Panasonic NA-F60A6 User manual

Order No. PHAT070402C3
(Revision : May. 2011)
Service Manual
Fully Automatic Washing Machine
NA-F60A6
NA-F70A6
NA-F756A
NA-F70G6
NA-F70G6P
NA-F70X6
NA-F806X
Product Colour
Silver, Grey, White
Destination
Thailand, Indonesia, Singapore
Philippines, Malaysia, UAE, Oman
Kuwait, Qatar, Taiwan, Singapore (Exp.)
© Panasonic Home Appliances (Thailand) Co., Ltd. 2007.
All rights reserved. Unauthorized copying and distribution
is a violation of law.
There are special components used in this equipment which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Diagrams, Exploded Views and Replacement Parts List. It is essential that
these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do
not modify the original design without permission of manufacturer.
IMPORTANT SAFETY NOTICE
WARNING
The service information is designed for experienced repair technicians only and is not designed for use by the general
public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting
to service a product. Products powered by electricity should be serviced or repaired only by experienced professional
technicians. Any attempt to service or repair the product or products dealt within this service information by anyone
else could result in serious injury or death.

- 2 -
CONTENT
Page
3
4 - 5
6 - 7
8 - 9
10 - 11
12
13 - 15
16 - 18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
35
36
36
1. Attention in the Repair Work Security
2. Specification
3. Features and Technical Information
4. Installation
5. Operations Panel
6. Wiring Diagram
7. Table of Errors
8. Troubleshooting
9. Parts Exploded View and Replacement Parts List
9.1 Parts Exploded View : A
9.2.1 Replacement Parts List : A for NA-F60A6
9.2.2 Replacement Parts List : A for NA-F70A6 / NA-F756A
9.2.3 Replacement Parts List : A for NA-F70G6 / NA-F70G6P
9.2.4 Replacement Parts List : A for NA-F70X6 / NA-F806X
9.3 Parts Exploded View : B
9.4.1 Replacement Parts List : B for NA-F60A6
9.4.2 Replacement Parts List : B for NA-F70A6 / NA-F756A
9.4.3 Replacement Parts List : B for NA-F70G6 / NA-F70G6P
9.4.4 Replacement Parts List : B for NA-F70X6 / NA-F806X
9.5 Parts Exploded View : C
9.6.1 Replacement Parts List : C for NA-F60A6
9.6.2 Replacement Parts List : C for NA-F70A6 / NA-F756A
9.6.3 Replacement Parts List : C for NA-F70G6 / NA-F70G6P
9.6.4 Replacement Parts List : C for NA-F70X6 / NA-F806X
9.7 Parts Exploded View : Packing
9.8.1 Replacement Parts List : Packing for NA-F60A6
9.8.1 Replacement Parts List : Packing for NA-F70A6 / NA-F756A
9.8.1 Replacement Parts List : Packing for NA-F70G6 / NA-F70G6P
9.8.1 Replacement Parts List : Packing for NA-F70X6 / NA-F806X
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
Usage : For repairs and change of spare part only for washing machine type Panasonic Model
NA-F60A6 / NA-F70A6 / NA-F756A / NA-F70G6 / NA-F70G6P / NA-F70X6 / NA-F806X
Instructin for
Usage
: The work repair and changing of space part should be operated by a skilled technician from
the distribution agents or Panasonic’s Standard Service Center.
Warning : Switch off electrical power before commencing work to avoid a potential short circuit or injury.

- 3 -
1. ATTENTION IN THE REPAIR WORK SECURITY
Please wear gloves when disassembling, replacing and assembling.
Always wear gloves to prevent an injury by the metal end face or an electric shock at the
time of the electricity service.
Please be careful to the edges of the metal end face.
Wear the working clothes of long sleeves to prevent an injury by the metal end face or
replease work after covering the end face with tape or towel.
Rebuilding is prohibited.
Do not reguild machine parts and
components when repairing service. It
may be the cuase of damage or ignition.
Straightly pull out or insert in huasuton terminal.
Do not twist it.
It may be the cause of damage or ignition.
Be sure to use specified parts.
Always use specified parts for the parts
with mark in the electric circuit
diagrams and parts list. It may be the
cause of smoke, ignition or damage.
Do not touch any rotating object with hand unless
it stops completely.
Slow rotation may also roll in your hands and
cause injury.
Be careful about receiving an electric shock.
When doing electric connection service
such as voltage measurement, please
be careful enough about receiving an
electric shock at electric charging parts
and cable terminal parts.
Pull out electric plug when doing repair work.
Disassembling, assembling and replacing
parts should be done after pulling out
electric plug. Receiving an electric shock
or getting an injury may occur.
In order to prevent any accident during repair work and ensure security of the product after repair work,
somethings surely followed are explained below.
Connection of cables should be done according to regular work.
• Connection of cables should be tightened reliably with strength using solderless terminal.
(specified parts always using regular bonding plier)
• Install a fire protection cover (fireproof) covering connection area completely, and close
opening area by tape. (Please reuse the fire protection cover which came with the product.)
• When drawing cables around, fixing those cables with cable suppression part. Do not touch
rotating part, high temperature part and surface of metal.
• Be sure to replace with cable unit when any cable was snapped. When a part of the cable
unit was cut you must not do the connection repair. It may be the cause of smoke, ignition
or receiving an electric shock.
■ Types of the contents being followed are classified by following figured symbols and explained.
(The following is an example of expression in pictures.)
Warning
Attention
Warning
Attention
This figured symbol means caution "Attention".
This figured symbol means must not do "Prohibition".
This figured symbol means surely execute "Instructions".
■ The level of the arised damages or dangers, when indicated contents are ignored, are classified by
following indications and explained.
The content in the column of this indication is
"Be assumed that possibly die or get seriously injured".
The content in the column of this indication is
"Be assumed that possibly get damages or possibly only damaged object occured".
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X

- 4 -
2. SPECIFICATIONS
2.1 Specifications
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
MODEL NA-F60A6 NA-F70A6 NA-F756A NA-F70G6 NA-F70G6P NA-F70X6 NA-F806X
Rate Voltage and Frequency -110V/60Hz Taiwan -----
Singapore230V/50Hz Singapore - Singapore - Singapore -
Thailand
Indonesia
220V/50Hz Thailand
Singapore
(Exp.)
Indonesia Thailand
UAE (Exp.)
UAE (Exp.) Thailand
UAE (Exp.)
Indonesia
Indonesia
Philippines230V/60Hz ----Philippines -
Malaysia
MID East
(UAE, Oman
Kuwait, Qatar)
240V/50Hz Malaysia - Malaysia MID EAST
(UAE-ONE
Kuwait, Qatar)
Malaysia Indonesia
-110V/60HzRate Power Consumption
Standard Water Consumption
420420----
Grey / WhiteColour Grey / White Silver / White White Silver
420230V/60Hz ----430430
410240V/50Hz 435 435 410
0.03 to 1 Mpa (0.3 to 10 Kgf/cm )
0.3 - 10 Kgf/cm (8-25 liter/min)
583 x 572 x 982 (mm)
137 Liter 155 Liter
Standard Capacity 6 Kgs 7 Kgs
Water Supply Pressure
Outer Dimension
583 x 572 x 982 (mm)External Dimension
Checking unbalance / Tub lidSafety Switch
Rings when finishing washing or unusualAlarm
MotorThermo Protector
YesWater Inlet Hole
YesFabric Softener Dispenser
Bleach Dispenser
YesFilter
YesAutomatic Power-cut Switch
Inlet pipe (1.2 m), Tab joint, Drain pipe (80 cm), Rat prevention screenAccessories
110V/60Hz : Taiwan
240V/50Hz : Malaysia, MID EAST (UAE, Oman, Kuwait, Qatar)
230V/60Hz : Philippines
230V/50Hz : Singapore
220V/50Hz : Thailand, Indonesia, Singapore (Exp.), UAE (Exp.)
Voltage (AC)
Weight 30 Kgs 33 Kgs
Water Consumption (Normal Program) 137 Liter 155 Liter
Water Pressure
Pulsator (r.p.m.) 100 r/min 110 r/min
No Yes
410 410 410
410220V/50Hz 435 435 390 390 390 390
2
2
775 r/minSpin Tub (r.p.m.)
Machine Weight 30 Kgs 33 Kgs
Motor Power Input : 320W
Output : 410W
Input : 320W
Output : 435W

- 5 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
2.2 Standard Water Consumption
■ NA-F60A6
■ NA-F70A6 / NA-F756A / NA-F70G6 / NA-F70G6P
WASH LEVEL WATER
56 Liters
CLOTHES WEIGHT
7.0 Kgs 51 Liters
45 Liters 3.5 Kgs 41 Liters
32 Liters 1.5 Kgs 30 Liters
18 Liters 0.5 Kgs 16 Liters
High
Medium
Low
Extra - Low
■ NA-F70X6 / NA-F806X
WASH LEVEL WATER
74 Liters
CLOTHES WEIGHT
9.0 Kgs 68 Liters
69 Liters 6.0 Kgs 62 Liters
62 Liters 5.0 Kgs 57 Liters
58 Liters 4.2 Kgs 53 Liters
High
< High Lower >
Medium
< Medium Lower >
52 Liters 3.5 Kgs 49 Liters
48 Liters 2.5 Kgs 45 Liters
Low
< Lower 1 Lower >
42 Liters 1.5 Kgs 40 Liters
38 Liters 1.1 Kgs 35 Liters
Low 2
< Lower 2 Lower >
32 Liters 0.8 Kgs 30 Liters
16 Liters 0.3 Kgs 16 Liters
Low 3
< Lower 3 Lower >
WASH LEVEL WATER
53 Liters
CLOTHES WEIGHT
6.0 Kgs 45 Liters
39 Liters 3.0 Kgs 35 Liters
32 Liters 1.5 Kgs 30 Liters
18 Liters 0.5 Kgs 16 Liters
High
Medium
Low
Extra - Low

- 6 -
3. FEATURES AND TECHNICAL INFORMATION
3.1 Product special feature
3.2 Weight sensor
The weight is sensed by the moving force of the Pulsator, which
changes a capacitor pole and releases a signal wave. The wave
is changed into a pulse number from which the clothes weight is
sensed. Prior to weight sensing for Normal and Strong program,
the machine runs without water by spinning the Pulsator to left
and right for 4.2 seconds (ON 0.3 second - OFF 0.4 second).
The motor stops (OFF), a water system counts the pulse number,
then calculates the accumulated pulse numbers for drawing
water into the tub over a defined level. The dial will indicate High
wash level.
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
■ NA-F70A6 / NA-F756A / NA-F70G6 / NA-F70G6P
Program Time
Approx. 40 - 59 min
• Pre-wash weight sensor.
• Pre-set timer.
• Fabric softener dispenser.
• Detergent dispenser.
• Automatic power-off when finish.
• Dial indicating unusual sign (LED will blink).
• Overflow sensing device.
• Dial indicating time remaining.
• Dial indicating detergent level after sensing wash level.
Normal
Approx. 21 - 37 minSpeedy
Approx. 24 - 29 minDelicate
Approx. 36 minTub Dry
Approx. 100 - 119 minSoak 1 hour
Approx. 219 - 238 minSoak 3 hour
Approx. 511 - 530 minSoak 8 hour
■ NA-F70X6 / NA-F806X
Program Time
Approx. 46 - 60 min
• Pre-wash weight sensor.
• Pre-set timer.
• Fabric softener dispenser.
• Detergent dispenser.
• Automatic power-off when finish.
• Dial indicating unusual sign (LED will blink).
• Overflow sensing device.
• Dial indicating time remaining.
• Dial indicating detergent level after sensing wash level.
Normal
Mini Approx. 15 min
New Speedy Approx. 37 - 53 min
Delicate
Blanket Approx. 47 - 55 min
Tub Hygiene
Approx. 23 min
Soak 1 hour
Approx. 150 min
Soak 3 hour
Approx. 61 min
Approx. 179 min
Approx. 471 minSoak 8 hour
■ NA-F60A6
Program Time
Approx. 40 - 59 min
• Pre-wash weight sensor.
• Pre-set timer.
• Fabric softener dispenser.
• Detergent dispenser.
• Automatic power-off when finish.
• Dial indicating unusual sign (LED will blink).
• Overflow sensing device.
• Dial indicating time remaining.
• Dial indicating detergent level after sensing wash level.
Normal
Approx. 37 - 53 minSpeedy
Approx. 23 minDelicate
Approx. 36 minTub Dry
Approx. 61 minSoak 1 hour
Approx. 179 minSoak 3 hour
Approx. 471 minSoak 8 hour
High Medium Low
Low Pulse Number High

- 7 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
3.3 Function control with fuzzy sensor
Clothes quantity checking, wash level indication and detergent consumption indication with Fuzzy Logic System.
1. Check clothes quantity and specify the amount of detergent.
2. Temperature checking.
Check temperature in the atmosphere when the machine starts.
In case of low temperature, wash timer and spin timer are extended
automatically, so that washed clothes are as clean as washing in
high temperature.
1. Wash timer and spin timer with checked clothes quantity.
2. Additional wash timer and spin timer as temperature increases.
Rotate clockwise
stop
< Motor Status >
Rotate
anti-clockwize
Turn Switch “ON”
Press “Start” button
1. Check clothes quantity
2. Check ambient temperature
A. Check clothes quantity
B. Control wash time
C. Control spin time
Supply water to a proper level
WASH
RINSE
SPIN
Switch will automatically cut the
power current “OFF”
< Checking Method >
Check cross pressure at the capacitor
while the Pulsator operates without water.
stop
Rotate clockwise
stop
Rotate
anti-clockwize
stop
Rotate clockwise
stop
Rotate
anti-clockwize
stop
High
3.0 Kg and more
Medium
1.2 Kg ~3.0 Kg
Low
0 Kg ~1.2 Kg
Wash Timer 12 min 12 min 9 min
Spin Timer 6 min 6 min 5 min
External Temp. 25°C 15°C 5°C 30°C
Wash Timer +0 min +2 min +3 min -1 min
Spin Timer +0 min +1 min +2 min +0 min

- 8 -
4. INSTALLATION
4.1 Checking of placement
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
45
Hose extension
If extended external part is necessary when connecting the drain hose, the length of the drain hose should be
less than 3 m and the height should be below 10 cm.
Install the machine 10 cm or more away from the wall.
Elbow
Water supply
valve screw
Water supply hose
Drain hose
Nut
3 m max.
Do not put hose tip
under the water
Over 10 cm
Good Example
Below 10 cm
Connect the water supply hose to the
water supply valve screw.
[ Cautions ]
Firmly tighten the nut, otherwise water
leakage will result.
Water Pressure Rating :
2.9 x 10 ~ 9.8 x 10 Pa
1. Push the water supply hose nut straights
onto the water supply valve screw.
2. Hold the elbow bny lifting it up, screw the
nut onto the water supply valve screw,
and firmly tighten the nut.
3. After the nut is tightened, check whether
or not the elbow is unsteady or loose.
4. After tightening, open the faucet to confirm
that there is no water leakage.

- 9 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
4.2 Connect the water supply hose
4.3 Install washing machine to steady
4.4 Child Lock program
Adjust height of leg
If the floor is largely inclined.
Use board or
a like for prop
up under leg
of washing
machine.
1. Turn the adjustable leg knob towards (Loosen)
direction to loose it.
2. Turn the adjustable leg to adjust the levelness.
2.1 When increasing height, turn adjustable leg
towards (Loosen) direction.
2.2 When decreasing height, turn adjustable leg
towards (Tighten) direction.
3. Turn the adjustable leg knob towards (Tighten)
direction to tighten it.
[ Note ]
- Firmly tighten part B of the water tap adaptor,
otherwise, water leakage will result.
- When the hose must be reinstalled (after you remove).
For example, turn B to the left until about 4 min., of the
thread becomes visible, then carry out the procedure
described above.
- If a water tap adaptor is already connected, replace
with the attached new one.
Press the [ POWER OFF/ON ] button for at least
5 seconds. The buzzer sounds (2 times for setting)
and the [ CHILD LOCK ] indication turns on.
Less than
Open lid
Close lid Buzzer offBuzzer on
Buzzer on and
abnormal alarm
Water drain
Unplug the power
cord from the
outlet and re-plug
it again after
5 seconds
10 sec.
More than
10 sec.
Water faucet
Water supply
hose cover
A
B
Screw (4)
Water tap
adaptor
Lever Approx. 4 mm
B
Adjustable leg knob
Adjustable leg
Loosen Tighten
To raise To lower

- 10 -
5. OPERATIONS PANEL
5.1 NA-F60A6 / NA-F70A6 / NA-F756A / NA-F70G6 / NA-F70G6P
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
Fuzzy logic control is used to recommend the proper water level and amount of detergent for the amount of laundry being done.
Caution : If you need to change the [ PROGRAM ] and [ SOAK ] settings after the cycle has already started, turn the power off and on it back.
RESERVE
• You can choose the finishing time to 9 hours.
SOAK
• Operations course for heavily washed laundry. • You can choose your soak time from 1, 3 or 8 hours. • You can adjust soak time based on the condition of dirt.
OFF/ON
• The power automatically turns off when total operations is finished. • The power automatically turns off if [START/ HOLD] button is not pressed within 10 min after turning on the power.
PROCESS
• Press to select WASH only, WASH and RINSE or other individual functions.
WATER LEVEL (Water Volume Display
• The appropriate WATER LEVEL for the size and type of your laundry will be displayed. • You can adjust the WATER LEVEL according to your desired level.
START/HOLD
• Press this to start. • Press this to stop in the middle of the cycle.
PROGRAM ( Course Select)
• According to type of laundry and stain, you can select suitable course yourself.

- 11 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
5.2 NA-F70X6 / NA-F806X
SOAK
• Operations course for heavily washed laundry. • You can choose your soak time from 1, 3, 5 or 8 hours. • You can adjust soak time based on the condition of dirt.
OFF/ON
• The power automatically turns off when total operations is finished. • The power automatically turns off if [ START/ HOLD ] button is not pressed within 10 min after turning on the power.
PROCESS
• Press to select WASH only, WASH and RINSE or other individual functions.
WATER LEVEL (Water Volume Display)
• The appropriate WATER LEVEL for the size and type of your alundry will be displayed. • You can adjust the WATER LEVEL according to your desired level.
START/HOLD
• Press this to start. • Press this to stop in the middle of the cycle.
PROGRAM (Course Select)
• According to type of laundry and stain, you can select suitable course yourself.
TIME DISPLAY
• When the machine is in operation, the time display shows how much time (in minutes) is left. • When the programmable timer has been set, this display shows how much time is left until the wash is finished by pressing the [ RESERVE ] button. • Timer indication on the panel will show longer timer than selected time as it includes water feeding, draining, etc.
RESERVE
• Press the [ RESERVE ] button to set how many hours later you would like the wash to be completed.
Fuzzy logic control is used to recommend the proper water level and amount of detergent for the amount of laundry being done.
Caution : If you need to change the [ PROGRAM ] and [ SOAK ] settings after the cycle has already started, turn the power off and on it back.

- 12 -
6. WIRING DIAGRAM
6.1 NA-F60A6 / NA-F70A6 / NA-F756A / NA-F70G6 / NA-F70G6P
6.2 NA-F70X6 / NA-F806X
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
M
BROWN
GREEN / YELLOW
BLUE
CAPACITOR
GREY
YELLOW
YELLOW
YELLOW
PURPLE
YELLOW
WHITE
WHITE
PURPLE
RED
RED
RED
BLUE
BLUE
BLUE
BLUE
PINK
BLUE
BROWN
MOTOR
WV-7BR00
ELECTRONIC
CONTROLLER
FEED
VALVE
MOTORIZED
DRAIN
VALE
SAFETY
SW.
PRESSURE
SENSOR
ELECTRONIC CONTROLLER
M
BROWN
GREEN / YELLOW
BLUE
CAPACITOR
GREY
YELLOW
YELLOW YELLOW
PURPLE
YELLOW
WHITE WHITE
PURPLE
RED
RED RED
BLUE
BLUE BLUE
BLUE
PINK
BLUE
BROWN
MOTOR
WV-7BS00
FEED
VALVE
MOTORIZED
DRAIN
VALE
SAFETY
SW.
PRESSURE
SENSOR
ELECTRONIC CONTROLLER
CAUTION : DIFFERENT COLOUR CONNECTION
CAUTION : DIFFERENT COLOUR CONNECTION

- 13 -
7. TABLE OF ERRORS
7.1 Case of buzzer alarm
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
• Is the hose connected?
• Is it clogged with lint?
• Is it crushed?
• Is the extension hose longer than 3m?
• Is the hose lay down?
• Is the tip soaked in water?
• Is a part of hose at a height of over 10cm midway?
After open
and close
of the lid.
Operation
will restart.
• Check if the lid is opened.
Close the lid.
Even it out.
• Is the laundry unbalanced?
• The machine is rattling. Is it inclined toward the floor?
• Is the adjustable knob loose?
(Adjust the machine, so it does not jiggle, then tighten the adjustable
knob)
• Check if you have forgotten to connect the water hose and to turn on
the faucet.
• Check if the connection of the water supply hose is clogged with dirt.
Please refer to “Maintenance” (Water supply hose filter)
• Check lif the water supply failure.
• Check if the lid open more than 10 seconds after start of water feeding.
• [CHILD LOCK] mode will activated to force the water drain.
• Pull out power plug from the socket outlet and replug it after 5 seconds.
• Please refer to “[CHILD LOCK]” program.
• The buzzer does not sound.
• Pull out the power plug and request for service.
RESERVE
(9 hours)
Flashing
Flashing
DELICATE
SPEEDY
NORMAL
CHILD LOCK
Check if abnormalities listed below are seen in the
external water hose.

- 14 -
7.2 Error Indication
If the following indications appear on the display panel (buzzer sounds, U and H characters appear).
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
Restart with
opening and
closing the
lid.
• Check if abnormalities listed below are seen in the external water hose.
• Is the hose connected?
• Is it clogged with lint?
• Is it crushed?
• Is the tip soaked in water?
• Is a part of hose at a height of over 10cm midway?
• Is the extension hose longer than 3m?
• Is the hose being used too small?
• Check if the lid is opened.
• Close the lid.
• Is the washing machine is an unsteady position, or is it on an inclined floor surface?
• Is the laundry unevenly distributed in the tub?
• Arrange the laundry evenly in the tub, then close the lid.
Restart with opening
and closing the lid.
• Check if you have forgotten to connect the water hose and
to turn on the faucet.
• Is the water supply cut off?
• Check if lid is open when draining operation of the [CHILD LOCK] program is ON.
• In case of H displays such as “H01”, with no buzzer sounds pull out the power plug, and
contact your dealer for service.

- 15 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
7.3 Setting after U11 happen
NA-F70X6 / NA-F806X
2
4 5
2
1
3
2
4 5
2
1
3
1. Set to power switch to “OFF”.
2. Press [PROCESS] + [PROGRAM] and POWER [OFF/ON] button 1 time.
3. Press [WATER LEVEL] button 3 times.
4. Press [SOAK] button 2 times (WATER LEVEL 6 mm. up).
Remark : Indication on LED from 3B to 39.
5. Press [START/HOLD] button 1 time.
1. Set to power switch to “OFF”.
2. Press [PROCESS] + [PROGRAM] and POWER [OFF/ON] button 1 time.
3. Press [WATER LEVEL] button 3 times.
4. Press [SOAK] button 2 times (WATER LEVEL 6 mm. up).
Remark : After change light will be indicate on WASH and TUB HYGIENE.
5. Press [START/HOLD] button 1 time.
Note : If water level is higher or lower, please adjust water level.
TAP SOAK PROCESS
1 3 mm. up 3 mm. down
2 6 mm. up 6 mm. down
3 9 mm. up 9 mm. down
4 12 mm. up 12 mm. down
RESERVE TIME LEFT CHILD LOCK
CHILD LOCK
TUB HYGIENENORMAL
SPEEDY
DELICATE
RESERVE
(9 hours)
TUB HYGIENE
BLANKETNORMAL
MINI
HYPER SPEEDY
DELICATE

- 16 -
8. TROUBLESHOOTING
8.1 Table of troubleshooting
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
Machine
does not work
Unusual
amount of
water inside
machine
Washing
system does
not work
Unusual
draining
Unusual
spinning
system
Unusual loud
noise
Water leak
Incorrect
working
Problem
(have to check)
Corresponding device
No light at the dial
Dial light is on
No sound of water from inlet valve
There is sound of water from inlet valve
Not enough water flow
Water never stops flowing in
Pulsator does not spin (no sound of motor)
Pulsator does not spin (there is sound of motor)
Pulsator spins only one way
Pulsator spins slowly
No draining
Drains slowly
No spinning (no soud of motor)
No spinning (Pulsator spins)
No force in spinning (tubspins slowly)
Loud noise during washing
Loud noise during dry spinning
Water leaks from drain pipe
Water leaks at the bottom of machine
Water is supplied during spinning
Rinses more than 3 times
Pulsator spins despite no water
Cannot change function program
Water does not flow out of a filter
No overflow during water filling as rinsing
Selected washing program cannot be memorized
Fabric softener flows away too fast
Pulsator spins in short range as washing and
rinsing
Works at low wash level then supplies water
again
Check water supply
Check water supply
Motor
Belt, Motor
Pulley Motor
Belt, Motor
Belt, Motor
Check installation
Something clogged
Drain pipe A,
Pulsator
Unbalanced tub,
leaning
Unbalanced tub,
leaning
Air pipe clogged
Description of
usage
Description of
usage
Description of
usage
Description of
usage
Description of
usage
Description of
usage
Description of
usage
0
0
0
0
0
0
0
0
0
0
0
Others
Control panel
Water Inlet Valve
Water level sensor
Safety switch Gear motor
Capacitor Mechanism case
Holding spring
Packing valve
0
0
00
0
0
0
0
0
00
0
0
0
00
0
0
0

- 17 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
8.2 The following symptoms are not trouble.
Symptoms
Machine begins filling water in
the middle of the wash.
Causes
• When the laundry amount is large at the HIGH water level, the
machine sometimes fills automatically. When level goes down, the
machine fills automatically.
The water level is too high for
the amount of laundry being
washed.
• When the laundry is already soaked with water before the wash is
started, or if there is water in the tub before the wash is started, the
water level will sometimes be higher.
The water level is too low for
the amount of laundry being
washed.
• With light laundry made of synthetic or blended fabric, the water level
will sometimes be lower.
Midway during spinning, the
operation suddenly changes to
rinsing.
• When the laundry is unbalanced during spin, rinsing and automatic
correction of unbalanced laundry will begin. Later spinning will return
to normal condition.
Water does not flow through
the lint filter. Double Cascade
does not operate.
• When the water level is set to very low, water sometimes will not flow
through the lint filter. Double Cascade does not operate when these
settings have been selected.
Softener spills out from softener
drawer.
•
•
Keep the level of the softener indicated to prevent the softener from
flowing immediately.
If you close the softener drawer forcefully, softener may spill out of
the drawer.
During draining, the laundry
and the spinner rotates with
irregular movements.
• To suppress soap suds build-up, the washing tub turns slowly and
quickly.
The buttons do not work.
• Only the [WATER LEVEL] button is available after the machine
begins washing.
• To change the setting, press the [START/HOLD] button or press the
[POWER OFF/ON] button and reconfigure the setting.
If you start with the rinse cycle,
the tub is not filled with water.
• When there is water in the tub, the operation starts with the draining.
After spin cycle is finished, the tub will be filled with water.
Washing machine does not
run at all.
• Check if there is power failure.
• Check if the power fuse has blown out or the breaker is actuated.
• Check if the power plug is plugged in thoroughly.
• Check if the “Power” switch has been pressed.
• Has the water faucet been turned on?
• Check if the [START/HOLD] button has been pressed.
• Has the machine been programmed under [RESERVE] timer?

- 18 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
Symptoms
Machine begins filling water in
the middle of the wash.
Causes
• When the laundry amount is large at the HIGH water level, the
machine sometimes fills automatically. When level goes down, the
machine fills automatically.
Water is not supplied.
• Check if the water faucet is turned on.
• Is the water supply cut off?
• Check if the connection of the water supply hose is clogged with dirt.
• Check if the lid is opened. Close the lid.
Washing operation still continue
even though the expected
finishing time had passed on
Reserve Program.
• Washing time will be longer because of laundry unbalance, water
feeding and draining condition.
Buzzer sounds followed by a
draining when opening the lid
during wash and rinse.
• In the case when open the lid after setting the [CHILD LOCK] mode,
it will force the draining process. Pull out power plug from the outlet
and replug it after 5 seconds.
Tub shaking with the sound
of water.
• This is the sound of the liquid to maintain the balance during spinning.
Water supply failure.
• Normally after the water supply failure, the water will become muddy.
Detach the water feeding hose and turn on the water faucet to release
to due muddy water. Fix water hose and start washing.

- 19 -
9. PARTS EXPLODED VIEW AND REPLACEMENT PARTS LIST
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
9.1 Parts Exploded View - A
A4
3
3
2
A16
A11
A12
A14
A10
A17
A3
A6
A7
A15 A20
A13
A8
A9
A9
Model NA-F70X6 / NA-F806X
A19
A2
A1
A2

- 20 -
NA-F60A6, F70A6, F756A, F70G6, F70G6P, F70X6, F806X
9.2.1 Replacement Part List : A for NA-F60A6
Important safety notice :
Screws
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacturer’s specified part.
REF.
NO.
SIN
(LOCAL)
UAE
(ONE)
UAE
(PGF)
SIN
(EXP)
1
2
3
4
PART NAME PART NO. SAFETY TH MAL IND OMAN KUWAIT QATAR PHIL
222 2
5 5 5 5 5
2 2 2 2 2 2 2
55 5 5 5 5
222 2 2 2 2 2 2 2 2
222 2 2 2 2 2 2 2 2
222 2 2 2 2 2 2 2 2
222 2 2 2 2 2 2 2 2
222 2 2 2 2 2 2 2 2
SPECIAL TAPPING SCREW XTWAXW469J
BINDING TAPPING SCREW
BINDING TAPPING SCREW
BINDING TAPPING SCREW
BINDING TAPPING SCREW
BINDING TAPPING SCREW
BINDING TAPPING SCREW
XTB4+12CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
XTB4+15CFJ
5
6
7
Parts List
REF.
NO.
SIN
(LOCAL)
UAE
(ONE)
UAE
(PGF)
SIN
(EXP)
A1
A2
PART NAME PART NO. SAFETY
S
S
S
S
TH MAL IND OMAN KUWAIT QATAR PHIL
1
1 (EXC.)
1 (EXC.)
1 (EXC.)
1 1 1
1
1
1 1
1
1
1 (EXC.) 1 (EXC.) 1 (EXC.)
1 (EXC.) 1 (EXC.) 1 (EXC.)
1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.)
1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.)
1 1 1 1 1
1 1 1 1 1
1 1
1 1
1 (EXC.) 1 (EXC.)
1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.) 1 (EXC.)
1 (EXC.) 1 (EXC.)
444444 44444
11 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1
1 1 1
PANEL A (GREY) AXW01307BR0J
PANEL A (WHITE) AXW01307BR0D
PANEL FACE B AXW01467BU0J
A3 BODY B (GREY) AXW01027BR0J
BODY B (WHITE) AXW01027BR0D
A4 LID UNIT AXW001G7BU0J
A5 LID PACKING A AXW01646UP00
A6 LEVELLER AXW03536DKA0
A7 SPINNER LID LABEL AXW11177BS5D
A8 FEEDING PORT PACKING AXW02676UP00
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
11 1 1 1 1 1 1 1 1 1
A11 FEEDING VALVE AXW292119706
SA12 PRESSURE SENSOR U AXW024T03200
A13 LID HINGE SHAFT AXW01937BK00
A14 SUB DRAIN HOSE UNIT AXW002Q6UP00
A15 DETERGENT CASE UNIT AXW021B7BR00
A16 SAFETY SWITCH AXW166123400
A17 LID HINGE SPRING AXW11167BR00
A18 CONTROLLER CASE LID AXW24277BR00
A20 PANEL FACE C AXW01477BS00
AXW166122910
S
S
S
AXW024T02900
11 1 1 1 1 1 1 1 1 1A10 CONNECTOR LEAD
WIRE UNIT
AXW014A7BR00
A9 CONTROLLER UNIT AXW024C7BU06
AXW11177BS50
AXW11177BSKA
AXW001G7BU0D
AXW01467BU5A