Panorama Antennas GPS25 Series User manual

Installation Instructions
GPS[2]5 Series
SW3-1035 - v3
1. Introduction
The GPS[2]5 antenna series is a range of high-performance L1/L2/L5 and L1/L5 band GPS/GNSS antennas with excellent ltering. The antenna module is
housed within a low prole, robust enclosure and is suitable for use with GPS, GLONASS, Galileo and BeiDou systems requiring high accuracy for naviga-
tion, RTK and other precision applications.
The antenna is available in panel mount (GPS[2]5P) and magnetic / adhesive mount (GPS[2]5MS) variants. The GPS[2]5P can be installed on a metal or
plastic panel. The GPS[2]5MS can be attached by magnetic adhesion on a ferromagnetic panel. For other mounting surface materials, the adhesive pad
can be used.
The antenna is supplied with integral ame retardant RG174 cable (compliant to UN ECE R118), and is suitable for many installation environments.
2. Mounting requirements and selecting location
The antenna should be mounted with a clear view of the sky for optimal satellite acquisition.
If utilising the adhesive pad it is recommended that the installation is carried out when the temperature is higher than 50°F (10°C) - the ideal temperature for
the pad bonding is in the range of 70°F (21°C) to 100°F (37°C).
For the panel mount version, ensure that there is adequate under panel clearance and that there is no double skin panel or cross brace present.
Measure to check for central position if applicable.
For optimal performance the antenna should, if possible, be mounted at least 300mm (1ft) away from other conductive objects on the mounting panel.
3. Panel Mounting
Mask panel area around hole position to protect paintwork and headliner. Drill a pilot hole, and then increase to 19mm
(3/4”), ensuring that drill/ cutter bit does not contact headliner. Clean area around the hole, carefully removing all swarf.
Apply some petroleum jelly or paint around the hole to prevent corrosion if necessary.
Remove protective backing from underside of antenna and feed coaxial cable through panel. Position the antenna over the
hole and stick to panel by applying rm downward pressure. Assemble washer & nut from underside and tighten.
IMPORTANT: Do not exceed a torque of 5Nm (3.6ft/lbs) when tightening the mounting nut.
Hole
∅19
4. Adhesive Mounting
Make sure that the selected mounting surface is clean and dry. De-grease suface with 70% isopropyl alcohol (allowing time to dry) if required. The
magnetic / adhesive version of the antenna is supplied with an anti-scratch pad tted as standard and this should be removed before the adhesive pad is
tted to the antenna. Once the anti-scratch pad has been peeled o󰀨, remove protective backing from supplied adhesive pad and adhere to underside of
antenna, position the antenna over desired location, remove remaining protective backing and stick to panel by applying rm downward pressure.
This product contains an active GPS/GNSS antenna.
GPS25 part numbers contain an L1/L2/L5 GPS/GNSS antenna: Rated voltage: 3-12VDC Rated current: 35mA maximum
GPS5 part numbers contain an L1/L5 GPS/GNSS antenna: Rated voltage: 3-5VDC Rated current: 37mA maximum
The supply to these devices must be provided with overcurrent protection of 1A maximum.

7. Commission and Test
● Check the GPS cable with DC to measure high resistance.
● Connect the GPS cable to the GPS receiver and check for satellite acquisition.
8. Notices
DO NOT
• operate the equipment in an explosive atmosphere.
• attempt to install the antennas without the proper safe equipment to access the install location.
• install the antenna in such a way that it may fall and cause injury.
• chew parts or put them in mouth, keep away from unsupervised children.
European Waste Electronic Equipment Directive 2002/96/EC
Waste electrical products should not be disposed of with household waste. All electronic products with the WEEE logo must be
collected and sent to approved operators for safe disposal or recycling. Please recycle where facilities exist. Many electrical/electronic
equipment retailers facilitate “Distributor Take-Back scheme”for household WEEE. Check with your Local Authority or electronic
retailers for designated collection facilities where WEEE can be disposed of for free.
Waiver: This document represents information compiled to the best of our present knowledge. It is not intended to as a representation or warranty of tness of the products described for any particular pur-
pose. This document details guidelines for general information purposes only. Always seek specialist advice when planning installations and ensure that antennas are always installed by a properly qualied
installer in compliance with local laws and regulations.
6. Routing and terminating coaxial cables
Route the coaxial cable to the equipment, ensuring that the cable is secured and protected from subsequent damage during access. The cable should be
routed observing the minimum bend radius of 13mm (1/2”). If cable ties are used, they should not be overtightened, as this could distort the cable prole
and a󰀨ect the antenna performance.
5. Magnetic Mounting
Check that the vehicle has a steel roof as the mount will not work on plastic or alloy bodies. The mount has a scratch resistant pad which is suitable for
direct contact with the roof. No other material should be placed under the antenna base as this will reduce the magnetic adhesion. Make sure that the
selected mounting surface is clean and dry before placing the antenna in position.
IMPORTANT: Never attempt to detach, reposition or transport the antenna using only the cable as this may damage the cable connection.
Please Recycle
Printed versions of these instructions can be recycled. When you have nished with these instructions please recycle them.