove the rear
cover retaining plate.
2.Lifting the handle at the rear area, and push it forward for
removal.
3.Reverse the main body of the cleaner upside down, and
remove the mounting screws (2 pieces) of the upper body
on the rear of the main body.
* Special screws are sometimes used.
(If a TORX screwdriver is not available, you can use a
narrow flat-blade screwdriver to remove it.)
4.Return the main body downside up, remove the mounting
screws (4 pieces) of the upper body, and remove the upper
body from the lower body.
5.5. Replacing motor
1.Straightly pull up the motor from the lower body for removal.
2.Disconnect Faston connection terminal from the motor.
3.Disassemble of Fan Motor unit.
Remove the front and rear motor support rubber and noise
suppressor, etc., and replace the motor.
4.Assembling
Take the revers order of removing procedure.
8
MC-E7101 / MC-E7103

5.6. Replacing cord reel
1.When the motor is removed from the lower body, straightly
pull up the cord reel from the lower body for removal.
2.Disconnect the lead wires from the connection terminals
(Faston terminals) of the cord reel on the body partition.
3.Pull up and remove the power supply cord cover of the
lower body, and disconnect the cord.
4.Pro-wind the cord reel ass’y 4 or 5 times in the direction of
the arrow (→) indicated on the cord reel cover.
5.With the brake lever section down, fit the cord reel ass’y
into the upper body.
6.After positioning the lead wrie between the motor and body
partition, couple the lower body.
*We will provide a cord reel for units for the UK market
together with a lower body unit as a set, because its plug is
big. (lower body unit)
9
MC-E7101 / MC-E7103

5.7. Replacing power switch
1.Remove the lead wires and hole cover from the connection
terminal (Faston terminal).
2.Disengage the hook of the switch button from the lib inside
the upper body, and remove the switch.
NOTE:Make sure the lead wires and lower body seal are
correctly positioned to avoid pinching them between parts.
5.8. Replacing power board
1.Look at inside the upper body.
2.Disconnect the lead wires from the switch terminals.
3.Remove the power board fastening screws (2 pieces), and
remove the power board from the upper body.
5.9. Replacing current fuse
1.Disconnect the screw connectors on both ends of the
current fuse, and replace the current fuse.
2.When reconnecting after repair, verify that they are securely
connected.
10
MC-E7101 / MC-E7103

6.1.2. PARTS LIST (ATTACHMENT)
Ref. No. Part No. Part Name & Description Remarks
A-1 AMC99R-UW0 FLOOR NOZZLEASSY.(PLASTIC)
A-2 AMC94P-UW0 HOSE ASSENBLY
A-3 AMC13P-UW0 ENTENSION WAND A(PLASTIC) E7101
A-3 AMC13P-UX0 ENTENSION WAND A(METAL) E7103
A-4 AMC40P-UW0 ENTENSION WAND (PLASTIC) E7101
A-4 AMC40P-UX0 ENTENSION WAND (METAL) E7103
12
MC-E7101 / MC-E7103

6.1.4. PARTS LIST (BODY UNIT)
Ref. No. Part No. Part Name & Description Remarks
B-1 AMC01B-UW0B HANDLE E7101 BLUE
B-1 AMC01B-UW0R HANDLE E7101/E7103 RED
B-2 AMC93K-UW0B DUST COVER ASSEMBLY E7101 BLUE
B-2 AMC93K-UW0R DUST COVER ASSEMBLY E7101 RED
B-2 AMC93K-UX0R DUST COVER ASSEMBLY E7103 RED
B-3 AMC92L-UW0B DUST COVER UNIT E7101 BLUE
B-3 AMC92L-UW0R DUST COVER UNIT E7101 RED
B-3 AMC92L-UX0R DUST COVER UNIT E7103 RED
B-4 AMC30D-UW0B HINGE E7101 BLUE
B-4 AMC30D-UW0R HINGE E7101/E7103 RED
B-5 AMC38D-UW0 HINGE SPRING
B-6 AMC98M-UW0 INDICATOR UNIT
B-7 XTN4+12AFY TAPPING SCREW
B-8 AMC96H-UW0 SUCTION INLET UNIT
B-9 XTN4+12AFY TAPPING SCREW
B-10 AMC02A-UW0B UPPER BODY E7101 BLUE
B-10 AMC02A-UW0R UPPER BODY E7101/E7103 RED
B-11 AMC46N-UW0V BRAKE PEDAL
B-12 AMC08E-UW0 SWITCH SPRING
B-13 AMC05E-UW0V SWITCH PEDAL
B-14 AMC03E-UW0K SWITCH COVER
B-15 AMC01E-UW0 ON/OFF SWITCH
B-16 XTW3+10AFY TAPPING SCREW
B-17 XTN4+16AFY TAPPING SCREW
B-18 AMC03L-UW0 PACKING A
B-19 AMC24A-UW0B BODY COVER E7101 BLUE
B-19 AMC24A-UW0R BODY COVER E7101/E7103 RED
B-20 XTN4+16AFY TAPPING SCREW
B-21 AMC01L-UW0B REAR COVER E7101 BLUE
B-21 AMC01L-UW0R REAR COVER E7101/E7103 RED
B-22 AMC38K-UW0 EXHAUST FILTER
B-23 AMC89V-UW0 PRINTED CIRCUIT BOARD A UNIT
B-24 AMC02F-UW0 MOTOR SUPPORT RUBBER FRONT
B-25 AMC14F-UW0 MOTOR CASE RUBBER (NR)
B-26 AMC92F-UW00C FAN MOTOR UNIT E7101 240V
B-26 AMC92F-UW00E FAN MOTOR UNIT E7101 230V
B-26 AMC92F-UX00C FAN MOTOR UNIT E7103 240V
B-26 AMC92F-UX00E FAN MOTOR UNIT E7103 230V
B-27 AMC03F-UW0 MOTOR SUPPORT RUBBER REAR
B-28 AMC99G-UW0 NOISE SUPPRESSOR UNIT
B-29 AMC99K-UW0 CLOTH BAG UNIT
B-30 AMC16K-UW0 PAPER BAG
B-31 AMC10K-UW0Y BAG SUPPORTER
B-32 AMC66K-UW0 DUST COVER PACKING
B-33 AMC03A-UW0V LOWER BODY
B-34 AMC01C-UW0V WHEEL
B-35 AMC22K-UW0V BAG CLAMPER
B-36 AMC46H-UW0 BAG CLAMPER SPRING
B-37 XTW3+10AFY TAPPING SCREW
B-38 AMC37K-UW0 SECONDARY FILTER
B-39 AMC14N-UW0V CORD GUIDE
B-40 AMC97A-UW08 LOWER BODY U (with cord reel) with cord reel(BF PLUG)UK only
B-40-1 AMC91N-UW00E CORD REEL ASSEMBLY with SE PLUG
B-40-2 AMC91N-UW00L CORD REEL ASSEMBLY with C2 PLUG
B-41 AMC16N-UW0V GRIP COVER
B-42 AMC15N-UW0 CORD GUIDE SHAFT
B-43 AMC81A-UW0 TIGHT PACKING
B-44 AMC19A-UW0 BODY PACKING
B-45 NAME PLATE It can not supply.
B-46 AMC88C-UW0 BODY ROLLER UNIT
B-47 XTN4+12AFY TAPPING SCREW
B-48 AMC95C-UW0 CASTER UNIT
B-49 AMC68A-UW0 SCREW
B-50 AMC60R-UW0V CREVICE TOOL
B-51 AMC65R-UW0V DUSTING BRUSH
14
MC-E7101 / MC-E7103

6.1.5. PACKING INSTRUCTION
15
MC-E7101 / MC-E7103

6.1.6. PACKING LIST
Ref. No. Part No. Part Name & Description Remarks
C-1 AMC61Z-UW0BA CARTON BOX E7101 BLUE
C-1 AMC61Z-UB0RA CARTON BOX E7101 RED
C-1 AMC61Z-UX0RA CARTON BOX E7103 RED
C-2 AMC98Z-UW0 CUSHION UNIT E7101
C-2 AMC98Z-UX0 CUSHION UNIT E7103
C-3 AMC10Z-UW0 BODY BAG
C-4 AMC49Z-UW0 PARTITION BOARD A
16
MC-E7101 / MC-E7103