Panduit TERMINAL BLOCK MARKERS User manual

TERMINALBLOCKMARKERS
quickstartguide
Required Components
TDP43ME-TB-KIT
Width Guide Adapter Kit
TDP43ME Printer with roll
stand (TDP43ME-RS) and
resin ribbon
Easy-Mark PlusTM
Labeling Software
step1: tdp43me firmware update
• To print terminal block markers you must have TDP43ME printer rmware version
G3.0AP1 or newer
• To check version, press and hold the FEED button while turning the printer on. Keep
holding FEED until rst 3 beeps, then let go of button.
• Self-test will print automatically, showing version number next to “TDP43ME”
(For more details see section 3-3 of TDP43ME user manual)
• If you have version G3.0AP0 or newer, proceed to step 2 below
• To upgrade your rmware, visit www.panduit.com/FirmwareUpdate
• Open the downloaded .zip le, and doubleclick on the DownloadTool 1.7.0.0f.exe le
• Click on Download Firmware
• Click on the .BIN le to highlight and select
• Click Open, printer should automatically begin rmware installation and reboot
step2: INSTALL EASY-MARK PLUStm labeling software
If you have already installed Easy-Mark PlusTM Labeling Software, then proceed to Step 3.
Existing Easy-MarkTM users:
- Visit www.panduit.com for a free upgrade to Easy-Mark PlusTM
New Easy-MarkTM users:
- Install Easy-Mark PlusTM that is provided with your TDP43ME printer
step3: Width guide Installation
Align right “R” width guide insert into
green printer guide as shown above
Use thumb to press insert horizontally
into guide, until insert snaps into place
Repeat installation for left “L” side Use ngers to widen guides
by pressing out
Use tabs on width guides to press
guides inward as needed
When changing from terminal block mark-
ers to other types of labels, use the rear
tabs on the width guide inserts to lift and
remove them from the green printer guides
1 2
3 4
5 6
Contact Panduit Identication Technical Support with any questions.
GA-T[email protected] | 866-871-4571

step4: Front Plate installation
quick start guide
12
3
Remove metal tear bar from front of
printer by rmly pulling upwards. Bar
will snap out of the tabs by which it is
attached.
Remove the existing plate from
the front of printer by pressing
releasable tabs on sides and pulling
plate out.
Install new front plate by sliding plate
downward from above the front of the
printer. Press down until the front plate
sits completely ush. If it does not sit
completely ush, ensure metal bar has
been removed.
Final Assembly Example
for
terminal block markers
Contact Panduit Identication Technical Support with any questions.
GA-T[email protected] | 866-871-4571
step5: format settings and printer driver
Two nal settings must be altered prior to successfully printing terminal block markers.
Print Driver Stop Position
• Before opening Easy-MarkTM Plus, click
on start, “Devices and Printers”
• Right click on the desired TDP43ME
printer and click “Printing Preferences”
• Click “Advanced Setup” tab
• Click “Other” button
• Change “Stop Position” to 0.00
• Close, click “Apply”, and click “OK”
• Open Easy-MarkTM Plus Labeling Software
Easy-MarkTM Plus Print Offset
• In Easy-MarkTM Plus, open a terminal
block marker format.
• Click “Print”, “Print Document”
• Select desired TDP43ME printer
• Click on “Features” button
• Change “Top Offset” to 1.5mm (0.059in)
if using TB05X12, TB06X12, & TB08X12.
• Change “Top Offset” to 2.49mm (0.098in)
if using TB05X08 & TB06X08.
• Check box for “Save Offsets” B21006 Rev. 1