Panasonic NA-FS90X1 User manual

Fully Automatic Washing Machine
Operating Instructions
Thank you very much for purchasing Panasonic Product.
Before operating this washing machine, please read these instructions completely, paying
special attentions to Safety & General Precautions.
W9901-7JP50
PHAT0909-0
Printed in Thailand
Model No.
NA-FS90X1_80X1_EN-ML.indd 1NA-FS90X1_80X1_EN-ML.indd 1 9/11/09 4:33:23 PM9/11/09 4:33:23 PM

5
Procedures before washing
• Check the installation
See pages 21~23 for details.
1 Level the washing machine by adjusting the
adjustable leg and using the leveller as reference.
2 Connect the water supply hose.
3 Turn on the faucet.
4 Plug power cord into socket outlet.
5 Insert the drain hose to drain.
[NOTE]
Before installation, please make sure to install the
bottom cover. See page 23 for details.





Accessories
Water Supply Hose (1)
Length: 1.0 m
Bottom Cover (1)
Water Tap Adaptor (1)
Note: Water Tap Adaptor
is set to the Water
Supply Hose.
Drain Hose (1)
Screw (2)
Note: For Bottom Cover
Detergent /
Bleach Inlet
Lint Filter
(2 places)
Leveller
Feeding Valve
Lid
Power Plug
Adjustable Leg
Drain Hose
Inner Lid
Softener Drawer
Lid Lock Part
Pulsator
Operation
Panel
Tub
• Do not bundle
the power cord
when it is used.
• For safety reason, the lid is locked after the operation starts.
• For putting in/taking out the laundry, if the “Start/Pause” button is pressed, the lid can be opened even
when the Air Dry operation is being performed.
* Do not unplug the power cord. (The lock cannot be cancelled.)
The lid does not
open when this
indicator is lit.
After
starting
The operation can be resumed.
When the tub stops rotating
(after about 15 seconds), the
lock is cancelled with a click.
NOTE
• Do not force open the lid if it is locked. (Damage to the lid may result.)
A buzzer sounds if the user attempts to force open the lid.
• If the “Child Lock” indicator is lit, cancel the Child Lock mode (page 17).
• If the lid is not locked during operation, stop using the washing machine immediately and contact your dealer
for repair.
Lid Lock while operating
Do not put any object such
as detergent, softener, button
and coin into the depressed
part. (A failure may result.)
Name of parts
NA-FS90X1_80X1_EN-ML.indd 5NA-FS90X1_80X1_EN-ML.indd 5 9/11/09 4:33:28 PM9/11/09 4:33:28 PM

ลบเส้นออกเหมือนรูปหน้าปก

22
A
B
Connect the water supply hose
That the appliance is to be connected to the water faucet using new water tap adaptor and water supply hose
and that old one should not be reused.
1. Loosen the 4 screws on the water tap adaptor just enough to slip the adaptor over the mouth of the faucet.
2. Slip the water tap adaptor over the faucet, keeping it in a straight line with the faucet. Tighten the screws,
applying even pressure all around. When the space behind washing machine is narrow due to a wall or
other obstacle, adjust the back screw to the proper position before slipping the connector over the faucet.
3. Remove the tape and tighten B by turning it to the right.
4. With the water supply hose cover and lever pushed down, slide the hose up onto the proper position release
them before hear it click into place.
5. Pull down on the hose to make sure it will not come off.
6. Turn on the water faucet to check for leaks.
[Note]
• Firmly tighten part B of the water tap adaptor,
otherwise water leakage will result.
• If a water tap adaptor is already connected,
replace with the attached new one.
• When the hose must be reinstalled (after you
remove, for example), turn B to the left until
about 4 mm of the thread becomes visible, then
carry out the procedure described above.
Screws (4)
Water tap
adaptor
Lever
Water faucet
Water supply
hose cover
Approx. 4 mm
Connect the water supply hose to the
water supply valve screw.
1. Push the water supply hose nut straights onto
the water supply valve screw.
2.
Hold the elbow by lifting it up, screw the nut onto the
water supply valve screw, and firmly tighten the nut.
3. After the nut is tightened, check whether or not
the elbow is unsteady or loose.
4. After tightening, open the faucet to confirm that
there is no water leakage.
[Cautions]
• Firmly tighten the nut, otherwise water leakage
will result.
• Water Pressure Rating :
0.03 MPa - 1 MPa
Water
Supply Hose
Drain hose
Hose extension
If extended external part is necessary when connecting the drain hose, the length of the drain hose should
be less than 3 m and the height should be below 10 cm. Do not put hose tip under the
water
Over 10 cm
Below 10 cm.
3 m max.
Good Example
Install the machine 10 cm or more away from the wall.
B
Elbow
Nut
Water supply valve screw
NA-FS90X1_80X1_EN-ML.indd 22NA-FS90X1_80X1_EN-ML.indd 22 9/11/09 4:33:45 PM9/11/09 4:33:45 PM
ลบเส้นออกเหมือนรูปหน้าปก

Error Indication
Check the followings if a buzzer sounds and “U” and “numeral” are displayed alternately. (Cancel the
Child Lock mode if it is set (page 17).)
Specification
Model NA-FS90X1 NA-FS80X1
Voltage 220-240 V~ 220-240 V~
50 Hz 50 Hz
Power consumption 310 W 300 W
Standard water amount 66 L 62 L
Maximum capacity 9.0 kg8.0 kg
Length of power cord (Approx. 1.6 m)
W x L x H 559 x 626 x 1026 (mm)
Net weight 41 kg41 kg
U11
Cannot drain water
nCheck if any of the following is observed
on the drain hose.
• Is the hose put down?
• Is the hose clogged with lint?
• Is the hose crushed?
• Is the tip of the hose put in water?
• Is the middle of the hose raised more
than 10 cm?
• Is the extension hose longer than 3 m?
• Is the hose used too small?
• Is the hose frozen?
• Is lint accumulated in the drain port?
Operation
resumes by
opening and
closing the lid.
U12
The lid is open
• Is the lid open? éClose the lid.
• Is any object such as button and coin stuck at the lid lock part?
éRemove the object (page 5).
U13
Cannot spin
Cannot dry
• Is the load unevenly distributed? éRedistribute the load evenly
and close the lid.
• Is the washing machine unstable or placed on an inclined floor?
éOperation resumes by opening and closing the lid.
U14
Cannot supply water
• Is the faucet turned on?
• Is the water tap or water supply hose frozen?
• Is there a water disruption?
• Is the water supply hose filter clogged?
(page 19)
Operation
resumes by
opening and
closing the lid.
* If the error still persists even after checking the above or in the event any error other than the above
occurs, disconnect the power plug and inform your dealer of the error indication displayed.
H • If “H” and “numeral” are displayed alternately, inspection is
required. Disconnect the power plug and inform your dealer of
the error indication displayed (2-digit numeral following “H”).
Lit
Unbalance
NA-FS90X1_80X1_EN-ML.indd 26NA-FS90X1_80X1_EN-ML.indd 26 9/11/09 4:33:47 PM9/11/09 4:33:47 PM
60
310 W
ทําเป็น2ช่อง Ex. 230 V~ 220-240 V~
60 Hz 50 Hz
310 W 310 W
230 V~