Partilink P4K-HUL4E1-P User manual

P4K-HUL4E1 4K UHD HDMI & USB Over IP Extender
P4K-HUL4E1-P 4K UDH HDMI & USB Over IP Extender with PoE
P4K-HRSUL4E1 / P4K- LHRSU1E4 P4K-HRSUL4E1-
P/ P4K-LHRSU1E4-P
Partilink Technology Co., Ltd Copyright @2017
User manual

Table of Contents
1. INTRODUCTION 3
2. FEATURES & APPLICATIONS 4
3. SPECIFICATION 5
4. HARDWARE DESCRIPTION 6
4.1 Transmitter 6
4.2 Receiver 8
5. INSTALLATION 10
5.1 Device Connection 10
5.2 IP Configuration 14
6. WEB USER INTERFACE CONFIGURATION 17
6.1 System 17
6.1.1 [Version Information] 17
6.1.2 [Update Firmware] 18
6.1.3 [Utilities] 20
6.1.4 [Statistics] 21
6.2 Video Wall 23
6.2.1 [Basic Setup] 23
6.2.2 [Advance Setup] 29

6.3 Network: Update the network setup of the
extender system 34
6.3.1 [IP Setup] 35
6.3.2 [Casting Mode] 36
6.4 Functions: 37
6.4.1 [Video over IP]: Setup the video output
mode 39
6.4.2 [USB over IP]: Setup the USB extension
mode 41
6.4.3 [Serial over IP]: set up the serial extension
mode 42
7. BROADCAST CONFIGURATION SETTING 44
7.1 Multicast : 44
7.2 Unicast: 45
7.3 Matrix: 45
7.4 Video Wall: 46
7.4.1 [Basic Setup] 46
7.4.2 Advanced Setup 47
8. PACKAGE CONTENTS 52

Partilink Technology Co., Ltd Copyright @ 2017
3
1. INTRODUCTION
The 4K HDMI & USB over IP Extender is a solution for
audio, video and USB signal extension via Local Area
Network (LAN). It can be used as audio, video and
KVM extender over IP and applied to point to point,
point to multi-point, multi-point to multi-point and
screen wall broadcast system controlled by USB, RS-
232, IR and configured the 4K HDMI & USB over IP
Extender by web browser. An easy installation system
built up with Giga Ethernet switch which has IGMP
function and CATx cable for extension or broadcast.
The P4K-HUL4E1-P supports PoE (Power over
Ethernet) function.

Partilink Technology Co., Ltd Copyright @ 2017
4
2. FEATURES & APPLICATIONS
4K HDMI over IP extension
USB 2.0 over IP extension
RS-232 bi-directional extension
4-bit DIP switch for 16 stream channel selection
HDCP 1.4 compliant and Blu-Ray ready
Support two-way IR extension
Output video rotation
Output video partial enlargement
Automatic EDID configuration
Networking environment under Giga Ethernet switch
and CATx cable
Point to point extension, unicast, multicast and
screen wall system.
Point to point extension via CAT5e cable without
Ethernet switch up to 100M
Ethernet webpage management
RS-232 Serial control command management
P4K-HUL4E1-P supports Power over Ethernet

Partilink Technology Co., Ltd Copyright @ 2017
5
3. SPECIFICATION
P4K-HUL4E1
P4K-HUL4E1-P
4K UHD HDMI
Over IP Extender
P4K-HRSUL4E1
P4K-HRSUL4E1-P
Transmitter
P4K- LHRSU1E4
P4K-LHRSU1E4-P
Receiver
VIDEO INPUT
HDMI Type-A female
connector
None
VIDEO OUTPUT
HDMI Type-A female
connector for loop through
VGA DB-15 female local
output
HDMI Type-A female connector
IR
2x 3.5mm phone jack for IR emitter and receiver to control video
source device
COMPRESSION
Visual lossless compression
HDMI
INPUT RESOLUTION
3840x2160 30/24, 1080p 60/50, 1080p 30/25, 1080i 60/50
720p 60/50, 480i 60/50, 480p 60/50
HDMI
OUTPUT RESOLUTION
3840x2160 30/24, 1080p 30/25, 1080i 60/50,720p 60/50
480i 60/50, 480p 60/50
VGA
OUTPUT RESOLUTION
1080p 30/25, 1080i 60/50, 720p 60/50
480i 60/50, 480p 60/50
AUDIO FORMAT
Stereo 192Kbps
IP PROTOCOL
TCP, UDP, RTSP, RTP, DHCP, IGMP, Multicast, IPV4
LAN PORT
RJ45 connector for Giga Ethernet
SERIAL
DB-9 male connector for RS-232 extension
MANAGEMENT
LAN port
None
Embedded webpage
management
HDMI Type-A female connector
POWER INPUT
2.0mm power jack for DC12V/2A input
OPERATING TEMPERATURE
0~55℃
OPERATING
HUMIDITY
5%~90% RH
POWER SUPPLY
Power adapter AC in 100~240V (50~60Hz)
ESD
ESD protection air gap discharge ±8KV,
contact discharged ±4KV
DIMENSION
194 x 114 x 28 mm
WEIGHT
TX 620g, RX 610g
** Product specifications are subject to change without notice.

Partilink Technology Co., Ltd Copyright @ 2017
6
4. HARDWARE DESCRIPTION
4.1 Transmitter
P4K-HUL4E1/ 4K-HUL4E1-P (TX)

Partilink Technology Co., Ltd Copyright @ 2017
7
1. 12 VDC power supply with locking for 4K HDMI &
USB over IP Extender.
2. RCA connector for stereo audio output.
3. RCA connector for stereo audio input.
4. HDMI video input connector
5. 10/100/1000 Mbps self-adaptive Ethernet interface.
6. ACT LED indicator turns green when 4K HDMI &
USB over IP Extender is powered up.
7. LINK LED indicator flickers green when network
connection is waiting for video source, turns green
when network connection and video source is
functioning properly
8. DB9 connector for RS-232 remote extension
9. Connect IR extension cable to IR port and position
the emitters near the devices you want to control
10. PC USB port for remote additional device such as
USB mouse, USB keyboard and USB pen drive
connecting to PC
11. Group configuration, 4-bit DIP switch to set up the
group ID
12. Restart the 4K HDMI & USB over IP extension by
pressing RESET button

Partilink Technology Co., Ltd Copyright @ 2017
8
13. Press EDID button for manual EDID copy function
14. DB9 connector for VGA local display
4.2 Receiver
P4K-LHRSU1E4/ P4K-LHRSU1E4-P (RX)
1. 12 VDC power supply with locking for 4K HDMI &

Partilink Technology Co., Ltd Copyright @ 2017
9
USB over IP Extender.
2. RCA connector for stereo audio output.
3. RCA connector for stereo audio input.
4. HDMI video input connector
5. 10/100/1000 Mbps self-adaptive Ethernet interface.
6. ACT LED indicator turns green when 4K HDMI &
USB over IP Extender is powered up.
7. LINK LED indicator flickers green when network
connection is waiting for video source, turns green
when network connection and video source is
functioning properly
8. DB9 connector for RS-232 remote extension
9. Connect IR extension cable to IR port and position
the emitters near the devices you want to control
10. Group configuration, 4-bit DIP switch to set up the
group ID
11. Restart the 4K HDMI & USB over IP extension by
pressing RESET button
12. Press EDID button for manual EDID copy function
13. 4 USB ports for additional USB devices such as
USB mouse, USB keyboard and USB pen drive.
Group Setting via 4-bit DIP switch
TX
RX

Partilink Technology Co., Ltd Copyright @ 2017
10
Setting the Transmitter and Receiver group ID via the 4-bit
DIP switch. The correspondent receivers are required to
switch to the same ID as the receiver. It can set up maximum
16 Group IDs. Reboot the system to apply the group setting.
5. INSTALLATION
5.1 Device Connection
1. Check the power supply is unplugged.
2. Set up the group of the transmitter with the
correspondent receiver for signal extension and
display.
3. Connect the Transmitter to video source with HDMI
cable, and connect Receiver to a monitor or display
with HDMI cable.
4. Connect the USB cables from Transmitter to PC,
and connect the USB additional devices such as
USB mouse, USB keyboard and USB pen drive to
Receiver.

Partilink Technology Co., Ltd Copyright @ 2017
11
5. Connect Transmitter and Receiver to the Ethernet
switch with network cable.
6. Power on the Transmitter, Receiver and all the
connected devices.
7. Power on and activate all the connected devices.
8. Connect the IR extension cable with Transmitter
and the IR receiver cable with Receiver for remote
control.
◆Configuration
◆Application Pattern

Partilink Technology Co., Ltd Copyright @ 2017
12
■ Unicast
■ Multicast
a. Video Distribution
b. Matrix Distribution

Partilink Technology Co., Ltd Copyright @ 2017
13
c. Billboard & Kiosk, PC to HDMI and USB
Interactive Monitor
■ Screen Wall

Partilink Technology Co., Ltd Copyright @ 2017
14
5.2 IP Configuration
The 4K HDMI & USB Over IP Extender can configure
via LAN in the same subnet.
1. Assign a LAN IP address to the computer in the
same subnet. The IP address default of the
Transmitter and Receiver is B class Networking:
169.254.xxx.xxx.

Partilink Technology Co., Ltd Copyright @ 2017
15
Figure 1. Internet Protocol (TCP/IP) Properties
2. Connect all devices with proper cables except
video source, please refer to Figure 2
Figure 2. Demonstrate the 4K HDMI & USB Over IP Extender

Partilink Technology Co., Ltd Copyright @ 2017
16
3. After activation, the device information including
the Transmitter and Receiver IP address will be
shown in the lower right corner. Remember the
Transmitter and Receiver IP address on monitor
screen and then plug HDMI video source cable
into Transmitter.
4. The administrator can input Transmitter or
Receiver IP address into address bar of web
browser to enter the Extender Web UI. If link
success, administrator will see the Web UI as
shown in Figure 4.
Figure 3. Device IP Indication

Partilink Technology Co., Ltd Copyright @ 2017
17
Figure4. Web User Interface
6. WEB USER INTERFACE CONFIGURATION
6.1 System
The relevant information of the connected extender
and setting
6.1.1 [Version Information]
Indicating the firmware version and relevant
information of the devices

Partilink Technology Co., Ltd Copyright @ 2017
18
Figure 5. Version Information of the Extender
6.1.2 [Update Firmware]
To update the firmware of the connected extender,
please click on the [Select File] to select the
firmware and click on [Upload] to upload the
firmware and update accordingly.
Figure 6. Update Firmware
Transmitter Firmware Update: please select