Paradyne JetFusion Integrated Access Device User manual

JetFusion
Integrated Access Device
User’s Guide
Document No. 2000-A2-GB20-10
February 2004

2000-A2-GB20-10 - A - February 2004
Copyright © 2004 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For
additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Paradyne worldwide office locations, use one of the following methods:
 Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
 Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to [e-mail]. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
ACCULINK, COMSPHERE, ETC, EtherLoop, FrameSaver, GranDSLAM, Hotwire, the Hotwire logo, Jetstream, MVL,
NextEDGE, OpenLane, Paradyne, the Paradyne logo, Paradyne Credit Corp., the Paradyne Credit Corp. logo,
Performance Wizard, StormPort, and TruePut are all registered trademarks of Paradyne Corporation. ADSL/R,
BitStorm, Connect to Success, GrandVIEW, Hotwire Connected, iMarc, JetFusion, JetVision, MicroBurst,
PacketSurfer, ReachDSL, Spectrum Manager, StormTracker, and TriplePlay are trademarks of Paradyne Corporation.
All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or
registered service marks of their respective owners.

2000-A2-GB20-10 - i - February 2004
7DEOHRI&RQWHQWV
Preface
Audience.................................................................................. xi
Contents .................................................................................. xi
Safeguards ..............................................................................xii
Product Warranty....................................................................xiii
Conventions............................................................................xiii
Regulatory Notices .................................................................xiii
Chapter 1 Introduction
Data Interfaces .........................................................................2
JetFusion 2/4/8-Port IAD Family...............................................2
Front Panel Power and Status Indicators............................3
Rear Panel Connectors.......................................................4
JetFusion 16/24-Port IAD Family..............................................4
Front Panel Power and Status Indicators............................5
Rear Panel Connectors.......................................................6
Chapter 2 Quick Start Guide
Unpacking the IAD....................................................................9
Installing the IAD ......................................................................9
Connect via Terminal Emulator...............................................10
Setting the Ethernet Port IP Address ................................12
Resetting the IAD ...................................................................14
Connecting via Telnet .............................................................15
Running Telnet ..................................................................15
Using the Menu Interface .......................................................16

2000-A2-GB20-10 - ii - February 2004
Basic IAD Configur-ation ........................................................19
Connecting LAN, WAN, USI and Telephones.........................19
Ethernet LAN Connection .................................................19
WAN Connections.............................................................19
USI Connection (16/24-Port) ............................................20
Telephone Connections.....................................................20
Confirming Proper Setup........................................................21
Chapter 3 Administration
IAD Security............................................................................23
RADIUS Server Settings ........................................................26
Setting Up SNMP ...................................................................28
Using the SNMP Configuration Menu ...............................28
Upgrading the System ............................................................32
Setting up Your LAN Connection............................................34
Using System Utilities.............................................................35
Managing Configuration Files ...........................................37
Using the File System.............................................................39
Using the Debug Menu...........................................................41
Performing File Transfers .......................................................43
Using File Transfer Utilities ...............................................44
Setting Derived Timing Options..............................................46
Verifying an IP Address ..........................................................47
Verifying an IP Address for Windows Systems .................47
Verifying the IAD IP Addresses .........................................47
Chapter 4 WAN Configuration
Basic WAN Setup Tasks.........................................................48
Using the WAN Configuration Menu.......................................52
Selecting the Datalink Protocol...............................................53
Setting Up TDM Voice ............................................................54
Selecting the Physical Interface .............................................55

2000-A2-GB20-10 - iii - February 2004
Configuring the G.SHDSL Interface........................................56
Configuring the SDSL Interface—JF2100 ..............................59
Configuring the SDSL Interface..............................................60
Configuring the ADSL Interface..............................................64
Setting the Interface to T1 or E1.............................................65
Configuring the T1 Interface...................................................66
Configuring the E1 Interface...................................................71
Configuring ATM PVCs...........................................................75
Adding a PVC....................................................................75
Modifying a PVC ...............................................................78
Deleting a PVC..................................................................83
Showing Current PVCs .....................................................84
Configuring
ATM Options .....................................................................84
Configuring
Frame Relay DLCIs...........................................................86
Modifying a DLCI...............................................................87
Adding a DLCI...................................................................88
Deleting a DLCI.................................................................90
Displaying Current DLCIs..................................................90
Configuring
Frame Relay Options ........................................................90
Quick Configuration................................................................95
Chapter 5 Router Configuration
Basic Router Setup Tasks ......................................................97
Router Configuration Menu ....................................................98
Configuring
a Port IP Address..............................................................98
Unconfiguring a Port IP Address ..........................................100
Setting the Port Maximum Transmission Unit ......................101
Enabling and Disabling RIP..................................................101
Enabling and Disabling RIP Poisoned Reverse by Port..101
Setting the RIP Version...................................................102

2000-A2-GB20-10 - iv - February 2004
Managing Static and Default Routes ....................................103
Setting the Default Route .....................................................105
Configuring DNS Client ........................................................106
Configuring DHCP Client......................................................107
Configuring DHCP Relay......................................................108
Configuring the Telnet Server Port .......................................109
Configuring IP Filtering.........................................................109
Configuring IP Header Compression (IPHC)........................ 116
Configuring the LAN IP Broadcast Destination..................... 116
Displaying the Route Table................................................... 116
Chapter 6 Bridge Configuration
Basic Bridge Setup Tasks..................................................... 119
Bridge Configuration Menu...................................................120
Enabling and Disabling Bridging...........................................120
IP Over Bridging..............................................................120
Enabling or Disabling Bridging Globally ..........................121
Enabling or Disabling Bridging by Port............................121
Setting the Bridge Aging Timer.............................................122
Enabling and Disabling STP.................................................123
Enabling or Disabling STP Globally ................................123
Enabling or Disabling STP by Port..................................123
Configuring Spanning Tree Bridge Priority ...........................124
Configuring Spanning Tree Port Priority ...............................124
Configuring Spanning Tree Hello Time.................................125
Configuring Spanning Tree Maximum Age...........................125
Configuring Spanning Tree Forward Delay ..........................125
Configuring Spanning Tree Path Cost ..................................125
Deleting a Bridge Forwarding Database Entry .....................126
Chapter 7 Voice Path Configuration
Basic Voice Path Setup Tasks..............................................127

2000-A2-GB20-10 - v - February 2004
Voice Path Configuration Menu............................................128
Setting the Voice Gateway ...................................................128
Setting Jitter Delay ...............................................................130
Displaying Jitter Delay ..........................................................130
Setting Start Mode ................................................................130
Setting SLIC Control Mode...................................................132
Setting Compander Mode.....................................................132
Set On Hook Transmission Mode.........................................133
Setting Idle Voltage Mode.....................................................133
Setting Debug Mode.............................................................134
Configuring Echo Cancellation .............................................134
Setting Loop Gain.................................................................135
Setting Country Mode...........................................................137
Managing MGCP Embedded Client .....................................138
Managing Copper-Com Call Control ....................................142
JetStream Call Control Settings............................................144
Configuring AAL2/LES CAS .................................................146
Configuring for AAL2/LES CAS.......................................146
Configuring AAL2/LES CCS-ELCP ......................................150
Chapter 8 Firewall Configuration
Creating a Firewall via IP Filtering........................................154
Chapter 9 DHCP Server Configuration
Basic DHCP Server Setup Tasks .........................................155
The DHCP Server Configur-ation Menu...............................156
Using DHCP Debugging Messages .....................................156
Enabling and Disabling DHCP Server..................................156
Enabling and Disabling Checking for Additional DHCP Servers157
Configuring DHCP Server Parameters.................................157
Configuring
the DHCP Address Range Pool......................................158

2000-A2-GB20-10 - vi - February 2004
Configuring a DHCP Client Entry .........................................158
Displaying DHCP Server Details ..........................................160
Displaying DHCP Server Statistics .......................................161
Displaying DHCP Server Assigned and Unassigned Addresses161
Displaying DHCP Entry Details ............................................162
Deleting a DHCP Client Entry...............................................162
Deleting a DHCP Assign-ment Entry....................................162
Chapter 10 Multicast Configuration
Configuring Multicast............................................................163
Enabling and Disabling Global IP Multicast..........................164
Configuring PIM—Dense Mode by Port ...............................164
Managing Multicast Route Source........................................165
Adding a Multicast Routing Source ......................................165
Removing a Multicast Routing Source .................................166
Displaying the Multicast Routing Source ..............................166
Displaying the IGMP Group..................................................166
Displaying the IGMP Querier................................................167
Displaying the Multicast Routing Table.................................167
Displaying the PIM Neighbor................................................168
Chapter 11 NAT Configuration
The NAT Configuration
Menu ...............................................................................170
Enabling NAT Translation.....................................................171
Configuring
NAT Local Server ............................................................172
Configuring
NAT Timeouts..................................................................173
Configuring
the NAT Port Range ........................................................174
Configuring
the NAT Alias Entry.........................................................175
NAT Statistics .......................................................................176

2000-A2-GB20-10 - vii - February 2004
NAT Connection Table..........................................................177
NAT Connection Details .......................................................177
NAT Local Server Table........................................................179
NAT Alias Table ....................................................................179
Deleting IP Addresses from NAT Tables ..............................179
Deleting a NAT Local Server Entry.......................................180
Deleting a NAT Alias Entry ...................................................180
Chapter 12 IAD Reports
The Report Menu..................................................................181
Current Configur-ation Report ..............................................182
Network Statistics Reports....................................................184
Interface Statistics Reports...................................................193
Media Statistics Reports .......................................................205
Route Table Report...............................................................217
ARP Table Report.................................................................217
Bridge Forwarding Database Report ....................................217
Bridge Status Report ............................................................218
PPP Authorization Entries Report ........................................218
System Uptime Report .........................................................219
Memory Statistics Reports....................................................219
Zero All Statistics..................................................................220
Chapter 13 Command Line Interface
Intro-duction..........................................................................221
set wan stp bridge ................................................................221
Command Line Interface Reference.....................................223
exit........................................................................................223
ping.......................................................................................223
quit........................................................................................223
rename file............................................................................223
reset system .........................................................................224

2000-A2-GB20-10 - viii - February 2004
remove lan ip address ..........................................................224
set bridge global ...................................................................224
set bridge stp global .............................................................225
set dhcp server enable .........................................................225
set dhcp server gateway.......................................................225
set dhcp server subnet .........................................................225
set dhcp server dns ..............................................................225
set dhcp server netbios ........................................................225
set dhcp server domain ........................................................225
set dhcp server range...........................................................226
set dns server address .........................................................226
set ip default route................................................................226
set ip route............................................................................226
set lan bridge........................................................................227
set lan ip address .................................................................227
set lan rip..............................................................................228
set lan stp bridge ..................................................................228
set mgcp bracketing .............................................................228
set mgcp listening port..........................................................228
set mgcp notified entity.........................................................229
set mgcp signaling connection .............................................229
set mgcp signaling port.........................................................229
set mgcp signaling tos..........................................................229
set mgcp voice connection ...................................................229
set mgcp voice tos................................................................230
set nat...................................................................................230
set sdsl speed.......................................................................231
set system defaults...............................................................231
set wan atm ppp auth ...........................................................231
set wan atm vc......................................................................232
set wan bridge ......................................................................232
set wan datalink....................................................................233
set wan framerelay ...............................................................233

2000-A2-GB20-10 - ix - February 2004
set wan ip address................................................................234
set wan stp bridge ................................................................234
set wan rip ............................................................................235
show configuration................................................................235
show dhcp server configuration............................................235
show ip routes ......................................................................235
tftp receive ............................................................................235
Chapter 14 Troubleshooting and Diagnostics
Using the Diagnostics
Menu ...............................................................................237
POTS Diagnostics ................................................................237
SDSL Diagnostics.................................................................242
ISDN-BRI Diagnostics ..........................................................243
Troubleshooting the IAD.......................................................244
Chapter 15 Verification
Power-up Test.......................................................................247
Operational Test ...................................................................247
Maintenance.........................................................................248
Displaying the Current Configuration....................................248
Appendix A Menu Map
Menu Map.............................................................................250
Appendix B Country Codes
Country Codes Tables ..........................................................252
Appendix C JetFusion IAD Specifications
Equipment List......................................................................254
2/4/8-Port..............................................................................255

2000-A2-GB20-10 - x - February 2004
16/24-Port.............................................................................262
Appendix D Connector Pinouts
Connector Pinouts ................................................................265
Appendix E Glossary
Glossary ...............................................................................268
Index

2000-A2-GB20-10 - xi - February 2004
The JetFusion Family IAD User Guide contains the information you need
to install, connect and configure each JetFusion IAD in a customer’s
premises.
Audience This guide is intended for network engineers and other professionals in the
telecommunications industry who are engaged in the installation,
configuration, management and support of telephone and computer
networks, network access products, and related equipment.
Contents The guide contains the following chapters and appendixes:
This preface describes the audience, how this guide is organized,
safeguards you should always observe, and warranty and regulatory
notices.
Chapter 1, Introduction on page 1, introduces the features of the IADs,
including the hardware, indicators and ports.
Chapter 2, Quick Start Guide on page 8, describes the process of getting
an IAD up and running in a typical customer premises. This chapter is
helpful if you are new to IADs, because it lists each step, beginning with
unpacking the IAD. It also provides information about logging on, using the
menu interface, setting the IP address, basic configuration tasks and
restarting the IAD. Once you have read this chapter, you will be well-
prepared to use the remaining reference chapters.
Chapter 3, Administration on page 22, provides information about IAD
security, configuring Simple Network Management Protocol (SNMP),
upgrading ACOS, system utilities and other topics.
Chapter 4, WAN Configuration on page 48, details how to configure the
JetFusion IAD for physical connection to the network—T1/E1 and xDSL,
Frame Relay and ATM, and TDM Voice for channelized T1 circuits.
Chapter 5, Router Configuration on page 96 describes the steps to
configure the IAD as a router, including setting IP addresses, static routes,
configuring RIP, DNS Client, DHCP Client and other router settings.
Chapter 6, Bridge Configuration on page 118, provides details about
setting up the IAD as a bridge, including setting bridging globally or by
port, setting the aging timer, and enabling Spanning Tree support.
Chapter 7, Voice Path Configuration on page 127, describes how to set up
voice ports for use in various DSLAM and voice gateway environments.
3UHIDFH

2000-A2-GB20-10 - xii - February 2004
Chapter 8, Firewall Configuration on page 154, provides information about
setting up the IAD to perform IP filtering.
Chapter 9, DHCP Server Configuration on page 155, walks you through
the steps required to configure the Dynamic Host Configuration Protocol
(DHCP) server and client.
Chapter 10, Multicast Configuration on page 163, describes the steps to
configure the IAD to perform Network Address Translation (NAT).
Chapter 11, NAT Configuration on page 169, describes the steps required
to configure the IAD to perform Network Address Translation (NAT).
Chapter 12, IAD Reports on page 181, describes each report you can run.
Chapter 13, Command Line Interface on page 221, describes how to enter
and exit CLI mode, and how to use each command in the command line
interface. You may use these commands instead of using the
corresponding commands in the menu interface.
Chapter 14, Troubleshooting and Diagnostics on page 236, shows you
how to troubleshoot and diagnose your IAD configuration when abnormal
symptoms occur in the voice or computer network.
Chapter 15, Verification on page 247, describes the steps you take to
verify normal operation once you’ve installed, connected and configured
the IAD. It also covers maintenance and how to display the current
configuration.
Appendix A, Menu Map on page 250, provides a graphic view of the IAD
menu interface, illustrating its navigation and organization.
Appendix B, Country Codes on page 252, lists the specifications for each
country code supported in the IAD.
Appendix C, JetFusion IAD Specifications on page 254, lists the
specifications for each IAD.
Appendix D, Connector Pinouts on page 265, provides interface pinout
information for each type of port on the IADs.
Safeguards You should read and understand the following precautions and warnings
before using the JetFusion IAD. You should post these precautions in a
clearly visible location near each IAD.
The Safety status of the SLIC ports on this product are defined as TNV
-2. Therefore, cables attached to them should not be subject to over
voltage. To ensure this they should not leave the building in which the
Unit is installed.
Close supervision is necessary when the system is used by or near
children. Do not leave unattended while in use.
Only use electrical extension cords with a current rating equal to that of
the system.
Always disconnect the system from power before cleaning and
servicing and when not in use.
Do not spray liquids directly onto the system when cleaning. Always
apply the liquid first to a static free cloth.
Do not immerse the system in any liquid or place any liquids on it.

2000-A2-GB20-10 - xiii - February 2004
Do not disassemble this system (except as instructed in the
manufacturer’s instructions). To reduce the risk of shock and to
maintain the warranty on the system, a qualified technician must
perform service or repair work.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
Keep ventilation openings free of any obstructions.
SAVE THESE INSTRUCTIONS.
Product
Warranty
Each JetFusion IAD is warranted to be free from manufacturer’s defects
for the period of one year from the date of original purchase.
Conventions Some paragraphs display a symbol in the margin. These paragraphs
contain important notes or warnings, or information that is specific to one
or more IADs.
Regulatory
Notices FCC Notice
All JetFusion products except the JF2004 have been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a Commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
The JF2004 has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not in-stalled and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
NOTE Information in this style of paragraph is special information
you should be aware of as you proceed with the task at hand.
CAUTION Information in this style of paragraph indicates important
personal safety information you should heed, or voice
operations that may be interrupted if you continue.
LANLINK LAN ACT WAN LINK VOICEPOWER
JF2104 This paragraph alerts you to information that is specific to one
or more IADs, listed immediately to the left of the text.

2000-A2-GB20-10 - xiv - February 2004
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Paradyne could void
the user’s authority to operate this equipment.
The JetFusion models below comply with Part 68 of the FCC Rules. On
the bottom of the base of this equipment is a label that contains, among
other information, the FCC Registration Number and Ringer Equivalence
Number (REN) for the equipment. You must, upon request, provide this
information to your telephone company.
NOTE: REN is not required for some types of analog or digital facilities.
Before connecting your IAD, you must inform the telephone company of
the following information.
An FCC compliant telephone cord and modular plug is provided with this
equipment. This equipment is designed to be connected to the telephone
network or premises wiring using a compatible modular jack that is Part 68
compliant. See installation instructions for details. The REN is useful to
determine the quantity of devices you may connect to your telephone line
and still have all those devices ring when your telephone number is called.
In most, but not all areas, the sum of the RENs of all devices connected to
one line should not exceed five (5). To be certain of the number of devices
you may connect to your line, as determined by the REN, you should
contact your local telephone company to determine the maximum REN for
your calling area.
NOTE: REN is associated with loop-start and ground-start ports. Do not
use for E&M or digital ports.
If your telephone equipment causes harm to the telephone network, the
Telephone Company may discontinue your service temporarily. If possible,
they will notify you in advance. However, if advance notice is not practical,
you will be notified as soon as possible. You will be informed of your right
to file a complaint with the FCC.
IAD SOC/REN USOC FIC
JF2208, JF2216,
JF2224
SOC = 6.0N RJ48C 04DU9.BN,
04DU9.DN,
04DU9.1KN,
04DU9.1SN
JF2004, JF2008 REN = 0.0B RJ11C -

2000-A2-GB20-10 - xv - February 2004
Your telephone company may make changes in its facilities, equipment,
operations, or procedures that could effect the proper functioning of your
equipment. If they do, you will be notified in advance to give you an
opportunity to maintain uninterrupted telephone service.
If you experience trouble with the IAD, please contact your service
provider for information on obtaining service or repairs. The Telephone
Company may ask that you disconnect this equipment from the network
until the problem has been corrected or until you are sure that the
equipment is not malfunctioning. No user serviceable parts are contained
in this equipment. This equipment may not be used for coin service
provided by the Telephone Company. Connection to party lines is subject
to state tariffs. Contact the state Public Utilities Commission or Corporation
for information. Do not attempt to repair this equipment yourself.
Industry Canada Notice
“NOTICE: The Industry Canada label identifies certified equipment. This
certification means that the equipment meets telecommunications network
protective, operational and safety requirements as prescribed in the
appropriate Terminal Equipment Technical Requirements document(s).
The Department does not guarantee the equipment will operate to the
user's satisfaction.
Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local telecommunications company.
The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some
situations. Repairs to certified equipment should be coordinated by a
representative designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic water
pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or
electrician, as appropriate.”
“NOTICE: The Ringer Equivalence Number (REN) assigned to each
relevant terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence
Numbers of all the devices does not exceed 5.”
Underwriters’ Laboratories’ Statement
These systems are intended to be powered only by the power supply unit
provided.

2000-A2-GB20-10 - xvi - February 2004
CE Mark
These JetFusion products have been marked with the CE mark. This mark
indicates compliance with EEC Directives 89/336/EEC, 73/23/EEC 1999/
5/EC.
Warning
All JetFusion products except JF2004 are Class A products. In a domestic
environment these products may cause radio interference in which case
the user may be required to take adequate measures
A full copy of the declaration of Conformity can be obtained from Polyspan
Ltd., Whichford House, Parkway Court, Oxford Business Park South,
Oxford, OX4 2JY, UK
Declaration of Conformity:
Hereby, Polyspan Ltd. declares that this JetFusion is in compliance with
the essential requirements and other relevant provisions of Directive
1999/5/EC.
Konformitetserklæring:
Hermed erklærer Polyspan Ltd., at indestående JetFusion er i
overensstemmelse med de grundlæggende krav og de relevante punkter i
direktiv 1999/5/EF.
Konformitätserklärung:
Hiermit erklärt Polyspan Ltd., dass der JetFusion die grundlegenden
Anforderungen und sonstige maßgebliche Bestimmungen der Richtlinie
1999/5/EG erfüllt.
Vaatimustenmukaisuusvakuutus:
Polyspan Ltd. vakuuttaa täten, että JetFusion on direktiivin 1999/5/EC
keskeisten vaatimusten ja sen muiden tätä koskevien säännösten
mukainen.
Déclaration de conformité :
Par la présente, Polyspan Ltd. déclare que ce JetFusion est conforme aux
conditions essentielles et à toute autre modalité pertinente de la Directive
1999/5/CE.
Dichiarazione di conformità:
Con la presente Polyspan Ltd. dichiara che il JetFusion soddisfa i requisiti
essenziali e le altre disposizioni pertinenti della direttiva 1999/5/CE.
:
  ,  Polyspan Ltd.     
JetFusion       
  1999/5/ K.

2000-A2-GB20-10 - xvii - February 2004
Verklaring van overeenstemming:
Hierbij verklaart Polyspan Ltd. dat diens JetFusion voldoet aan de
basisvereisten en andere relevante voorwaarden van EG-richtlijn 1999/5/
EG.
Declaração de Conformidade:
Através da presente, a Polyspan Ltd. declara que este JetFusion se
encontra em conformidade com os requisitos essenciais e outras
disposições relevantes da Directiva 1999/5/CE.
Declaración de conformidad:
Por la presente declaración, Polyspan Ltd. declara que este JetFusion
cumple los requisitos esenciales y otras cláusulas importantes de la
directiva 1999/5/CE.
Överensstämmelseförklaring:
Polyspan Ltd. förklarar härmed att denna JetFusion överensstämmer med
de väsentliga kraven och övriga relevanta stadganden i direktiv 1999/5/
EG.

2000-A2-GB20-10 - 1 - February 2004
This chapter introduces the JetFusion Integrated Access Devices (IAD)
and describes their hardware and software. You should be aware of the
characteristics of each IAD to properly install and configure them for
operation in a customer’s premises.
This chapter provides information about these topics:
JetFusion 2/4/8-port IAD features, indicators and connectors (page 2)
JetFusion 16/24-port IAD features, indicators and connectors (page 4)
JetFusion IADs are ideal for service providers offering small to medium
businesses (or business units) a high quality voice and data service over
broadband circuits. With up to 24 POTS ports and full LAN support with a
full range of integrated features, each IAD offers toll-quality voice and high
speed Internet access over a single copper pair in one unit.
Each IAD supports any POTS device via its voice subsystem, and any IP-
based computer system (Ethernet printers, personal computers—
Windows, Macintosh, Unix, Linux, etc.— network file servers, and other
network devices) via its LAN subsystem.
Figure 1–1. JetFusion Integrated Access Devices
,QWURGXFWLRQ
2/4/8-Port IAD
16/24-Port IAD
03-17481
VOICE DCE DCE
ACT
LINK
LAN LAN
ACT
LINK
WAN
LINK
POWER
JetFusion
03-17482