Panasonic NA-FS95G2 Product guide

Model No. NA-FS95G2
Contents
Safety Precautions 2
Part Names 3
Operation Panel 4
Variety of Programs 5
Detergent 6
Washing 7
Washing Options 8
• Bedding
• Delicate
• Cotton Eco
• Air Dry
(90 min)
• Wash / Rinse / Spin
Convenient Functions 10
Maintenance 10
Installation 12
Troubleshooting 15
Error Display 16
Specifications 16
Thank you for purchasing this product.
- Read these instructions carefully for optimum
performance and safety before use.
- Keep this manual for future reference.
Operating & Installation
Instructions
Fully Automatic Washing Machine
(Household Use)
AWW9901D4M01
T1019-11219 (A)(N)
Printed in Thailand
12-2019

2
snoituacerPytefaS
Home hot water heater safety
●Under certain conditions, hydrogen gas may be
produced in your hot water heater that has not been
used for two weeks or more. Hydrogen gas can be
explosive under these circumstances. To prevent
the possibility of damage or injury, you should turn
on all hot water faucets in your home, and let the
water flow out for several minutes before connecting
to your washing machine. This will allow any built-
up hydrogen gas to escape. Since hydrogen gas is
flammable, do not smoke or use an open flame or
start appliance during this process.
Never do the following about the
power plug and cord
(To prevent fire or electric shock)
●Do not plug in or unplug the power cord with wet
hands.
●Do not hold or pull on the cord when removing the
plug from the socket.
●Do not use a power cord or plug that is damaged.
If the power cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Observe the following about the
power plug and cord
(To prevent fire or electric shock)
●Use a socket that satisfies the rating requirement
solely for this appliance. Do not use a plug adaptor
or extension cord.
●Always fully insert the power plug into the socket.
●Wipe the power plug periodically with a dry cloth.
(Accumulated dust collects moisture, which may
cause insulation failure, resulting in fire.)
●Unplug the power cord before cleaning.
Never disassemble, repair or modify
the appliance yourself.
●In case of malfunction or failure, immediately stop
use, unplug the power cord, and ask your nearest
service centre for repair.
Do not allow children to use on their
own.
●This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
●Children should be supervised to ensure that they
do not play with the appliance.
.erifmorfyawapeeK
roslairetamelbammalftuptonoD
clothes with such things attached in
the tub. Keep them away from the
appliance.
(To prevent explosion or fire)
●For example: Kerosene, gasoline, benzine/thinner,
alcohol, etc.
Do not touch the tub until it
completely stops.
(To prevent injury)
●If the tub does not stop within 15 seconds when
the lid is opened during spin process, switch off the
appliance immediately and call a service person.
Be sure to provide a ground.
(To prevent electric shock if electricity leakage occurs.)
●To establish a ground, ask a service person to do
the grounding work.
May cause serious injury or death.
WARNING
Read and follow these safety precautions.

●Water supply hose (2)
• Length: 1.5 m
●Drain hose (1)
●Hose band (1)
●Hose holder (1)
●Screw (1)
●Bottom cover (1)
●Screw (1)
Safety Precautions Part Names
3
semaNtraP
Do not wash, rinse, or spin
waterproof sheets or clothes.
(To prevent injury, damage to the main unit, walls, floor
or laundry, or water leakage if the appliance falls over
or oscillates extremely while spinning)
●Raincoats, wet suits, etc.
Observe the following
●Locate away from direct sunlight or heat.
(To prevent malfunction or deformation.)
●New hose-sets supplied with the appliance are to be
used and old hose-sets should not be reused.
●Be careful not to get your flngers caught when
opening and closing the lid.
●Do not insert your hands or feet under the main unit.
(To prevent injury by rotating parts.)
●Do not climb or put heavy objects on the appliance.
(To prevent deformation and breakage resulting in
injury)
●If the lid is broken, immediately stop using the
appliance.
(To prevent deformation and breakage resulting in
injury)
●Do not use water hotter than 60 ºC.
●Do not make wrong connection for the HOT and
COLD water supply faucets.
●Depending on the connected water heater, very hot
water may come out. Be careful not to burn yourself.
●Do not add extra water directly into the tub.
●Do not obstruct the openings of the bottom face with
carpet, etc.
Turn off the water faucet after operation.
(To prevent water leakage)
CAUTION
For machine-washable items only.
This appliance is intended to be used in household.
This appliance is not intended to be used in
applications such as:
- staff kitchen areas in shops, offices and other
working environments;
- farm houses;
- by clients in hotels, motels and other residential
type environments;
- bed and breakfast type environments;
- areas for communal use in blocks of flats or in
launderettes.
For maximum mass of dry cloth and pressure of tap
water, see P.16 .
May cause injury or property damage.
Drain hose
(P. 13)
Pulsator
retliftniL
(P. 10)
Lid
Tub
Operation
panel (P. 4)
Leveller
(P. 14)
Softener
case
(P. 6)
Power cord
and plug
(P. 14)
Detergent
inlet
(P. 6)
Adjustable leg
(P. 14)
●COLD
●HOT
Water supply valve (P. 14)
Accessories

4
QuickWash
Bedding
Operation Panel
Power Off/OnAir Dry (P. 9) Start/Pause Program selection (P. 5)
Child Lock lamp (P. 10)
Change water
amount
During the wash
process, press “Water
Level” to change the
water amount.
●Some water amounts
cannot be selected
depending on the
program.
●Only during the wash
process, press “Water
Level” to check the
water amount.
Water level/water amounts
Level High
10-8
Mid
7-5
Low
4-2
Extra
Low
1
Detergent *
Water amount (L) 99 88 81 74 66 59 52 46 38 33
* : 1 scoop of detergent
●Each water level, except “Extra Low”, has
three water amount options that can be
switched while the level is lit by pressing
“Water Level”.
Water amount/remaining time
After starting operation, indicates
the water amount according to the
amount of laundry.
After approx. 5 seconds, indicates the
approximate remaining time (min).
ECONAVI lamp (P. 8)
NOTE
●In case of a power failure during operation, operation will resume from the point where it was stopped when the
power is recovered (Auto Restart).
●The power turns off automatically if you do not press “Start/Pause” within 10 minutes after power-on.
■Touch operation
●Operation buttons are capacitive (Except for the power Off/On and Start/Pause buttons). Touch the buttons
directly with your bare fingers.
●When a towel containing water or detergent touches an operation button, the appliance may malfunction.
Change process
settings
Change the combination
of wash, rinse and spin
processes, and the time
length or number of times
for individual processes.
(P. 9)
Flashing (in progress)
Lighted
●After starting operation,
you can change settings
only during wash
process by pressing
“Start/Pause”.
Preset
Set the time to finish washing
(in hours). ( lights.)
e.g.) 8 hours later
●Setting range: 2 - 24
hours later, in one-hour
increments. (3 - 24 hours
later for the Cotton Eco
and Soak programs)
●Not available for the
following programs:
Delicate , Fragrance,
Bedding, Tub Hygiene,
Air Dry
Temp Setting
For washing, cold water can be mixed
with hot water. Press the button to select
Hot/Warm/Cold. (P. 7)
Do not use water hotter than 60 ºC.
● The estimated water temperature in
the tub during wash process (when
hot water is 50 ºC, and normal water
is 20 ºC):
Hot approx. 40 ºC
Warm approx. 30 ºC
● Lamp indications
Lighted: Hot/Warm/Cold is set.
Flashing: Hot water is being supplied.

Operation Panel Variety of Programs
5
Variety of Programs
Laundry preparation and check
For clothes losing colour easily
Wash separately.
Pre-laundry check
To prevent damage to clothes,
malfunction and drainage failure
●Remove coins, pins, paper clips, nails,
etc.
●Fasten buttons and close zippers.
●Do not wash items (such as paper
diapers) other than laundry.
●Reverse clothes likely to pill.
●Use a brush to remove pet and
human hair, sand, etc.
●Tie strings, etc.
●Remove any knots in clothing and any
tangles.
For delicate underwear only
Use laundry nets.
●Underwire brassieres
●Lacy clothes, lingerie and stockings
When using a net
●Do not overpack.
●Put the zipper's slider into the cover.
(To prevent damage to clothes and
the main unit)
●Do not use the Air Dry program.
(To prevent uneven drying and
wrinkles)
Purpose Program Maximum
capacity
Everyday
clothes Daily washing Cotton (P. 7) 9.5 kg
Speedy washing for light soil Quick Wash (P. 7) 9.5 kg
Delicates Washing
delicates gently Delicate (P. 8) 5.0 kg
Using extra
softener Stronger scent Fragrance (P. 7) 9.5 kg
Saving washing water and energy
* Washing consumes less energy and water, but
takes longer.
Cotton Eco (P. 8) 9.5 kg
Heavily soiled
clothes
Presoaking to wash
Soak (P. 7) 9.5 kg
Blankets Bedding (P. 8) 4.2 kg
Drying synthetic fibre clothes Air Dry (90 min)
(P. 9)
3.0 kg
Tub drying
Preventing black
mould and smell
Air Dry (90 min)
(P. 11)
―
Tub cleaning Tub Hygiene
(P. 11)
―

6
Detergent
Putting in detergent
Do not put detergent directly into the tub.
Detergent may remain undissolved.
●The level of foaming depends on condition such
as load size, degree of soiling, detergent type, and
water hardness.
Putting in bleach
●Do not use whiten bleach (chlorine bleach) for
coloured clothes to prevent loss of colour.
●Do not use bleach for the Delicate program.
Putting in softener
●Softener is automatically released during the final
rinse process.
●To add softener during operation, press “Pause”
first.
●Up to about 160 ml can be added. To add more
softener, use the Fragrance program.
●When using
concentrated softener,
dilute it with water before
putting it in.
NOTE
●Do not use separated or solidified softener.
●Softener cannot be used with the Cotton Eco
program.
Concentrated
softener Water
Put in detergent, bleach and
softener according to the water
amount displayed.
●Follow the instructions on each package.
●Turn the tub by hand if it is difficult to put in the
detergent inlet. (P. 10)
●Attach the detergent inlet cover if it comes off.
■Detergent inlet
Detergent/Bleach
■Softener case
Softener
●If the detergent/bleach inlet cover is wet, wipe
it before use. (Wet cover can cause detergent
clumps)

WashingDetergent
7
Washing Preparation:
●Check if the washing machine is properly installed. (P. 12)
●Turn on the water faucet.
●When using Temp Setting, turn on both hot and cold water faucets.
1After loading laundry
Turn the power on.
●The Cotton program is selected when the
power is turned on.
2Select a program. (P. 5)
■Temp Setting
■Timer preset
3Start.
The pulsator moves without
water and measures the
amount of laundry
(approx. 10 seconds).
Water amount indication
(approx. 5 seconds)
Remaining time indication
●To check the water amount
→Press “Water Level”.
4According to the water amount indication
Put in detergent.
●Approx. 20 seconds after the water amount
is displayed, water supply begins.
5Close the lid.
Operation ends with beeps.
Set how many hours later to finish
operation. (P. 4)
●2 minutes after start-up, all indications except
turn off.
●To confirm after the timer has been set, press
.
●To cancel or change, press .
●The hours that can be set differ depending on
the program.
When the Fragrance program is selected
The buzzer sounds before the final rinse and
operation is paused. Put the desired amount
of softener which has been diluted with water
directly into the tub.
5 beeps
●The Fragrance program cannot be selected
when Child Lock (P. 10) is set.
●Operation will resume if the lid is left closed for
more than 1 hour.
■After pressing “Start”
●You can change the water level until the end of
the wash process.
●You can change each of the “Wash”, “Rinse”
and “Spin” operation contents until the end of
the wash process. Press “Pause” beforehand.
●You cannot change the program.
Press to select Hot/Warm/Cold for
washing. (P. 4)
Hot ←Warm ←Cold
QuickWash
Bedding
23
Timer preset
Temp setting
1

8
Washing Options
IVANOCE
Available in the Cotton program, this function
automatically adjusts the operation time and water
amount according to the detected amount of
laundry and water temperature.
ECONAVI will not work if you change the water
amount or process settings.
■Lamp indications
●Flashing: Detecting
●Lighting: ECONAVI enabled
●Off: ECONAVI disabled
■Switch on/off
1
2
3Press and hold for 3 seconds
4to select (On) or (Off)
56 beeps
* Test conditions:
●Cotton program
●Comparison between ECONAVI-enabled operation (amount
of laundry: 2.0 kg, water temperature: above 35 ºC) and
ECONAVI-disabled operation (amount of laundry: 9.5 kg
(rated capacity), water temperature: below 15 ºC)
●Test was conducted based on IEC60456 except for water
temperature.
Bedding
■Washable blankets
●Material : 100 % synthetic fibre
or 100 % cotton
●Weight : 4.2 kg or less
(King size bed)
●Blankets with a machine-
washable tag attached
NOTE
●Use liquid detergent.
●The water amount indication shows the maximum
and cannot be changed.
Delicate
Use this program to gently wash delicate
clothes and stylish garments.
■Load laundry evenly
●Load lighter items first and press
them from above.
●Use laundry nets for delicate
underwear only.
●Amount that can be washed at
one time:
Water Level Capacity
74 L 5.0 kg
66 L 3.0 kg
59 L 1.0 kg
Cotton Eco
NOTE
●Do not use bleach.
●Use liquid delicate detergent.
●After operation ends, take out clothes immediately.
(To prevent wrinkles and colour staining)
With the “Cotton Eco” cycle the washing
machine consumes less energy and water.
Preparation :
Turn on both hot and cold water faucets.
(Default setting: Hot)
■About Detergent
●We recommend using high efficiency or low-sudsing
detergent.
●For better performance, it is recommended to
dissolve detergent in 1L of water at 35 °C and
then pour it around the inner wall of the tub.
●Add detergent after the hot water fill is completed.
Opening the lid to add detergent before hot water
filling is completed will alter the total amount of
hot water added, and hence washing performance
will change.
■Water amount can be adjusted according to
the table below:
Water Level Capacity
59 L 9.5 kg
52 L 6.0 kg
46 L 3.4 kg
NOTE
●Do not use softener
.
●The operation starts with the end of hot water filled.
●If “U13” appears, clothes in the tub are out of
balance. Follow installation (P.16) to distribute the
clothes evenly, and close the lid.
●We recommend leaving the washing machine for at
least 1 hour between each use.
●Cotton Eco is for normally soiled cotton load with
AS/NZS 2040.1, AS/NZS 2040.2 and AS/NZS 6400.

Washing Options
9
Wash / Rinse / Spin
Preparation: Turn on the water faucet.
1After loading laundry
Turn the power on.
2According to your purpose
Change process
settings.
●Change the water amount
as necessary.
3Select water
temperature.
4After closing the lid
Start.
Operation ends with
beeps.
Air Dry (90 min)
Water is removed from clothes by the air
blown from the tub rotation.
■Clothes that can be dried
• Material: Synthetic fibre
• Weight: 3.0 kgor less
1After loading clothes and closing the lid
Turn the power on.
2Press.
3Start.
After 90 minutes, drying
ends with beeps.
NOTE
●Clothes may not be sufficiently dried depending on
the amount and type of clothes, the temperature, and
the installation condition of the washing machine.
●Since no heater is used for this function, you may
feel that clothes are cold and half dry.
Contents of Programs
Program Total time
(approx.) Wash Rinse Spin Temp Setting Water level4)
Cotton 60 min 12 min
Hot
Warm
Cold
High
Mid
Low
Extra Low
Quick Wash 55 min 9 min
9 min
Fragrance 85 min 12 min
Soak 120 min
1) 12 min2)
Bedding 80 min 12 min High
Delicate 55 min Cold Mid
Cotton Eco 150 min
1) 12 min2) 7 min3) Hot / Cold Mid / Low
Tub Hygiene 150 min
1) 12 min2) 7 min Cold High
2) Although the time indication is “12 min”, soaking is
done before that. Approximate soaking time :
- Cotton Eco : 59 min
- Soak and Tub Hygiene : 60 min
3) Although the time indication is “7 min”, actual
spinning time may take up to 25 min.
4) Water Level depends on loading capacity.
5 min2 times
5 min2 times
5 min2 times
5 min2 times
3 min2 times
1 min2 times
3 times
2 times
NOTE
●Total time is approximate.
(When the standard water supply rate is
15 L / min)
●Total time may increase depending on low water
pressure, bad draining conditions, and the amount
and type of clothes.
1)
Remaining time of 99 minutes or less will be displayed.

10
Maintenance Convenient Functions
Cancelling end buzzer and
button operation sound
1Pressing down,
press.
Then hold on for
3 seconds. 2 short
beeps
●To reset, do the same procedure.
4 short
beeps
Setting Child Lock
To prevent children from falling into the tub and
drowning, if the lid is opened while the washing
machine is operating, this function sounds a buzzer
until it is closed. Not closing it within 10 seconds
flushes the water out.
●This function does not lock the lid and button
operations.
●When water is drained forcibly, “U 99” is displayed. (P. 16)
1After closing the lid
Turn the power on.
2Press and hold for
5 seconds. 2 short
beeps
●To cancel, do the same procedure. 4 short
beeps
Turning the tub by hand
If it is difficult to reach the detergent inlet.
1Turn the power on.
2When a clicking sound is heard
Turn the tub
within 20
seconds.
(Clockwise only)
NOTE
●If there is water in the tub, the tub cannot be turned.
Lint filter
After each operation
Lint filter
1Remove the
filter gently.
2Open the filter
and remove
lint.
●If lint is difficult to
remove, soak and
wash the filter in
water.
3Attach the filter in its original
position.
1 2
3 4 Click
NOTE
●Do not wash laundry without the filter.
(To prevent damage to clothes)
●Turn the tub by hand if it is difficult to remove the
filter.
●If the filter is broken, purchase a new one at your
local dealer.

Convenient Functions Maintenance
11
Water supply filter
If water does not flow smoothly
●Follow the procedure below to prevent
splashing of water.
1After turning off both hot and
cold water faucets
Turn the
power on.
2Select Hot or Warm.
3Start.
4After approx. 40 seconds
Turn the power off.
5Loosen the nut and remove
the hose.
6Remove the filter and remove
dirt on the filter.
Water supply filter
7Reattach the filter to this
original position.
Main unit, lid
If stained with detergent or softener
Wipe with a soft cloth.
(To prevent damage to resin parts or metal corrosion)
●For heavy soil, wipe with a neutral kitchen detergent.
●Do not splash water.
Tub
Once a week <Air Dry>
1After operation ends
Run the Air Dry program without
loading laundry.
(P. 9)
Once a month <Tub Hygiene>
Preparation: Turn on both hot and cold water faucets.
1Without loading laundry
Turn the power on.
2Press.
3Start.
When the tub is filled with water
Pause.
4Put bleach in the tub.
●Use whiten bleach
(drum cleaning detergent
commercially available).
Approx. 200 ml
5After closing the lid
Start.
After approx. 2 hours
and a half, tub cleaning
ends.
Softener case
Wash with water.
■How to remove
After pulling the case
all the way out, pull it
obliquely upward to
remove it.

12
Installation
1. Check the location.
■Avoid the following locations for installation.
• Damp locations or locations where it may be exposed to rain, etc. (To prevent electric shock or fire)
• Uneven or unstable locations (on blocks, timbers, a table with wheels,
etc.)
• Locations with a possibility of freezing
■Keep the washing machine at least 10 cm away from the wall to
minimise noise.
2. Attach the bottom cover.
1Insert the bottom cover along the guides. 2Fix with a screw.
Screw
B
A
Water supply
hose
Bottom cover Drain hose
Elbow
Holes for the
hose holder
Water supply
valve screw
COLD
HOT
COLD HOT
Water supply
hose

Installation
13
1Connect.
Insert all the way.
2Slide the hose band in the arrow direction.
●Slide all the way until it stops.
Hose band
3Attach the hose to position A
or B with the hose holder and
the screw.
A
B
Hose holder
Screw
4
Make sure the drain hose is securely hooked
so that it does not come off by water pressure
during drainage.
NOTE
●Do not twist, pull out or bend the drain hose.
●Do not put the hose tip under water.
●Do not direct the drain hose downwards.
●The installation shall be in accordance with the requirements
of AS/NZS 3500.1.
● End of drain hose is not lower than high water level in the tub.
CAUTION
Hook the elbow of the drain
hose to the basin.
80 - 120 cm
3. Attach the drain hose.
■Make sure to ask a service person for installation. Do not install by yourself.
■If the installation, test run and inspection of the washing machine are not carried out following this installation
method, Panasonic will not be liable for any accident or damage caused.
Do not connect here.

14
Installation (continued)
4. Connect the water supply hose.
1
1Hold the elbow and tighten the nut.
2Check that the elbow is not loose.
●The procedure for cold water
and hot water is the same.
2
3Turn on the water faucets
slowly and make sure there
are no leaks.
●Do not make wrong
connection for the HOT
and COLD water supply
faucets.
●Tighten the nut firmly.
●Do not twist, squash, modify
or cut the hose.
●
●Time for hot water to reach washing machine will depend on proximity of washing machine to hot water tank.
Elbow
Connect the water
supply hose to the water
supply valve screw.
Connect the water supply
hose to the water faucet,
and tighten the nut
clockwise with your hand.
.
Water faucet
Water supply hose
Water supply
valve screw
Nut
Water supply
hose
COLD HOT
CAUTION
NOTE
If you have an uncontrolled water heating source (e.g., wet back, solar heating),
fit a tempering device (e.g., a safe valve). This will ensure the hot water temperature remains within safe limits.
Contact a local plumber or plumbing supply merchant for the most suitable type of tempering device.
5. Connect the power plug and grounding wire.
●Plug the power cord into a dedicated household 3-pin AC outlet rated at 10 A, 220 V to 240 V.
If you are not sure, contact a qualified electrician.
6. Check that the washing machine is level.
The bubble should be at
the centre of the mark.
Leveller
Mark
Bubble
■If the bubble is out of the mark
3Turn to the right to
tighten.
1Turn the adjustable leg knob to
the left to loosen.
2Turn the adjustable
leg to eliminate
wobble.
To lower
To raise
7. Perform a trial operation.
●Check that there is no water leakage, abnormal sounds or error display.

Installation Troubleshooting
15
Troubleshooting
Symptoms Points to be checked
Time
Time indication increases
or does not decrease.
●Time indication is approximate. Remaining time is corrected during
operation and displayed.
Operation time is longer
than the time indication.
Operation does not stop
even after the preset time.
●The operation time may be longer if laundry is concentrated on one
side or the water supply or drainage is not good.
(P. 16 “U 11” “U 14”)
Main unit
No operation
●Power failure?
●Is the lid closed completely?
●Has the power fuse blown or the breaker tripped?
●Is the power plug inserted completely?
●Is the water faucet turned on?
●Did you press “Start”?
●Is the timer preset?
Cannot change process
settings (after start-up).
●Process settings can be changed during wash process by pressing
“Pause”. To change the program or settings after the end of wash
process, turn the power off and on again.
Wash
No water supply
●Is the water faucet turned on?
●Water outage?
●Is the water supply filter clogged with dirt? (P. 11)
Water is supplied in the
middle of wash process.
●If the water level drops, water is added automatically.
●With a large amount of laundry, water is added several times
automatically.
The water level is too
high for the amount of
laundry.
●If laundry is wet or there is water in the tub before operation, the
water level may be higher.
The water level is too low
for the amount of laundry.
●With light clothes (of synthetic fibre, etc.), the water level may be
lower.
Rinse/Spin
Operation started with
rinse, but water is not
supplied.
●If there is no water in the tub, water is supplied after spin.
●If there is water in the tub, water is supplied after water discharge.
Operation suddenly
changes to rinse process
in the middle of spin.
Only spin is desired, but
operation starts with
rinse.
●If clothes are concentrated on one side of the tub, the washing
machine automatically corrects unevenness by starting rinse
process.
(Place clothes as evenly as possible.)
Irregular rotation during
spin ●The tub rotation speed is adjusted to reduce foaming during spin.
Others
Power failure/
The breaker has tripped.
●Operation will resume from the point where it was stopped when the
power is recovered (Auto Restart).
Water outage
●When water supply is recovered, remove the water supply hose,
release turbid water from the faucet, and then start the washing
machine.
Cannot select the
Fragrance program.
●If Child Lock (P. 10) is set, the Fragrance program cannot be
selected.
There is noise when
water drains out. ●This is normal. It is the noise of the drain pump working.

16
Panasonic Customer Care Centre
Specifications
NA-FS95G2
Rated voltage 220 - 240 V
Rated frequency 50 Hz
Rated power consumption 590 W
Standard water amount 99 L
9.5 kg
Product dimensions 643 mm (W) x 709 mm (D) x 1074 mm (H)
Product weight 49 kg
Pressure of tap water 0.01 - 1 MPa
Maximum mass of dry cloth
http://www.panasonic.com
© Panasonic Appliances (Thailand) Co., Ltd. 2019
●The buzzer sounds and “U”/“H” and a number are alternately displayed.
●Cancel Child Lock (P. 10) if it is set.
Error Display
Error display Points to be checked
Water cannot drain.
Check the drain hose for the following abnormalities:
●Is it crushed?
●Is it clogged with lint?
●Is the hose tip under water?
When the above problems are solved, you can resume operation by opening and closing the lid.
The lid is open.
●Did you try to run the washing machine with the lid open?
→Close the lid.
Spin or Air Dry is not possible.
●Are clothes concentrated on one side of the tub?
→Distribute the clothes evenly and close the lid.
●Is the washing machine installed on an unstable or inclined
surface?
→You can resume operation by opening and closing the lid.
Water cannot be supplied.
●Is the water faucet turned on?
→When using Temp Setting, turn on both hot and cold water faucets.
●Water outage?
●Is the water supply filter clogged with dirt? (P. 11)
→You can resume operation by opening and closing the lid.
Water has been forcibly drained.
●Water has been forcibly drained because the lid was open for 10 seconds or more
with Child Lock (P. 10) set.
→Unplug the power cord and plug it in again after 5 seconds.
Inspection is required.
●Turn off the water faucet just to be safe. Then, report the error displayed (2-digit
number after “H”) to a service person. Unplug the power cord.
(For Australia)
Phone: 132 600
Open: 8:30 a.m. to 6:00 p.m. Monday to Friday
(For New Zealand)
Phone: [phone]
Open: 8:30 a.m. to 5:00 p.m. Monday to Friday