Parksafe Automotive CAMINTER15 User manual

Overview
Kit Contents
Power/CAN Harnesses
LVDS
Video
Cables
Interface
iR Remote
CAMINTER15
iR Remote sensor
Page 1
The CAMINTER15 will allow you to install rear camera & front/side
camera onto the factory 7" or 10" OEM touch screen fitted in the
Mercedes Sprinter 2018 onwards. This interface features active moving
guidelines and front/side cameras selectable using either OEM button or
preset timer.
PARKSAFEAUTOMOTIVE.COM

Interface
Dip Switch Sengs
Dip SW: 1 4
UP OEM RVC
DOWN ADDING RVC
*Note: Remove power to the unit prior to making adjustments to the dip switches.
5
Installaon
The installation takes place at the rear of the factory The installation takes place at the rear of the factory
SCREEN and RADIO. Certain trims and fixings will have to SCREEN and RADIO. Certain trims and fixings will have to
be removed in order to gain access to the Screen and be removed in order to gain access to the Screen and
Radio. Radio.
The installation takes place at the rear of the factory
SCREEN and RADIO. Certain trims and fixings will have to
be removed in order to gain access to the Screen and
Radio.
2 3
SCREEN RES
6
F CAM OFF
F CAM ON
POWER / CAN
DIP SWITCHES
Not Used Not Used
IR
TO SCREEN TO HARNESS
Not Used
Not Used
EXT TRIGGER
(12V+)
Keep DOWN Keep DOWN
Page 2
FOR FRONT / SIDE CAMERA ENSURE “DIP SWITCH 1" IS IN THE
DOWN POSITION
SCREEN RES
SEE BELOWSEE BELOW
7" SCREEN7" SCREEN7" SCREEN 10" SCREEN10" SCREEN10" SCREEN
PARKSAFEAUTOMOTIVE.COM

Installaon Diagram
WIRE FUNCTIONSWIRE FUNCTIONSWIRE FUNCTIONS
INTERFACE FUNCTION
RED ACC 12v+
BLACK GND
BROWN 12v+ OUTPUT (CAMERA POWER)
GREEN 12v+ REVERSE WIRE (only if it will not switch via CAN)
WHITE CAN LOW
BLUE CAN HIGH
-
-
-
-
-
-
SCREEN
FACTORY
HARNESS
(POWER)
SUPPLIED
T-HARNESS
SCREEN
FACTORY
HARNESS
(VIDEO)
REAR OF SCREEN
HARNESS AT THE
REAR OF HEAD UNIT
SUPPLIED
HARNESS
CAN
CONNECTIONS
iR REMOTE
BROWN WIRE
12v+ OUTPUT
(CAMERA POWER)
RCA
(CAMERAS IN)
F
R
Interface wires Connect to vehicle
PURPLE / WHITE
BLUE (CAN HIGH)
WHITE (CAN LOW)
CAN CONNECTIONS
PURPLE or PURPLE / BLACK
Page 3
PARKSAFEAUTOMOTIVE.COM

Installaon
USE TWO RIGHT ANGLED PICK TOOLS, SLOT
THEM DOWN THROUGH THE AIR VENT. POSITION
ONE PICK FACING DOWN AND OTHER PICK
FACING UP. YOU WILL FEEL THEY HOLD ONTO
THE CENTRE OF THE AIR VENT. HOLD THE PICKS
TIGHT AND PULL SHARPLY TOWARDS YOU, AND
THE VENT WILL POP OUT.(DON'T BE AFRAID IT
ONLY CLIPS IN).
Page 4
HOW TO REMOVE THE DASH
PARKSAFEAUTOMOTIVE.COM

Installaon
REMOVE THE T20
TORX FROM BEHIND
THE AIR VENT (LEFT
AND RIGHT VENTS)
Page 5
PARKSAFEAUTOMOTIVE.COM

Installaon
ONCE YOU HAVE REMOVED THE 2 X T20 SCREWS
FROM BEHIND THE AIR VENTS, USE A TRIM TOOL
AND PRY THE FASCIA FORWARD TO ACCESS THE
SCREEN AND HEAD UNIT.
THIS IS ONLY HELD ON WITH CLIPS, SO JUST PULL
AND IT WILL RELEASE.
Page 6
PARKSAFEAUTOMOTIVE.COM

Installaon
CONNECT THE PLUG AND PLAY POWER HARNESS
AT THE REAR OF THE SCREEN.
ALSO CONNECT THE LVDS (VIDEO CABLES) AT THE
REAR OF THE SCREEN
LVDS
Video
Cables
Page 7
PARKSAFEAUTOMOTIVE.COM

IT MAY BE NECESSARY TO TRIM THE KEYWAY ON
THE OEM BLUE POWER PLUG (AT THE REAR OF THE
SCREEN) TO FIT IN THE SUPPLIED T-HARNESS
Installaon
Page 8
PARKSAFEAUTOMOTIVE.COM

CAN CONNECTIONS
Installaon
THERE ARE 2 DIFFERENT TYPES OF HEAD UNIT FOR
THE SPRINTER. THE CAN CONNECTIONS ARE
CONNECTED AT THE SAME PLACE (REAR OF THE
HEAD UNIT). HOWEVER AS YOU SEE FROM THE
FOLLOWING PHOTOS THE PLUGS ARE DIFFERENT.
TYPE 1
Interface wires Connect to vehicle
PURPLE / WHITE
BLUE (CAN HIGH)
WHITE (CAN LOW)
CAN CONNECTIONS
PURPLE or PURPLE / BLACK
Page 9
PARKSAFEAUTOMOTIVE.COM

CAN CONNECTIONS
Installaon
TYPE 2
Interface wires Connect to vehicle
PURPLE / WHITE
BLUE (CAN HIGH)
WHITE (CAN LOW)
CAN CONNECTIONS
PURPLE or PURPLE / BLACK
Page 10
PARKSAFEAUTOMOTIVE.COM

Menu Adjustments
Before you start:
· The IR-Eye must be connected
· Make sure the car’s ignion is on and radio is on
· You must be in Reverse Camera mode (place vehicle in reverse)
· Press the OK BUTTON 4 mes (numbers will display per press), then press
POWER.
· The OSD Menu will appear on screen (auto-me out in about 5 seconds if
no acon occurs).
To acvate Front Camera mer, scroll down using the remote
arrow keys when in the menu to FRONT CAMERA. Once in
this seng, press OK and choose (up/down) between 5, 7,
9 or 11 seconds for auto-front switching meout (once the
vehicle leaves reverse gear, the front camera input will
stay acve for pre-defined amount of me).
Funconal Parking Guidelines ON/OFF
Not Used
Adjust FPG Posion
Not Used
‘Safe to move?’ ON/OFF
NOTE: Once you have finished adjusting your settings, you
must press the “POWER” button to save your settings.
Page 11
NOTE: ENSURE “DIP SWITCH 1" IS IN THE DOWN POSITION
PARKSAFEAUTOMOTIVE.COM

Operaon
Once the interface is connected properly, reverse acvaon is automac. Placing
the vehicle in reverse will display the connected camera’s image automacally.
Note: If display doesn’t switch to reverse image when shiing into reverse or screen is
distorted, check dip switch sengs on page 2.
Note: If all dip switch sengs have been tried, connect the provided ‘Reverse Trigger Input’
wire (green) and supply this wire with an OEM reverse 12v (+) signal.
FRONT / SIDE CAMERA
NOTE: ENSURE “DIP SWITCH 1" IS IN THE DOWN POSITION
To select Front / Side camera, press and hold the return
button (on the steering wheel) for 2 secs. To cancel the
camera either press and hold the return button for 2 sec or
turn off IGN, and open the drivers door.
REAR CAMERA
Page 12
PARKSAFEAUTOMOTIVE.COM