Connect tConnect to Softwaro Softwaree
1. Power on the Smart Cart.
2. Open Capstone or SPARKvue then:
Click Hardware Setup. Click Sensor Data.
3. Select the device that matches the ID labeled on your cart.
IMPORTANT: When the device is connected to the software, you
may receive a notification to install a firmware update. Click Yes to
update the firmware.
ContrControl the Motol the Motoror
The on/off state and speed of the motor are set using a control panel in
PASCO Capstone or SPARKvue.
NOTE: You must first connect the motor to a Smart Cart and
connect the Smart Cart to software to access the control panel.
Access the ContrAccess the Control Pol Panelanel
Click Smart Motor in the
Tools palette.
NOTE: If on the Sensor
Data Configuration screen, click
Cancel to return to the Choose a
Path screen.
1. On the Choose a Path screen,
click Build New Experiment.
2. Select any layout.
3. Select the Smart Cart Motor
Display .
PPower the Motower the Motor On and Offor On and Off
Do either of the following to power the motor on or off:
• Click the On and Off buttons.
• Select the Auto checkbox. The motor will automatically power on
when recording data and power off when data collection stops.
Set the Speed and DirSet the Speed and Directionection
Do either of the following to set the speed and direction of the motor:
• Enter a value between -100 and +100 in the Power text box.
• Click and drag the Power slider between -100 and +100.
Additional ContrAdditional Control Methodsol Methods
You can also control the motor by using the following methods listed
below. Detailed directions on how to use these methods can be found in
the Capstone or SPARKvue Help system.
• Blockly Programming
• Calculation (Capstone only)
• Start and Stop Conditions (Capstone only)
Additional ResourAdditional Resourcesces
ExperimentsExperiments
Print-ready experiment worksheets for this product are available to
download from the PASCO website. Go to pasco.com/freelabs and enter
ME-1247 to access all experiments related to this product.
SoftwarSoftware Helpe Help
Additional information on how to use this device can be found in the
PASCO Capstone and SPARKvue Help systems. To access the help:
In the menu bar, click Help then
select PASCO Capstone Help.
Click the Main menu then
select Help.
TTechnical Supporechnical Supportt
Contact PASCO Technical Support for assistance with this or any other
PASCO product.
Address PASCO scientific
10101 Foothills Blvd.
Roseville, CA 95747-7100
Phone 1-800-772-8700 (USA)
1-916-462-8384 (International)
Chat www.pasco.com
RegulatRegulatorory Informationy Information
PrProduct End of Lifoduct End of Life Disposal Instructionse Disposal Instructions
This electronic product is subject to disposal and recycling regulations that vary by country and
region. It is your responsibility to recycle your electronic equipment per your local environmental
laws and regulations to ensure that it will be recycled in a manner that protects human health and
the environment. To find out where you can drop off your waste equipment for recycling, please
contact your local waste recycle or disposal service, or the place where you purchased the product.
The European Union WEEE (Waste Electronic and Electrical Equipment) symbol and on the
product or its packaging indicates that this product must not be disposed of in a standard waste container.
BatterBattery Disposal Instructionsy Disposal Instructions
Batteries contain chemicals that, if released, may affect the environment and human health. Batteries should be
collected separately for recycling and recycled at a local hazardous material disposal location adhering to your
country and local government regulations. To find out where you can drop off your waste battery for recycling,
please contact your local waste disposal service, or the product representative. The battery used in this product
is marked with the International symbols to indicate the need for the separate collection and recycling of
batteries.
CE StatementCE Statement
This device has been tested and found to comply with the essential requirements and other relevant provisions
of the applicable EU Directives.
FCC StatementFCC Statement
This Class A digital device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WWarrarrantyanty, Cop, Copyright, and Tyright, and Trrademarksademarks
Limited WLimited Warrarrantyanty
For a description of the product warranty, see the Warranty and Returns page at www.pasco.com/legal.
CopCopyrightyright
This document is copyrighted with all rights reserved. Permission is granted to non-profit educational
institutions for reproduction of any part of this manual, providing the reproductions are used only in their
laboratories and classrooms, and are not sold for profit. Reproduction under any other circumstances, without
the written consent of PASCO scientific, is prohibited.
TTrrademarksademarks
PASCO and PASCO scientific are trademarks or registered trademarks of PASCO scientific, in the United
States and/or in other countries. All other brands, products, or service names are or may be trademarks or
service marks of, and are used to identify, products or services of, their respective owners. For more
information visit www.pasco.com/legal.
