Parkside PDS 150 User manual

Operating
and safety instructions

PDS 150
2002

Kompernaß Handelsgesellschaft mbH
Burgstraße 21 · D-44867 Bochum Germany)
Operating instructions Page 4 - 7


Abb./Fig. 1
Abb./Fig. 2







+









PDS 150 BENCH GRINDER
For grinding and sharpening metal tools
Dear Customer! We are delighted that you have decided to purchase our high quality PDS 150 Bench Grinder. Please make sure you familiarise
yourself fully with the way the equipment works before you use it for the first time and that you understand how to handle electrical power
tools correctly. Please read the operating instructions below and the accompanying safety advice carefully.
Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce
better results. We hope you enjoy using your bench grinder.
FEATURES OF THE PDS 150
Mounting holes (4x) Wheel guard cover
Protection shields Wheel edge cover
Protection shield mount Grinding wheel
Workpiece support right Machine-side flange (marked with notch)
ON / OFF switch Nut with notch
Workpiece support adjustment screws Outside flange (not marked)
Workpiece support left Left-hand thread
TECHNICAL INFORMATION
Nominal voltage: 230 V ~ 50 Hz
Power consumption: 150 watts
No load speed: 2,950 rpm-1
Grinding wheel diameter: 150 mm
Grinding wheel width: 016 mm
Grinding wheel bore: 012,7 mm
Circumferential speed max.: 21.99 m/s
Weight: 7.3 kg
Sound pressure level: 73.00 dB (A) Noise level determined for normal operation /measured in accordance with DIN 45635-21
We reserve the right to make technical modifications to and changes to the appearance of the equipment in the course of further development
without notice.
Hence no responsibility is accepted for any information such as dimensions, instructions etc. This does not affect your legal rights.
IMPORTANT SAFETY ADVICE
Ensure that you observe the following safety instructions specifically for this equipment and in addition that you read the advice
in the accompanying booklet called "Safety advice" before using the equipment for the first time.
Not following the safety instructions and advice can lead to accidents, electric shock, injuries, risks to health, or burns.


4


This bench grinder is intended to be used exclusively for dry grinding.
Materials dangerous to health, such as asbestos are not to be abraded.
Wear ear protectors. Look after your health – please wear safety glasses and a breathing /dust mask.
Always keep the mains cable away from the working area of the grinder and lead the cable away from the rear of the grinder.
The equipment is not to be used by people under 16 years old.
WARNING – Danger of burning! The workpiece gets hot during grinding. Never touch the part being ground.
Allow the workpiece to cool sufficiently. When grinding for longer periods, stop grinding from time to time and allow the workpiece
to cool before continuing.
AREA OF USE
The PDS 150 Bench Grinder is intended for grinding and sharpening metal tools such as drills, chisels etc. and metal items.
We do not take any responsibility for uses other than those given here. Similarly in this event the guarantee becomes null and void.
ASSEMBLY, COMMISSIONING AND USE
 ASSEMBLY
Before commissioning for the first use, the equipment must be fully assembled with all its parts. Attach the eye shields , the workpiece
support left and the workpiece support right , see Fig. 1). The bench grinder must be mounted on to a robust level surface, and if at all
possible on to a fixed support, e.g. working surface, workbench. Use the four mounting holes .
 POSITIONING WORKPIECE SUPPORTS AND EYE SHIELDS
To ensure safe working, the workpiece supports /and the eye shield mounts must be correctly positioned. Check and correct
the settings at frequent intervals to ensure even wear on the grinding wheel .
The clearance between the grinding wheel and the eye shield holder , and between the grinding wheel and the workpiece support
(or ) must be no more than 2 mm.
Pull out the mains plug and loosen the workpiece support adjustment screw for setting. Bring the workpiece support close up to grinding
wheel until the wheel just not longer moves. This is the correct setting. Retighten the adjustment screw and check using your hand
that the grinding wheel movement is true and free.
If the grinding wheel is worn so much that the above clearance can no longer be achieved even after adjustment of the workpiece support
/or the eye shield mount , then the grinding wheel must be changed.
 COMMISSIONING
Ensure that the equipment is switched off and that the ON/ OFF switch is in the "0" position. Take note of the mains voltage. The voltage
must agree with that shown on the equipment rating plate (equipment shown as 230 V can also be connected to 220 V).
ON / OFF switch in position "1" = equipment runs at a constant speed
ON / OFF switch in position "0" = equipment is switched off
 USE
To grind metal tools or metal items, place the workpiece on the workpiece support /and slowly bring it close to the grinding wheel .
Carefully press the workpiece against the grinding wheel . Too much pressure can lead to overloading of the bench grinder. Grinding should
be carried out only on the circumference of the grinding wheels.


5



CHANGING A GRINDING WHEEL
Always make sure that the mains plug is out of the socket before doing any work on the equipment and when it is out of use.
You must only use grinding wheels on which the manufacturer's information, the type of adhesive, dimensions and permitted speed agree
with the technical information specified for this bench grinder.
Do not use any damaged or distorted grinding wheels. If you install new grinding wheels carryout a ringing test before use. Grinding wheels
in good condition give a clear ringing noise when struck lightly with a plastic hammer.
Take off the wheel guard cover , eye shield and the wheel edge cover , and slacken the workpiece mount /. You must ensure
that the left-hand side of the bench grinder (see Fig. 2) has a left-hand thread and the right-hand side has a right-hand thread. The notched
nut indicates the left-hand thread. The nut without notches corresponds to the right-hand thread. This ensures that the nuts can only
be screwed off in the direction of rotation of the spindle.
Now change the grinding wheels and reassemble all the components in the reverse order.
WARNING!
01. Do not interchange the flanges when attaching the grinding wheels (see Fig.2).
02. Use only the clamping flange supplied to mount the grinding wheels. Central fixing holes in grinding wheels are not to be redrilled.
03. Never operate the bench grinder without the wheel guard cover , eye shields or the wheel edge cover in place. Always fully
reassemble the grinder before use.
04. Check and correct the setting of the work piece supports /and eye shield mounts at frequent intervals (as described in the
Section "Positioning workpiece support and eye shields").
05. After changing a grinding wheel, the grinder must to be run for a test period under no load of at least 5 minutes. Ensure that there is
no one in the danger area.
CARE AND MAINTENANCE
Always make sure that the mains plug is out of the socket before doing any work on the equipment.
The PDS 150 Bench Grinder does not generally require maintenance.
Clean the bench grinder frequently. For best results, immediately after you have finished using it.
Do not allow any liquids to enter the bench grinder. Use a soft cloth to clean the grinder. Do not under any circumstances use petrol
or strong solvents.
Store the grinder in a dry room.
Repairs are only to be carried out at a specialist electrical repair centre. This electrical equipment complies with the relevant safety
regulations. Repairs may only be carried out by a specialist electrical repair centre using original spare parts, otherwise injury
could occur to the user.
You can find further practical tips on electrical tools in the accompanying booklet "Safety Advice".

6


STATEMENT OF CONFORMITY
We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare
that this product conforms with the following EC regulations:
EC machine guideline:
EC low voltage regulations:
Electromagnetic compatibility:
Applicable harmonised standards:
Manufacturer: PARKSIDE
Model type: PDS 150
Description: BENCH GRINDING MACHINE
Bochum, 31.07.2002
Hans Kompernaß
- Managing Director -
7

98/37 EEC
73/23 EEC (with change EC directive 93/68 EEC)
89/336 EEC (with change EC directive 93/68 EEC)
DIN VDE 0741/08.63
DIN 66069/06.73
VBG 7n/01.93
EN 61029-1:2000
PrEN 61029-2-4:1992
EN 55014-1:1993/A2:1999
EN 61000-3-2/1995/A2:1998
EN 55014-2:1997
EN 61000-3-3:1995



8
WARRANTY
This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of
care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its
original packaging with the proof of purchase (if available) to the closest service address.
Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty.
Beaver Electronic Services · The Lodge, Premier Business Park
Long Street, Walsall · West Midlands, WS2 9DY
Tel.: [phone] · Fax: [phone]
WARRANTY
This piece of equipment is covered by a 36-month warranty as of the date of purchase. The equipment was produced with the greatest of
care and underwent thorough testing before delivery. In the unlikely event of detecting a functional defect, please return the equipment in its
original packaging with the proof of purchase (if available) to the closest service address.
Damage caused due to improper handling as well as regular wear of the parts are not covered by this warranty.
Irish Web Specialists
1 Verbena Avenue · Dublin 13
Tel.: [phone] · Fax: [phone]

9

© manual design, photos, translations
by ORFGEN Marketing & Communication
Essen · Germany
www.orfgen-nm.de