Panorama Antennas MiMo User manual

Installation
Instructions
Ultra Wideband MiMo Antenna
WMMG Range
SW3-665 - v2

Installation Instructions
Contact Information
Content
3
EN
4-9
10

1. Selecting a Position
4
Note: Signal strength indication may be displayed either:
a. Graphically with bars, (where more bars is a better signal), or
b. As a signal level value in dBm (e.g. -80) - in this case, the lower the negative number, the better the
signal, (i.e. -71 is stronger signal than -83).
1.1.
1. Connect the antenna to your router or modem with the antenna adapter (if applicable) and coaxial
cable provided.
2. Ensure that your device is connected to the network and displaying the signal strength indicator.
3. With the antenna at selected location, rotate it in approximately 45 degree steps – in each position, you
may need to wait for up to one minute to allow the signal strength indicator to update.
Check that all the contents are in the box - This should include:
1.2. Select Position
1
1 x Antenna
1 x Desk Stand
2 x Wall Bracket Plates
1 x U-Bolt
1 x U-Bolt Plate
2
For a good installation the antenna should
be directed towards the strongest network
signal. In order to achieve this follow the
guide below:
4 x Screws
4 x Plain Washers
4 x Spring Washers
2 x Nuts

5
1.3. Mounting the Antenna
Mounting the antenna internally
To mount the antenna internally use the supplied desk stand and follow the instructions at 5. DESK
MOUNTING INSTRUCTIONS
Mounting the antenna externally
Mounting the antenna outside will provide optimum signal strength and data rates. Begin by following the
instructions at 1.2 concerning position and orientating the antenna. Then follow 3. MAST MOUNTING
INSTRUCTIONS or 4. WALL MOUNTING INSTRUCTIONS depending upon the equipment you have
available.
2. Important Information
RF Safety Note -Ensure that the antenna is mounted in such a way that no person is likely to be within
a distance of 30cms (12”) from the antenna during use.
RF Safety Note - Ensure that the antenna is used only as supplied the co-axial cables should not be cut
shorter or otherwise modified.
Waste electrical products should not be disposed of with household waste. All electronic products with
the WEEE logo must be collected and sent to approved operators for safe disposal or recycling. Please
recycle where facilities exist. Many electrical/electronic equipment retailers facilitate “Distributor Take-
Back scheme”for household WEEE. Check with your Local Authority or electronic retailers for
designated collection facilities where WEEE can be disposed of for free.
CE Note RoHS 2 compliance is declared per Directive 2011/65/EU and its subsequent amendments
with exemption 6.c applied. This product contains lead as an alloying element in a copper alloy
containing up to 4% lead by weight.
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals, EC 1907/2006). This
product contains Lead (CAS No. 7439-92-1) which is classified as an SVHC (Substance of Very High
Concern) as being toxic to reproductionunder Article 57c. of REACH.
Electrical Caution - Parts of this antenna are an electrical conductor. Contact with power lines can
result in death or serious injury. The antenna and supporting mast must not be close to any power lines
during installation, use or removal. If the antenna is elevated and at risk from lightning strike it must be
ensured that the antenna is mounted and earthed appropriately by a trained professional in accordance
with the relevant standards.

6
3. Mast Mounting Instructions
1 - To Mast Mount this antenna you
will need:
1 x Antenna
1 x U-Bolt
1 x U-Bolt Plate
2 - Mast Mounting the antenna externally
Ensure that the selected mounting location can be safely accessed with the equipment that you have
available and mount the antenna so that it has at least 1 metre (3.3’) of clearance from all obstructions if
possible. The antenna should not be mounted directly on to metal masts or poles. If the antenna must
be mounted to such a surface it must be mounted at the lip of the roof or the very top of the pole such
that the body of the antenna is elevated clear of the metal surface.
3 - Ensure a safe connection
Secure the antenna in place and waterproof the exposed connections. Fully tighten the mounting
hardware. If exposed the RF connector joint should be waterproofed with a weatherproof electrical tape
(self amalgamating type is recommended) allowing a significant overlap of each turn and ensuring that
the overlap is in the opposite direction to predicted water fall.
12
3
2 x Washers
2 x Spring Washers
2 x Nuts

7
12
3
4
4. Wall Mounting Instructions

8
1 - To Wall Mount this antenna you will need:
1 x Antenna
2 x Wall Bracket Plates
4 x Screws
1 - To Desk Mount this antenna you will need:
1 x Antenna
1 x Desk Mount
2 - Fix the mounting bracket to the external wall or other flat surface using suitable screws and wall plugs
(not supplied).
3 - Fix the mounting bracket to the antenna using the washers and screws supplied.
4 - Fix the antenna to the wall mounting bracket
5 - Secure the antenna in place and waterproof the exposed connections. Fully tighten the mounting
hardware. If exposed the RF connector joint should be waterproofed with a weatherproof electrical tape
(self amalgamating type is recommended) allowing a significant overlap of each turn and ensuring that
the overlap is in the opposite direction to predicted water fall.
2 - Using the Antenna Internally
When using the antenna internally, take care to ensure that the antenna or cables do not cause a trip
hazard. The antenna can be fitted to the supplied desk stand for internal use. Optimum performance will
be achieved with the antenna facing a window in the direction of best network signal strength.
3 - Mounting and dismounting the antenna to the desk stand
Once you have determined the desired mounting location and orientation you can mount and dismount
the antenna to the supplied desk stand following the steps below.
4 x Washers
4 x Spring Washers
2 x Nuts
5. Desk Mounting Instructions

9
4 - Mounting the Antenna
Hold the antenna cable securely upwards against the back of the antenna. Push the mounting foot of the
antenna down into the groove in the base so that the mounting holes sit flush with the pegs in the base
as shown.
Holding the antenna and base securely push the antenna back into the base until the pegs locate.
5 - Dismounting the Antenna
Grip the base securely from below and the antenna at the top edge.
Pull the top of the antenna away from the base stand whilst lightly squeezing the base in order to pivot
the foot of the antenna out of the trough in the desk stand as shown.
Once the foot of the antenna is unlocked from the desk stand pull the antenna forwards and upwards
from the base freeing

10
Contact Information
Panorama Antennas Ltd
Panorama Antennas Inc
[e-mail]
61 Frogmore, Wandsworth, London, SW18 1HF
[phone]
USA
[email protected]om
[phone]
1551 Heritage Parkway, Suite 101, Mansfield, TX, 76063
Panorama Antennas Pty Ltd
Panorama Antennas SAS
Unit 1, 5 Jaggs Way, Kardinya, WA 6163
Australia
[phone]
[email protected]
France
[email protected]
[phone]
16 Allée des Acacias, 33700 Mérignac
Panorama Antennas Pte Ltd
Singapore
[email protected]
[phone]
Space@ Tampines, 18 Tampines Industrial Crescent, 528605
Panorama Antennas Ltd
Germany
[email protected]
[phone]