Parkside 298657 User manual
TABLE SAW PTK 2000 D3
TISCHKREISSÄGE
Originalbetriebsanleitung
TABLE SAW
Translation of the original instructions
IAN 298657
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions
of the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
GB / IE / NI Translation of the original instructions Page 6DE / AT / CH Originalbetriebsanleitung Seite 19
1
2
4
3
1 2
2 3
18
14
9
11
24
21
22
23
3 4 5 6
15
11
13
14
9
8
7
16
10
a b c d ef
g
17
19
20
12
Bag A Bag B
12x 6x 6x 4x
g
12x8x
ce
h
i k
12
10
3
12
8
10
6
9
11
7
5
27
7
17
7
26
f
17
7
24
24
23
22 22
25
25
f
26
26
27
26
26
a
27
a
25
25
c e
c ef
b c d e
b c d e
21 2121
4
max. 3-5 mm
16
18
14
17
19
15
13
38
37
36
18
3
29
31
2
5
28
28
35
+
–
+
–
a
20
2
5
30
fc e
z
5
GB IE
6
NI
Introduction
Congratulations on the purchase of your new device. With it, you
have chosen a high quality product.
During production, this equipment has been checked for quality
equipment is therefore guaranteed.
contain important information on safety, use and disposal.
Before using the product, familiarise yourself with all of the oper-
ating and safety instructions. Use the product only as described
in the event that the product is passed on, hand over all docu-
ments to the third party.
Translation of the original
EC declaration of conformity .................................. 33
Content
Introduction ............................................................ 6
Intended purpose.................................................... 6
General description................................................. 7
Extent of the delivery .......................................................7
Overview.......................................................................7
Functional description......................................................8
Technical data......................................................... 8
Safety instructions................................................... 8
Symbols and icons ..........................................................8
Symbols on the appliance ................................................8
Graphical symbol additionally on the saw blades ...............8
Symbols in the manual.....................................................9
Safe operation................................................................9
Additional safety instructions ..........................................10
Safety instructions for handling saw blades ......................10
..............11
Safety Instructions for Handling the Laser .........................11
Safety Instructions for Handling Batteries ........................11
Residual Risks ...............................................................11
Electrical Connection.....................................................11
Important Instructions.....................................................12
Faulty Electrical Connection Cable .................................12
Alternating Current Motor ..............................................12
Assembly.............................................................. 12
Assembling the frame and table width extender with length
extender ......................................................................12
....12
Mounting / dismounting the Saw Blade Guard ................13
...............................................13
Attaching/changing the Saw Blade.................................13
Connect the suction device.............................................13
Before putting into operation ..........................................13
Operation ............................................................. 14
Switching on and off .....................................................14
Adjusting the Cutting Depth............................................14
........................................14
Adjusting the Stop Height .............................................14
......................................................14
Adjusting the Cutting Width .........................................14
Adjusting the Stop Length...............................................14
............................................14
.............................................................14
............................14
Angle Adjustment..........................................................15
Adjusting the Laser .......................................................15
Using the Laser ............................................................15
Use ...................................................................... 15
.........................................15
Cutting narrow Workpieces ..........................................15
Cutting very narrow Workpieces.....................................15
....................................................16
.............................................16
Cutting Chipboard ........................................................16
Collection bag for wood residues....................................16
.....................................................................16
Cleaning and Servicing.......................................... 16
Cleaning......................................................................16
Storage................................................................. 16
Waste disposal and environmental protection ....... 16
Trouble shooting ................................................... 17
Spare parts/Accessories........................................ 17
Guarantee ............................................................ 17
Repair Service....................................................... 18
Service-Center....................................................... 18
Importer ............................................................... 18
Intended purpose
-
hwise and crosswise (only with the transverse stop), depending
on the machine size. All types of round timbers must not be cut
Any other use beyond that is considered to be not in accordance
types of resulting damage or injury and not the manufacturer.
-
table for the machine (HM or CV saw blades).
prohibited. Use in accordance with the designated purpose is
also deemed to include observance of the safety instructions, as
well as the assembly and operating instructions in the operating
manual.Individuals who operate and maintain the machine must
be familiar with it and must have been instructed in possible ha-
zards. Moreover, the latest accident prevention regulations must
-
onal health and safety technology must be complied with.
IE NI
7
GB
Caution! When using equipment, certain safety precautions
must be complied with in order to avoid injuries and damage.
You should therefore read these operating instructions / safety
-
mation is available to you at all times. Should you give the de-
vice to anyone else, please give them these operating instructions
/ safety instructions as well. We assume no liability for accidents
or damage caused by failure to observe these instructions or the
safety instructions. Changes to the machine will cause the ma-
nufacturer‘s liability with respect to any resulting damage to be
completely excluded. Even when the device is used in accordan-
ce with the designated purpose, it is nevertheless not possible to
completely eliminate certain residual risk factors. Due to the de-
sign and structure of the machine, the following risks may occur:
-
• Reaching into the running saw blade (cuts)
• Saw blade breaks.
• Ejection of faulty hard metal parts of the saw blade.
• Hearing damage if the necessary hearing protection is not used.
• Emissions of wood dust which are harmful to the health when
used in closed rooms.
-
gnated purpose does not include commercial, handicraft or industrial
applications. We assume no warranty if the device is used in commer-
cial, handicraft or industrial businesses or for equivalent purposes.
General description
Extent of the delivery
Carefully unpack the appliance and check that it is complete:
- Saw table with pre-assembled
carbide-tipped saw blade with 24 teeth
carbide-tipped saw blade with 48 teeth
(additionally enclosed)
- Blade guard
- Riving knife with laser
- Batteries 1.5V AAA (2x)
- Stop rail
- Legs (4x)
- Central struts (4x)
- Rubber feet (4x)
- Stand brackets (2x)
- Instruction for use
Mounting Material
- Bag A for base frame, centre struts and stand brackets:
(e) Nuts, 12 pieces
- Bag B for table length/width extension and collection bag:
(g) Carriage bolt, small with two nuts, 4 pieces
Tools
- (h) Hexagon socket wrench HX 6
- (k) Ring spanner AF 10/22
- (i) Open-ended spanner AF 8/10
Additional tools required
.
Overview
11 Saw table
2 Saw blade guard
3 Riving knife (not visible)
4 Saw blade (not visible)
8 Cam lever
9 Locking handle
10 Scale
11 Handwheel
12 Crank handle
13 Base frame
14 On/off switch
15 Collection bag for wood residues
16 Guide rail
218 Suction adapter
20 Bracket for saw blade storage
421 Legs (4x)
22 Central struts (4x)
23 Rubber feet (4x)
24 Stand brackets (2x)
525 Attachment points
10
16 28 Countersunk screws of the table insert
17 29 Fixing screws of the riving knife
18 30 Slot in the riving knife
GB IE
8
NI
19
26 32 Cam lever
33 Groove
31 35 Laser
36 Laser switch
32 37 Screw for battery compartment
38 Battery cover
37
39 Stop rail
Functional description
-
hwise and crosswise (only with the transverse stop), depending
on the machine size. All types of round timbers must not be cut
with it.
Technical data
Bench circular saw.............................................................. PTK 2000 D3
AC motor......................................................... 230 V~ 50Hz
...................................................................2000 Watt
Operating mode ...................................................... S6 40%*
Safety class ..................................................................... II
..........................................................
Idling speed ..........................................................4800 min-1
Carbide saw blade ..............................ø 254 x ø 30 x 2.8 mm
Idling speed saw blade, n max. ..............................7000 min-1
Number of teeth.........................................................24 / 48
...................................................2.5 mm
min. Workpiece size WxLxH ............................... 10x50x1 mm
........................................................630 x 445 mm
...........................620 x 250 mm
.................................435 x 320 mm
Cutting height max. 90°................................................73 mm
Cutting height max. 45°................................................63 mm
Height adjustment ...................................................0 - 73 mm
Saw blade, swivelling...................................................0 - 45°
Extraction connection.................................................ø 34 mm
Weight (including accessories),
..................................................................... approx 21.5 kg
Laser class...........................................................................2
Laser wavelength ....................................................... 650 nm
Laser power ............................................................. < 1 mW
Laser module power supply
........................................................... 2 x 1.5 V Micro (AAA)
Sound pressure level
(LpA)..................................................pA = 3 dB
Sound power level (LWA)
measured......................................... WA = 3 dB
guaranteed .........................................................108 dB(A)
* Operating mode S6 40%: Continuous operation with intermittent load
(cycle time 10 min). In order not to heat the motor more than permitted,
the motor may only be operated for 40% of the cycle time with the stated
nominal power and must then continue running for 60% of the cycle time
without a load.
of further development without notice. All dimensions, references
and information in this instruction manual are therefore not guar-
anteed. Legal claims made on the basis of the instruction manual
can therefore not be considered as valid.
Safety instructions
CAUTION!-
served while using electric tools to protect against electric shock,
this electric tool and keep the safety instructions in a safe place.
Symbols and icons
Symbols on the appliance:
Carefully read these Operating Instructions.
Wear eye protection.
Wear ear protection.
Wear breathing protection.
Caution - Risk of injury.
Never reach into the running blade.
wet, nor should it be operated in a moist environment.
Caution! - Laser radiation. Do not look into the beam.
Laser class 2
108
Information of the acoustic power level LWA in dB.
Safety class II (Double Isolated)
Electrical appliances must not be disposed of with the
domestic waste.
Graphical symbol additionally on the saw
blades
Caution - a damaged blade must not be used under any
circumstances. Replace the saw blade immediately.
29
IE NI
9
GB
Symbols in the manual
Warning symbols with information on damage
and injury prevention.
Instruction symbols (the instruction is explained at the
place of the exclamation mark) with information on
preventing damage.
Help symbols with information on improving tool
handling.
Hazard symbol with information on the prevention of per-
sonal injury caused by electric shock..
Warning! Electric shock hazard.
Always unplug the device before working on it.
Safe operation
1 Keep work area clear.
– Cluttered areas and benches invite injuries.
2 Consider work area
environment.
– Do not expose tools to rain.
– Do not use tools in damp or wet locations.
gases.
3 Guard against electric shock
– Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
4 Keep other persons away!
– Do not let persons, especially children, not involved in
the work touch the tool or the extension cord and keep
them away from the work area.
5 Store idle tools
– When not in use, tools should be stored in a dry lo-
cked-up place, out of the reach of children.
6 Do not force the tool.
– It will do the job better and safer at the rate for which it
was intended.
7 Use the right tool.
– Do not force small tools to do the job of a heavy tool.
– Do not use the power tool for such purposes for which it
is not intended. Use for example no circular saws to cut
tree branches or logs.
8 Dress properly.
– Do not wear loose clothing or jewellery, they can be
caught in moving parts.
– Non-skid footwear is recommended when working out-
doors.
– Wear protective hair covering to contain long hair.
9 Use protective equipment.
– Use safety glasses.
– Use face or dust mask if working operations create dust.
10 Connect dust extraction
equipment
– If the tool is provided for the connection of dust extraction
and collecting equipment, ensure these are connected
and properly used.
– Indoor operation is permitted only with a suitable extracti-
on system.
11 Do not abuse the cord.
– Never yank the cord do disconnect it from the socket.
12 Secure work.
– For long workpieces, an additional supporting surface
(table, trestles, etc.) is required in order to prevent tipping
of the machine.
surface and stop in order to prevent wobbling or twisting
of the workpiece.
13 Do not overreach
– Avoid awkward hand positions in which one or both
hands could touch the saw blade as the result of a sud-
den slip.
14 Maintain tools with care
performance.
– Follow instruction for lubricating and changing accessories.
– Inspect tool cords periodically and if damaged have
them repaired by an authorized service facility.
– Inspect extension cords periodically and replace if dama-
ged.
15 Disconnect tools.
– Never remove loose splinters, chips or jammed pieces of
wood when the saw blade is running.
– When the electric tool is not in use, before maintenance
and when changing tools such as the saw blade, drill bit,
milling cutter.
16 Remove adjusting keys and wrenches
– Form the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
17 Avoid unintentional starting.
– Ensure switch is in “off” position when plugging in.
18 Use outdoor extension leads.
– When the tool is used outdoors, use only extension cords
intended for outdoor use and so marked.
– Use the cable drum only in the unrolled state.
19 Stay alert.
Watch what you are doing, use common sense and do not
operate the tool when you are tired.
20 Check damaged parts.
– Before further use of tool, it should be carefully checked
to determine that it will operate properly and perform its
intended function.
– Check whether the moving parts are working properly and
are not becoming jammed or whether parts are damaged.
to ensure the proper operation of the power tool.
– A guard or other part that is damaged should be proper-
ly repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual.
– Have defective switches replaced by an authorized ser-
vice centre.
– Do not use any faulty or damaged connection cables.
– Do not use the tool if the switch does not turn it on and off.
GB IE
10
NI
21 Warning!
recommended in this instruction manual may present a
risk of personal injury.
using original spare parts, otherwise this may result in
considerable danger to the user.
Additional safety instructions
1 Safety Precautions
– Warning! Do not use damaged, cracked or deformed
saw blades.
– Replace a worn table insert. Regrinding is not allowed.
– Only use saw blades recommended by the manufacturer
which conform to EN 847-1. Warning! When changing
the saw blade ensure that the cutting width is not smaller
and the main blade thickness of the saw blade not grea-
ter than the thickness of the riving knife!
– Make sure that a saw blade is selected which is appro-
priate for the material to be cut.
-
cludes: Hearing protection to reduce the risk of becoming
hard of hearing, breathing respirator to reduce the risk of
inhaling hazardous dust.
- Wear gloves when handling saw blades and rough mate-
rials.
- Whenever practicable, saw blades should be carried in
a container.
– Wear safety goggles. Any splinters, chips and dusts
which are ejected from the device when it is in operation
may cause sight loss.
– Connect the power tool to a dust collection device when
sawing wood. Among other things, the emission of dust
is affected by the type of material to be machined, the
importance of local deposition (capture or source) and
-
chanisms.
- Do not use any saw blades made of high-alloy high-
speed steel (HSS).
– Always store the push stick or push block in its holder on
the power tool when not in use.
2 Maintenance and Servicing
– Always remove the mains plug when carrying out any
adjustments or maintenance work.
-
cluding the properties of the blades, the condition of the
saw blade and power tool. If possible, use saw blades
that are designed to reduce the noise level, service the
power tool and tool attachments regularly and repair
them if necessary to reduce noise.
- Report any faults to the power tool, safety devices or the
tool attachment as soon as they are discovered to the
person responsible for safety.
3 Safe Working
– Use the push stick or the handle with push block to pass
the workpiece safely past the saw blade.
– Make sure that the riving knife is always used and that
this is correctly adjusted.
– Use the upper blade guard and adjust it correctly.
– Use only saw blades whose maximum speed is not lower
than the maximum spindle speed of the tool being used
and which are suitable for the material to be cut.
– Do not create any rebates or grooves unless a suitable
protective device, such as a tunnel guard, is attached
above the saw table.
– Circular saws must not be used for slotting (cutting
grooves which end in the workpiece).
– When transporting the power tool, use only the transport
devices supplied. Never use the guards for handling or
transporting the tool.
- During transport, make sure that the top part of the saw
blade is covered, for example with the guard.
– Ensure that the only spacer washers and spindle rings
which are used are suitable for the purpose stated by the
manufacturer.
of loose particles such as chips and cutting residues.
– Working position always to the side of the saw blade.
– Do not remove any cutting residues or other parts of the
workpiece from the cutting area for as long as the ma-
chine is running and the sawing unit is not yet in the rest
position.
– Secure long workpieces against tilting at the end of the
cutting operation (e.g. unwinding stand or roller stand).
– Caution! long workpieces against tilting at the end
of the cutting operation (e.g. unwinding stand or roller
stand).
– Caution! Never remove any loose splinters, chips or jam-
med pieces of wood when the saw blade is still running.
• Always switch off the machine and remove the plug
before repairing any faults or removing jammed pieces
of wood.
• Always switch off the motor and remove the plug before
carrying out any conversions or adjustment, measurement
and cleaning work.
• Before switching on, check that the spanners and adjust-
ment tools have been removed.
Warning! During operation, this power tool produces an elec-
negatively affect active or passive medical implants. In order to
reduce the danger of serious or fatal injuries, we recommend
that individuals who wear medical implants should consult their
doctor and the manufacturer of the implant before operating the
power tool.
Safety instructions
for handling saw blades
1 Only use tools which you know how to handle.
3 Note the direction of rotation of the motor and saw blade.
4 Circular saw blades with cracks in them must be taken out of
service (repair is not permitted).
7 Handle the tools used with care. It is best to store these in
their original packaging or special containers. Always wear
protective gloves to improve your grip and further reduce the
IE NI
11
GB
risk of injury.
8 Before using any of the tools, ensure that all protective de-
vices are correctly attached.
technical requirements of this power tool and are properly
attached.
wood and never for working metal.
Assembly and Attachment
of Tools and Tool Parts
they cannot become loose during operation.
b) Attachment bolts and nuts are to be tightened to the torques
c) Extending a spanner or tightening with the help of hammer
blows is not permitted.
grease, oil and water.
manufacturer‘s instructions.
f) In order to adjust the borehole diameter of circular saw
inserted rings, e.g. rings which have been pressed into place
or which are held in place by means of an adhesive bond,
one another.
Safety Instructions
for Handling the Laser
– Caution: Laser radiation - Do not look into the beam - Laser
class 2
–
laser (34).
Safety Instructions
for Handling Batteries
1 Ensure at all times that the batteries are inserted with the
correct polarity (+ and –), as shown on the battery itself.
2 Do not short-circuit the batteries.
3 Do not charge up rechargeable batteries.
4 Do not overcharge the battery!
5 Do not mix old and new batteries or batteries of a different
type or from different manufacturers! Replace all batteries of
a set at the same time.
6 Remove used batteries immediately out of the device and
dispose of them correctly!
7 Do not heat the batteries!
8 Do not carry out any welding or soldering work directly to
the batteries!
9 Do not take the batteries apart!
10 Do not deform the batteries!
12 Store the batteries out of the reach of children.
13 Do not allow children to replace the batteries without supervi-
sion!
sources of heat. Do not place the battery in direct sunlight
and do not use or store it in motor vehicles in hot weather.
15 Store used batteries in the original packaging and keep them
away from metal objects. Do not mix (up) unpacked batte-
ries! Otherwise this may cause the battery to short-circuit,
16 Remove batteries from the device if this is not going to be
used for a prolonged period, unless it is to be used in emer-
gencies!
17 NEVER touch batteries which have leaked without appro-
priate protection. If the leaked liquid comes into contact with
the skin, you should rinse off this area of the skin immedia-
tely under running water. Make sure at all events that your
eyes and mouth do not come into contact with the liquid. If
they do, seek medical advice immediately.
18 Clean the battery contacts and the equivalent contacts in the
device before inserting the batteries.
Residual Risks
This power tool has been constructed in accordance
with the latest technology and the generally recog-
nised safety regulations. Nevertheless, it is possible
that individual residual risks may occur during opera-
tion.
• Electrical hazard if improper electrical connection cables are
used.
• In addition, concealed residual risks may be present in spite
of all the precautions that have been taken.
• Residual risks can be minimised by observing the „Safety
instructions“ and „Use in accordance with the designated
purpose“, as well as the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
the machine, as well as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when inserting
the plug into the socket, the power button must not be pressed.
ensure the optimal performance of your saw.
machine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.
Electrical Connection
The installed electric motor is connected ready for
operation. The connection complies with the relevant
VDE and DIN regulations. The customer‘s network
connection and any extension cable used must com-
ply with these regulations.
•
its use at freely selectable connection points is not permitted.
• If the network conditions are unfavourable, the device may
•
connection point of 0.107 ohm must not be exceeded.
• As the user, you must ensure – in consultation with your
electricity supply company if necessary – that the continuous
current carrying capacity of the network at the connection
GB IE
12
NI
the product.
Important Instructions
If the motor is overloaded, it switches itself off automatically.
After cooling down (times vary), the motor can be switched on
again.
Faulty Electrical Connection Cable
Insulation damage often occurs to electrical connection cables.
•
windows or door gaps.
•
connection cable.
• Cut surfaces caused by vehicles driving over the connection
cable.
• Insulation damage caused by tearing out of the wall socket.
• Cracks resulting from the insulation becoming old.
Such faulty electrical connections must not be used and may
endanger life due to the damage to the insulation.
Electrical connection cables should be checked regularly for
damage. Ensure that during such checks, the connection cable is
not connected to the mains.
Electrical connection cables must comply with the relevant VDE
and DIN regulations. Only use connection cables with the mar-
king H05VV-F.
It is stipulated by law that the type of connection cable must be
printed on it.
Alternating Current Motor
•
• Extension cables up to 25 m in length must have a cross-sec-
tion of 2.5 mm².
Connections and repairs to the electrical equipment may only be
please provide the following information:
• Current type of the engine
• Data from the machine type plate
• Data from the motor type plate
Assembly
Assembly, Replacement of Parts and Adjustments
Caution! The mains plug must be removed before all
servicing, retooling and assembly work.
the parts which are similar.
Note: If connections are secured with a bolt (round head/or
hexagonal), hexagonal nuts and a washer, the washer must be
placed under the nut.
Insert the bolts from the outside to the inside in each case, secu-
ring the connections with nuts from the inside.
Note:
extent that they cannot fall off.
Assembling the frame and table width
extender with length extender
(Figures. 4-13)
2. Insert the four legs (21) at the corner positions into the device
housing. Do not place any screws yet.
3. Now loosely screw the central struts (22) onto the legs (21).
Use the carriage bolts (b), the washers (c), the spring was-
hers (d) and the nuts (e) (Fig. 7).
4. Screw the stand brackets (21) into the rear legs using the
drill holes. Assembly material for each: 2 carriage bolts (b),
the washers (c), the spring washers (d) and the nuts (e)
(Fig. 9). Caution! Both stand brackets must be
attached to the rear of the machine at attachment
points 25! (Abb. 5).
5. Loosely tighten the table width extender (7) and table length
extender (17) on the saw table (1) using the hexagon bolts
table extensions (7) points away from the saw table (1).
6. Loosely tighten the table supports (26, 27) on the housing of
the table circular saw. Use the hexagonal bolts with collar
(a) from bag A. Use the table width extender (7)/table
length extender (17), hexagonal bolts (f), washers (c) and
widening extension, the long supports (27) are for the length
extension, (Fig. 12, 13). Screw the four legs (21) and
the table supports (26, 27) onto the housing.
7.
table.
8. Next, tighten all the screws of the legs (21) and the table
width extender (7)/table length extender (17).
9. Now attach the rubber feet (23) to the legs (21) (Figure 8).
10. .
11. Screw one nut on each of the screws (g). Screw the four
screws with pre-mounted nuts onto the side of the table width
these with four additional nuts. Suspend the collection bag
for wood residues (15) onto the four screws.
Mounting / adjusting the Riving Knife
Insert the battery (Figures 15-20)
Caution! Remove the mains plug! The setting of the
saw blade (4) must be checked whenever a blade has
been replaced.
1. Inserting the batteries (Figure 15):
- Remove the battery compartment cover (38) by loosening the
screw (37). Now remove the battery compartment cover (38)
by bending at the side.
- Insert the batteries supplied (type AAA), ensuring the correct
polarity (see Figure 15).
tighten it with the screw (37). Notes concerning the batteries:
- If you are not going to use the laser for a prolonged period,
please remove the batteries from the battery compartment.
IE NI
13
GB
device.
- Do not place the batteries on radiators or expose them for a
45 ° could damage the device.
2. Initial mounting of the laser module:
Fig. 15.
(Figures 16-20)
3. Adjust the saw blade (4) to a max. cutting depth, move to
the 0° position and lock in place.
4. Dismantle the saw blade guard (2)
(not during initial assembly).
5. Release the two attachment bolts (28) and remove the table
insert.
AF8 supplied).
should be between 3 mm and max. 5 mm, (Figure 18).
9. Retighten the attachment bolts (29) and mount the table insert
(5).
10. Reattach the saw blade guard (2).
Mounting / dismounting
the Saw Blade Guard
(Figures 19)
-
de protection has already been carried out in
the previous assembly step.
1. Loosen the knurled nut and wing nut (31) of the saw blade
the riving knife (3).
2. Mount the bolt with the knurled nut and washer (31) so that
be able to move freely.
4. Dismantling is carried out in reverse order. Caution! Before
you start sawing, the saw blade guard (2) has to be lowered
onto the item being sawn.
Replacing the Table Insert
(Figures 16 and 20)
1. If it is worn or damaged, the table insert (5) has to be repla-
ced, as otherwise there is an increased risk of injury.
2. Remove the 2 countersunk screws (28).
reverse order.
Attaching/changing the Saw Blade
(Figure 21)
1. Caution! Remove the mains plug and wear protec-
tive gloves.
2. Dismantle the saw blade guard (2).
3. Remove the table insert (5) by releasing the two countersunk
screws (28).
4.
jaw spanner (k) (SW 22) to stop the motor spindle from turning.
5. Caution!
blade. Remove the loosened screw.
before attaching the new saw blade.
8. Insert and tighten the new saw blade in reverse order.
Caution! Note the direction of motion; the slope of
the cutting edge of the teeth must face the directi-
on of motion, i.e. forwards (see the arrow on the
saw blade guard.
9. Reattach and adjust the table insert (5) and the saw blade
guard (2).
10. Before you work with the saw again, a check must be
carried out to ensure that the protective devices are working
properly.
Connect the suction device
(Fig. 14)
1. Attach a suction hose to the suction adapter (18). If
necessary, secure the suction hose with a hose clamp to
prevent it from slipping off the suction adapter (18).
2. A household vacuum cleaner is not suitable as a suction de-
vice. Use a multi-purpose vacuum cleaner or a swarf extracti-
on machine.
Before putting into operation
base or similar item. For this, use the drill holes which are
located in the frame of the machine. For safe use on a work
bench, four mounted rubber feet are provided
• Before the machine is put into operation, all covers and safety
devices must be properly attached.
• In the case of wood which has already been worked with,
check for foreign bodies such as nails or screws etc.
• Before pressing the on/off switch, make sure that the saw bla-
de is correctly attached and that moving parts are free-running.
• Before connecting the machine, check that the data on the
type plate matches those of the mains system.
safety socket which is protected by a fuse of at least 16A.
• If possible, connect the device only to a socket with a residual
current circuit breaker (RCCB) with a tripping current of not
more than 30 mA.
GB IE
14
NI
Operation
Switching on and off
(Figure 3)
-
ton „I“. Before you start sawing, wait until the saw blade has
reached its maximum speed.
- In order to switch the saw off again, the red pushbutton „0“
has to be pressed.
Adjusting the Cutting Depth
(Figure 3)
By turning the crank handle (12), the saw blade can be set to the
desired cutting depth (continuous).
- Clockwise: increases the cutting depth
- Anticlockwise: reduces the cutting depth
Adjust the saw blade so that it protrudes approximately 5
mm above the material to be cut. Check the adjustment by
means of a test cut.
Working with the Parallel Stop
Adjusting the Stop Height
(Figures 22 and 24)
surfaces at different heights.
- Depending on the thickness of the materials to be cut, the
stop rail (39) has to be used differently. For thin material
(workpiece thickness less than 25 mm), use Figure 22. For
thick material (workpiece thickness more than 25 mm), use
Figure 24.
Turning the Stop Rail
(Figures 22-24)
nuts (m).
- Now the stop rail (39) can be pulled off the guide rail (16)
and pushed back over it again with the groove.
Adjusting the Cutting Width
(Figures 25-26)
- When wooden pieces are being cut lengthwise, the parallel
stop (6) has to be used.
of the saw blade (4).
- Insert the parallel stop into the side of the guide rail (16)
(Figure 26).
- On the guide rail for the parallel stop (6) there are 2 scales
and saw blade (4) (Figure 25).
- Select the suitable scale according to whether the stop rail
(39) has been turned around for working with thick or thin
material:
High stop rail (thick material): scale (o)
Low stop rail (thin material): scale (n)
- Adjust the parallel stop (6) to the desired level on the sight
Adjusting the Stop Length
(Figure 27)
- In order to prevent the material being cut from jamming, the
stop rail (39) can be moved in the longitudinal direction.
- Rule of thumb: the rear end of the stop abuts on an imagi-
and runs towards the back at an angle of 45°.
- Adjust the required cutting width.
- Release the knurled nuts (m) and push the stop rail (39)
forward until the imaginary 45° line is touched.
Adjusting the Parallel Stop
(Figure 28)
- Caution! Remove the guard.
- Adjust the saw blade (4) to the maximum cutting depth.
- Adjust the parallel stop (6) such that the stop rail (39)
touches the saw blade (adjustment for thick material.
- If the parallel stop (6) is not parallel to the saw blade (4),
please proceed as follows. Release the screws (r) on the
parallel stop until the parallel stop (6) can be aligned to be
parallel with the saw blade (4) (Figure 28).
- Retighten the screws (r).
Transverse stop
(Figure 29)
- When the wood is being cut to size, the transverse stop (40)
must be extended with the stop rail (39) of the parallel stop
(6) (Figure 29)
table.
- Loosen the knurled screw (34).
set.
- Retighten the knurled screw (34).
- In order to extend the transverse stop (40) with the stop rail
(39), the stop rail (39) has to be removed from the parallel
stop (6). Now the stop rail has to be mounted as shown in
Caution!
- Do not push the stop rail (39) too far in the direction of the
saw blade.
should be approximately 2 cm.
Adjusting the scale of the parallel stop
(Figure 30)
- Check whether the display on the sight glass (p) of the
parallel stop (6) shows the correct values with respect to the
cutting line. If this is not the case, please proceed as follows:
- Release the screw (q) with which the display on the sight
(p) display can now be set to the correct position.
- Now, retighten screw (q) on the sight glass (p).
IE NI
15
GB
Angle Adjustment
(Figure 29 and 3)
With the table circular saw it is possible to make bevel cuts to
the left at an angle of 0° to 45° to the stop rail. Before each cut,
make sure that no collision is possible between the stop rail (39),
cross-cutting gauge and the saw blade (4).
- Release the locking handle (9)
scale (10).
- Lock the locking handle (9) in the desired angular position.
Adjusting the Laser
(Figure 32)
If the laser (35) no longer shows the correct cutting line, this can
so that the laser beam hits the cutting teeth of the saw blade (4).
Using the Laser
(Figures 31-32)
your circular saw.
emitted through the laser exit aperture. You can then use the
line as an optical marking for the cutting line of the precision
- Insert the batteries
- Switch on the laser: turn the laser on/off switch (36) to I.
When the saw blade guard (2) is mounted, the laser on/off
switch (36) is accessible through a recess in the guard (Fi-
gure 31). A red laser beam is now projected out of the laser
exit aperture. If you guide the laser beam along the cutting
line mark while sawing, you will achieve clean cuts.
- Switch the laser off: turn the laser on/off switch (36) to 0.
when it is not required in order to save the batteries.
You should therefore remove these particles from the laser
exit aperture after every use (with the device switched off).
Use
Working Instructions
After each new adjustment, we recommend a trial cut in order to
check the set dimensions. After the saw has been switched on,
wait until the saw blade has reached its maximum speed before
you carry out the cut.
Secure long workpieces against tilting at the end of the cutting
process (e.g. unwinding stand etc.)
Caution with incision cutting.
Operate the device only with a suction system. Check and clean
the suction channels regularly.
Suitability of the saw blades:
- 24 teeth: soft materials, high chip removal, rough cut image
Performing Longitudinal Cuts
(Figure 33)
Here, a workpiece is cut in its longitudinal direction. One edge
of the workpiece is pressed against the parallel stop (6) while the
-
ring longitudinal cutting must never be in a straight line with the
cutting line.
- Adjust the parallel stop (6) according to the workpiece height
and the desired width.
- Switch on the saw.
workpiece and push the workpiece along the parallel stop
(6) into the saw blade (4).
- Guide from the side with your left or right hand (depending
on the position of the parallel stop) only up to the front edge
of the saw blade guard (2).
- Always push the workpiece through to the end of the riving
knife (3).
blade (4) is back in its resting position.
- Secure long workpieces against tilting at the end of the
cutting process! (e.g. unwinding stand etc.)
Cutting narrow Workpieces
(Figure 34)
Longitudinal cuts of workpieces with a width of less than 120
push stick is included in the scope of delivery. Replace a worn or
damaged push immediately.
• Adjust the parallel stop according to the planned workpiece
width.
• Advance the workpiece with both hands, making sure that
you use a push stick (19) as a pushing aid in the vicinity of
the saw blade.
• Always push the workpiece through to the end of the riving
knife.
Caution! In the case of short workpieces, the push
stick should be used from the beginning of the cutting
process.
Cutting very narrow Workpieces
(Figure 35)
For longitudinal cuts of very narrow workpieces with a width of
no push block included in the scope of delivery! (Available from
specialist shops) Replace a worn push block as soon as possible.
the workpiece.
and push the workpiece with the push stick (19) through to
the end of the riving knife.
GB IE
16
NI
Performing Bevel Cuts
(Figure 36)
All bevel cuts are made using the parallel stop (6).
- Adjust the saw blade (4) to the desired angle.
- Adjust the parallel stop (6) according to the workpiece width
and height.
Performing Transverse Cuts
(Figures 29, 37)
groove (33) is to be used if the saw blade (4) also has to be
positioned at an oblique angle.
coming into contact with the saw blade guard.
- Use the stop rail (39).
- Switch on the saw.
of the saw blade in order to perform the cut.
the free workpiece which is cut off.
- Always push the transverse stop (40) so far forwards until the
workpiece is completely cut through.
- Switch the saw off again. Only remove sawing waste when
the saw blade has come to a standstill.
Cutting Chipboard
In order to prevent the cut edges chipping when the chipboard
is cut, the saw blade (4) should be adjusted so that it is not more
than 5 mm above the thickness of the workpiece.
Collection bag for wood residues
can be collected directly from the saw table to keep it clean and
free from obstructions. Under no circumstances may the wood
residues in the collection bag protrude beyond the collection bag
Transport
(Fig. 38/39)
1. -
nect it from the power supply.
2.
suction adapter (18).
3. Insert the saw blade with the help of the crank handle (12).
By turning the saw blade (4) anticlockwise, it moves
downwards.
4. At least two people should carry the power tool. Do not hold
the points as shown in (Fig. 38/39) to transport the
machine.
5. -
tions, e.g. when it is transported in motor vehicles.
6. Secure the power tool against tilting and sliding.
7. Never use the protective devices for handling or transport.
Cleaning and Servicing
Remove the mains plug before carrying out any adjust-
ments, maintenance or repair work.
You should have any repair and maintenance work that is
not described in these instructions carried out by our Ser-
vice Centre. Only use original parts.
Cleaning
The device must not be sprayed with water or
placed in water. Otherwise there is a risk of
electric shock.
of dust and dirt as possible. Wipe the device off with a clean
cloth or blow it out with compressed air at a low pressure.
• We recommend that you clean the device immediately after
every use.
• Clean the device regularly with a damp cloth and some soft
the plastic parts of the device. Make sure that no water can get
into the interior of the device.
• Oil the moving parts once a month in order to extend the tool
life. Do not oil the motor.
Storage
• Store the appliance in a dry place well out of reach of
children.
Waste disposal and environmental
protection
-
teries, accessories and packaging in an environmentally friendly
manner.
Electrical machines do not belong with domestic waste.
• Dispose of the batteries according to local standards. Hand
in the batteries at a used battery collection point where they
are recycled in an environmentally friendly manner. For more
information, please contact your local waste management
provider or our service centre.
• Defective units returned to us will be disposed of for free.
IE NI
17
GB
1. Blade dissolves after swit-
ching off the engine
2. Engine will not start a) Failure mains fuse a) Check mains fuse
b) Defective extension cable b) Replace extension cord
c) Connections on motor or switch not in order c) Repair by electrical specialist
d) Motor or switch faulty d) Repair by electrical specialist
3. Motor wrong direction of
rotation a) Capacitor faulty a) Repair by electrical specialist
b) Wrong connection b) Exchange polarity of outlet by an
4. Motor will not work, the
fuse is activ a) Cross section of the extension cable does not
a) see „Electrical connection“
b) Overload by a blunt saw blade b) Change saw blade
5. Fire marks on the cutting
surface a) blunt saw blade a) Sharpen or change saw blade
b) wrong saw blade b) Change saw blade
Problem Possible cause Fault correction
Trouble shooting
Spare parts/Accessories
Spare parts and accessories can be obtained at
www.grizzly-service.eu
order number mentioned below ready.
(6) ....................... Order-No. 9110353 0
(40) ............................... Order-No. 9110 3531
(2) Blade guard, complete....................... Order-No. 9110 4 56 3
(17) ....................... Order-No. 9110 4 55 7
(5) ....................................... Order-No. 9110 4 56 6
(7) ................ Order-No. 9110 4 561
(7) ................... Order-No. 9110 4 562
(35) Laser.............................................. Order-No. 9110 4 558
(3) Riving knife....................................... Order-No. 9110 4 559
(11) Handwheel, complete ....................... Order-No. 91104560
(19) ........................................ Order-No. 9110 4950
(14) On/off switch, complete ................... Order-No. 9110 4952
(24) Stand brackets (both sides) ............... Order-No. 91103 542
(23) Rubber feet ..................................... Order-No. 91104951
(4) .......................... Order-No. 13800400
(4) ........................... Order-No. 13800401
(15) Collection bag................................. Order-No. 9110 4 55 6
Guarantee
Dear Customer,
of purchase.
In case of defects, you have statutory rights against the seller of
-
antee presented below.
Terms of Guarantee
purchase.
If a material or manufacturing defect occurs within three years of
the date of purchase of this product, we will repair or replace –
requires the defective equipment and proof of purchase to be pre-
sented within the three-year period with a brief written descrip-
tion of what constitutes the defect and when it occurred.
If the defect is covered by our guarantee, you will receive either
the repaired product or a new product. No new guarantee peri-
od begins on repair or replacement of the product.
Guarantee Period and Statutory Claims for Defects
and defects already present at the time of purchase must be re-
ported immediately after unpacking. Repairs arising after expiry
of the guarantee period are chargeable.
Guarantee Cover
strict quality guidelines and conscientiously checked prior to
delivery.
GB IE
18
NI
subject to normal wear and may therefore be considered as
breakable parts (e.g. switches, batteries, or parts made of glass).
proper use of the product. Intended uses and actions against
which the operating manual advises or warns must be categori-
cally avoided.
handling, use of force, or interventions not undertaken by our
authorised service branch.
Processing in Case of Guarantee
-
rections below:
(IAN 298657) ready as proof of purchase for all enquiries.
• Should functional errors or other defects occur, please initially
telephone
or by e-mail. You will then receive further information on the
processing of your complaint.
• After consultation with our customer service, a product re-
corded as defective can be sent postage paid to the service
address communicated to you, with the proof of purchase
when it occurred. In order to avoid acceptance problems
and additional costs, please be sure to use only the address
communicated to you. Ensure that the consignment is not sent
carriage forward or by bulky goods, express or other special
at the time of purchase and ensure adequate, safe transport
packaging.
Repair Service
For a charge, repairs not covered by the guarantee can
be carried out by our service branch, which will be happy to is-
sue a cost estimate for you.
We can handle only equipment that has been sent with adequate
packaging and postage.
Attention:
clean condition and with an indication of the defect.
Equipment sent carriage forward or by bulky goods, express or
other special freight will not be accepted.
We will dispose of your defective devices free of charge when
you send them to us.
Service-Center
GB Service Great Britain
(£ 0.10/Min.)
IAN 298657
IE
NI
Service Ireland
Northern Ireland
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
IAN 298657
Importer
Grizzly Tools GmbH & Co. KG
Stockstädter Straße 20
63762 Großostheim
Germany
www.grizzly-service.eu
AT CH
19
DE
Einleitung
haben sich damit für ein hochwertiges Gerät entschieden. Dieses
einer Endkontrolle unterzogen. Die Funktionsfähigkeit Ihres Ge-
rätes ist somit sichergestellt.
Die Betriebsanleitung ist Bestandteil dieses Gerätes. Sie ent-
hält wichtige Hinweise für Sicherheit, Gebrauch und Entsor-
gung. Machen Sie sich vor der Benutzung des Gerätes mit allen
Bedien- und Sicherheitshinweisen vertraut. Benutzen Sie das Gerät
nur wie beschrieben und für die angegebenen Einsatzbereiche.
Bewahren Sie die Betriebsanleitung gut auf und händigen Sie alle
Unterlagen bei Weitergabe des Gerätes an Dritte mit aus.
Bestimmungsgemäße Verwendung
-
Die Maschine darf nur nach ihrer Bestimmung verwendet werden.
Jede weitere darüberhinausgehende Verwendung ist nicht be-
stimmungsgemäß. Für daraus hervorgehende Schäden oder
Original EG-Konformitätserklärung ........................ 33
Inhalt
Einleitung............................................................... 19
Bestimmungsgemäße Verwendung ........................ 19
Allgemeine Beschreibung ....................................... 20
Lieferumfang.................................................................20
Übersicht......................................................................20
Funktionsbeschreibung ...................................................21
Technische Daten.................................................... 21
Sicherheitshinweise................................................ 21
Symbole und Bildzeichen ...............................................21
Sicheres Arbeiten ..........................................................22
Zusätzliche Sicherheitshinweise ......................................23
Sicherheitshinweise für den Umgang mit Sägeblättern........24
Montage und Befestigung von Werkzeugen und
Werkzeugteilen.............................................................24
Sicherheitshinweise zum Umgang mit dem Laser ...............24
Sicherheitshinweise zum Umgang mit Batterien ................24
Restrisiken.....................................................................25
Elektrischer Anschluss ....................................................25
Wichtige Hinweise ........................................................25
Schadhafte Elektro-Anschlussleitung ................................25
Wechselstrommotor ......................................................25
Montage ................................................................ 25
Montage Gestell und ..26
............26
Sägeblattschutz montieren / demontieren ........................26
................................................27
Montage/Wechsel des Sägeblattes .................................27
Absaugvorrichtung anschließen.......................................27
Vor der Inbetriebnahme..................................................27
Bedienung ............................................................. 27
Ein-, Ausschalten ..........................................................27
Einstellen der Schnitttiefe ................................................27
...................................27
..........................................27
Anschlagschiene drehen.................................................27
Einstellen der Schnittbreite .............................................28
Anschlaglänge einstellen ................................................28
......................................28
...............................................................28
........................28
Winkeleinstellung ..........................................................28
Justieren des Lasers .......................................................28
Benutzung des Lasers ....................................................28
Betrieb .................................................................. 29
Ausführen von Längsschnitten .........................................29
Schneiden schmaler Werkstücke .....................................29
Schneiden sehr schmaler Werkstücke...............................29
Ausführen von Schrägschnitten........................................29
.........................................29
Schneiden von Spanplatten.............................................30
Auffangsack für Holzreste...............................................30
.....................................................................30
Reinigung und Wartung ......................................... 30
Reinigung.....................................................................30
Lagerung ............................................................... 30
Entsorgung/ Umweltschutz..................................... 30
Fehlersuche............................................................ 31
Ersatzteile/Zubehör ............................................... 31
Garantie ................................................................ 32
Reparatur-Service .................................................. 32
Service-Center........................................................ 32
Importeur .............................................................. 32
Verletzungen aller Art haftet der Benutzer/Bediener und nicht
der Hersteller.
Es dürfen nur für die Maschine geeignete Sägeblätter (HM- oder
CV-Sägeblätter) verwendet werden.
Art ist untersagt. Bestandteil der bestimmungsgemäßen Verwen-
dung ist auch die Beachtung der Sicherheitshinweise, sowie der
Montageanleitung und Betriebshinweise in der Bedienungsanlei-
Darüber hinaus sind die geltenden Unfallverhütungsvorschriften
genauestens einzuhalten. Sonstige allgemeine Regeln in arbeits-
medizinischen und sicherheitstechnischen Bereichen sind zu
beachten.
Achtung!
Beim Benutzen von Geräten müssen einige Sicherheitsvorkeh-
rungen eingehalten werden um Verletzungen und Schäden zu
verhindern. Lesen Sie diese Originalbetriebsanleitung / Sicher-
heitshinweise deshalb sorgfältig durch. Bewahren Sie diese
gut auf, damit Ihnen die Informationen jederzeit zur Verfügung
sollten, händigen Sie diese Originalbetriebsanleitung / Sicher-
heitshinweise bitte mit aus. Wir übernehmen keine Haftung für
Unfälle oder Schäden, die durch Nichtbeachten dieser Anleitung
DE AT
20
CH
und den Sicherheitshinweisen entstehen. Veränderungen an der
Maschine schließen eine Haftung des Herstellers und daraus
-
• Berührung des Sägeblattes im nicht abgedeckten Sägebe-
reich.
• Eingreifen in das laufende Sägeblatt (Schnittverletzung)
• Rückschlag von Werkstücken und Werkstückteilen.
• Sägeblattbrüche.
• Herausschleudern von fehlerhaften Hartmetallteilen des Sä-
geblattes.
-
schutzes.
• Gesundheitsschädliche Emissionen von Holzstäuben bei Ver-
wendung in geschlossenen Räumen.
Bitte beachten Sie, dass unsere Geräte bestimmungsgemäß nicht
für den gewerblichen, handwerklichen oder industriellen Einsatz
konstruiert wurden. Wir übernehmen keine Gewährleistung,
wenn das Gerät in Gewerbe-, Handwerks- oder Industriebetrie-
Allgemeine Beschreibung
Lieferumfang
- Sägetisch mit vormontiertem
hartmetallbestückten Sägeblatt 24 Zähne
hartmetallbestücktes Sägeblatt 48 Zähne (zusätzlich beiliegend)
- Sägeblattschutz
- Spaltkeil mit Laser
- Batterien 1,5V AAA (2x)
- Anschlagschiene
- Schiebestock
- Standbeine (4x)
- Mittelstreben (4x)
- Gummifüße (4x)
- Standbügel (2x)
- Originalbetriebsanleitung
Montagematerial
- Beutel A für Untergestell, Mittelstreben und Standbügel:
(e) Muttern, 12 Stück
- Beutel B
(g) Schlossschraube, klein mit zwei Muttern, 4 Stück
Werkzeug
- (h) Innensechskantschlüssel HX 6
- (k) Ringschlüssel SW 10/22
- (i) Gabelschlüssel SW 8/10
Zusätzlich benötigtes Werkzeug
Die Abbildung der wichtigsten Funktionsteile
Übersicht
11 Sägetisch
2 Sägeblattschutz
3 Spaltkeil (nicht sichtbar)
4 Sägeblatt (nicht sichtbar)
8 Exzenterhebel
9 Feststellgriff
10 Skala
11 Handrad
13 Untergestell
14 Ein-, Ausschalter
15 Auffangsack für Holzreste
16 Führungsschiene
218 Absaugadapter
19 Schiebestock
20 Halterung zur Sägeblattaufbewahrung
421 Standbeine (4x)
22 Mittelstreben (4x)
23 Gummifüße (4x)
24 Standbügel (2x)
525 Befestigungspunkte
10
16
17 29 Befestigungsschraube Spaltkeil
18 30 Langloch im Spaltkeil
19 31 Rändelmutter mit Schraube
26 32 Exzenterhebel
This manual suits for next models
1
Table of contents
Languages:
Other Parkside Saw manuals
Parkside
Parkside PFS 710 E4 User manual
Parkside
Parkside PHKSZ 190 A1 User manual
Parkside
Parkside PDKS 120 - MANUAL 3 User manual
Parkside
Parkside PMTS 180 A1 User manual
Parkside
Parkside SABRE SAW PFS 710 A1 User manual
Parkside
Parkside PTS 480 A1 Quick start guide
Parkside
Parkside PMTS 210 A1 Quick guide
Parkside
Parkside PTS 500 A1 User manual
Parkside
Parkside PTS 500 B2 User manual
Parkside
Parkside PTS 500 A1 User manual
Parkside
Parkside PMTS 210 A1 Quick guide
Parkside
Parkside PHKS 1350 B2 User manual
Parkside
Parkside PTS 480 A1 Quick start guide
Parkside
Parkside PTSS 1200 A1 User manual
Parkside
Parkside PZKS 2000 B2 Quick guide
Parkside
Parkside PTK 1700 A1 User manual
Parkside
Parkside PHKS 1300 A1 User manual
Parkside
Parkside PZKS 2000 B2 Quick guide
Parkside
Parkside PHKSA 20-Li A2 User manual
Parkside
Parkside PTS 450 A1 User manual
Popular Saw manuals by other brands
Central Machinery
Central Machinery 94652 Assembly and operating instructions
Chicago Electric
Chicago Electric 91938 operating instructions
Villager
Villager VLN 1520 Original instruction manual
GMC
GMC 040521 ED8 PR instruction manual
Shop fox
Shop fox W1715 owner's manual
Meec tools
Meec tools 000841 operating instructions
