Parkmatic PRO OES User manual

PRO22218 (Buzzer)
PRO43218 (LCD)
PRO OES
Installation Manual
810R-05 1524
Front-Rear Parking Sensor

Contents of the Box
Pro22218/43218
Installation Manual
Rear ECU
Quantity: 1pc
Front ECU
Quantity: 1pc
* Depend on Model
Sticker
Quantity: 1pc for buzzer
Sticker
Scotchlok
Sticker
Quantity: 2pc for ECU
Buzzer
* Quantity: 1pc
LCD Display
* Quantity: 1pc
Sensor
Quantity: 8pc
Rear Power Cable
Quantity: 1pc
Silicon Ring
Quantity: 8pc
Front Wire Harness
Quantity: 4pc 4,5m
Front Power Cable
Quantity: 1pc
Front On-Off Switch
Quantity: 1pc
3M 3M
3M 3M
3M
Rear Wire Harness
Quantity: 4pc 2,5m
Set Code:22218/43218
3M
3M 3M
3M
3M
3M
3M
3M
1234
Optional
16,4mm
For Flush Mount
Angled Sleeves
Quantity: 8pc
Angled Sleeves
Quantity: 8pc
Angled Sleeves
Quantity: 8pc
Drill Bit
Quantity: 1pc 20 mm
3° 6° 12°
1
5 7 8 6 B/G/A

Tools
Electric Drill Drill Bit 10mm
Drill Bit 4mm
Marker Cable Cutter
Soldering Tool
17 wrench Insulating Tape
Solder Wire
Tape Measure Screwdriver Rasp and Cutter
Testmeter
Heat Blower Alchol
Pro22218/43218
Installation Manual

Silicon ring
Flush Mount Outside Drill
Silicon ring
Angled Sleeves
3°/6°/12°
Sensor
Drill Bit 20mm
*Optional
Drill Bit 16,4mm
Sensor
Adhesive Tape
The sensors must never be directed downwards. Use the appropriate
mounting sleeves so that the sensors are in a horizontal or slightly
upwards position. The point on the front of the sleeve as well as the
arrow and the label up on the rear of the sensor must face upwards.
When mounted in the bumper, the adhesive holders can be mounted
horizontally or vertically. The arrow on the back of the
sensor and the lettering UP must always be directed upwards.
Use only this model when the sensors are horizontal or slightly upwards.
UP
UP
The sensors may only be mounted
with pressure on the sleeve
UP
The bumper surface must be dedusted and degreased before stick.
Cleaner
0,1 0,1 0,1
Felt Prime Paint Warnish
x
1
Pro22218/43218
Installation Manual
Silicon ring install after
paintwork!

Flush Mount Type
1
90 ° 90 °
1
Outside Drill Type
3° 6° 12°
3° 6° 12°
!
=<12°
2
Pro22218/43218
Installation Manual

L
3
Pro22218/43218
Installation Manual

Max. +0,2mm
cutter
For many vehicles it is advisable to remove the bumper
Leave sufficient sensor line clearance free to
allow a later change of the sensors without
disassembling the bumper (~20cm)
The drill must be held perpendicular to the
bumper surface so that the sensors can lie flat
and without pressure.
The sensors must not be
mounted very tight, as this
can lead to problems.
Since the supplied drill bit
has a very suitable diameter,
the holes can easily be
expanded as required.
Only when
using the
mounting
sleeves
Angled
Sleeves 3°
Angled
Sleeves 6°
Angled
Sleeves 12°
!
4
Pro22218/43218
Installation Manual

Mark
10 mm
S6 S8 S7 S5
S5
S7
S8
S6
inside
10 mm
!x
5
Pro22218/43218
Installation Manual

17mm
CLEAN
16.4mm
UP
UP
UP
UP
UP
UP
UP
UP
UP
UP
<70°C
1
2
3
4
5
6
6
Pro22218/43218
Installation Manual

Silicon ring
Flush Mount Outside Drill
Silicon ring
Angled Sleeves
3°/6°/12°
Sensor
Drill Bit 20mm
Sensor
Adhesive Tape
The sensors must never be directed downwards. Use the appropriate
mounting sleeves so that the sensors are in a horizontal or slightly
upwards position. The point on the front of the sleeve as well as the
arrow and the label up on the rear of the sensor must face upwards.
When mounted in the bumper, the adhesive holders can be mounted
horizontally or vertically. The arrow on the back of the
sensor and the lettering UP must always be directed upwards.
Use only this model when the sensors are horizontal or slightly upwards.
UP
UP
The sensors may only be mounted
with pressure on the sleeve
UP
The bumper surface must be dedusted and degreased before stick.
Cleaner
0,1 0,1 0,1
Felt Prime Paint Warnish
x
*Optional
Drill Bit 16,4mm
Pro22218/43218
Installation Manual
7
Silicon ring install after
paintwork!

1
Outside Drill Type
90 °
3° 6° 12°
3° 6° 12°
Flush Mount Type
90 °
1
Pro22218/43218
Installation Manual
8

L
Pro22218/43218
Installation Manual
9

45~70 cm
+ +
+
+
A
A B C D
A
B C D
50 2
+
-2
+
-2
+
-
50 50
1234
123 4
1 2
50/50/50
L = 160~200 cm
45~70 cm
A B C D
++
+
+
AA
B C D
35 50 35
1234
12
35/50/35
1234
L = 160~200 cm
2
+
-2
+
-2
+
-
45~70 cm
L = 160~200 cm
+ +
+
+
A
A B C D
AB C D
30 60 30
1234
1234
12
30/60/30
2
+
-2
+
-2
+
-
45~70 cm
A B C D
L = 160~200 cm
++
+
+
AA
B C D
20 80 20
1234
12
123 4
20/80/20
2
+
-2
+
-2
+
-
+
+1
2
The sensors can
be installed at
different heights
Different distance
adjustment can be
programing through
pc with our special
pc software.
Pro22218/43218
Installation Manual
10

For many vehicles it is advisable to remove the bumper
Max. +0,2mm
Only when
using the
mounting
sleeves
The sensors must not be
mounted very tight, as this
can lead to problems.
Since the supplied drill bit
has a very suitable diameter,
the holes can easily be
expanded as required.
cutter
The drill must be held perpendicular to the
bumper surface so that the sensors can lie flat
and without pressure.
Leave sufficient sensor line clearance free to
allow a later change of the sensors without
disassembling the bumper (~20cm)
Angled
Sleeves 3°
Angled
Sleeves 6°
Angled
Sleeves 12°
Pro22218/43218
Installation Manual
11

10 mm
S1
S1
S4
S2S3
S2 S3 S4
10 mm
Mark
inside
Pro22218/43218
Installation Manual
12

17mm
16.4mm
UP
UP UP
UP
UP
UP UP
UP
UP
UP
CLEAN
Pro22218/43218
Installation Manual
13

Pro22218/43218
Installation Manual
14
Volume
p
e
e
e
e
Bp
e
e
e
e
Bp
e
e
e
e
B
Set the volume with the slide
switch to a good audible level
Off
Off
Low
Low
High
High
Off
Low
High
Off
Low
High
Distance for
Wall
Last Zone Continuous tone
For vehicles with a spare wheel mounted on the tailgate or with
trailer coupling, the warning zone for the last zone (duration) can
be extended from 30 to 50 cm.
1234
3
3
30 cm
50 cm
Fasten the control unit
REAR

Pro22218/43218
Installation Manual
15
Option1 (FRONT) Option2 (FRONT)
Fasten the control unit
GREY (Speed)
YELLOW (Brake)
BLACK (GND)
ACC 12V +RED
on-o switch
0
20
60
80 100
120
140
160
speed

Pro22218/43218
Installation Manual
16
1234
41
Black
Red
Red
Orange
Orange Orange
Red
Red
Orange

(Ground)
(+12V Reverse Lamp (+))
(+12V Reverse Lamp (+))
(+ACC)
Solution 1
Solution 2
6 8 7 5
6 8 7 5
LCD DISPLAY
S02DSP00028
BUZZER
S12BZR00016
OR
5 7 8 6 B/G/A
YELLOW
GREY
BLACK
RED
on-o
switch
UP
Power Connection:
Red: +12V DC
Gray: Speed Signal
Yellow: Brake
Black: GND
R
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
G
I
N
C
C
S
T
A
A
F
R
F
T
O
Test lamp and
measuring equipment
ACC
Power
-Under normal circumstances, connect
the orange wire to the reverse light
+12v and black wire to ground.
-If the voltage of the reverse light is weak
or distorted, cut the red wire from the
orange wire and connect the red wire
to the reverse light +12v, the orange wire
to ACC and black wire to ground.
S6 S8 S7 S5