Paslode IMPULSE B20722 User manual

PASLODE IMPULSE
TRIMMASTER 16A
ANGLED BRADDER MANUAL
ANZ Product Code B20722
IMPORTANT!
Updated maintenance
schedule instructions

1 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 2
Congratulations on the purchase of your new Paslode Cordless TrimMaster 16A Angled Bradder.
GENERAL SAFETY INSTRUCTIONSTABLE OF CONTENTS
The Impulse system consists of: tool, fuel cell, battery,
charger and fasteners. In the interests of operator
and system safety, the tool, fasteners and the fuel
cells referred to in the Paslode documents, must be
considered as one single, complete safety system.
WARNINGS
DO NOT ATTEMPT TO OPERATE
THIS TOOL UNTIL YOU HAVE
READ AND UNDERSTAND ALL
SAFETY PRECAUTIONS AND
MANUAL INSTRUCTIONS.
The Paslode Cordless TrimMaster 16A
Angled Bradder is an internal combustion
device. It produces hot exhaust gases
that may ignite flammable materials. This
tool must not be used in a combustible
environment or in the presence of
combustible materials, such as flammable
chemicals, adhesives, gasoline, or
solvents.
Failure to follow all safety precautions and
instructions may result in a permanent
loss of vision, serious personal or even
fatal injury, property damage and/or tool
damage.
Do not expose the tool to temperatures in
excess of 49°C (120°F). Fuel and/or the
battery may burst, releasing flammable
gas.
This tool must be operated only in a well-
ventilated environment, because the tool
exhausts carbon monoxide similar to a
petrol/gasoline lawnmower. Exposure to
carbon monoxide may cause dizziness,
nausea, or unconsciousness.
ALWAYS keep the Paslode Cordless
TrimMaster 16A Angled Bradder fuel cell,
battery and battery charger out of the
reach of children.
ALWAYS wear eye and ear safety
equipment (PPE) when working with
or in the vicinity of the Paslode Impulse
16A TrimMaster.
The Impulse 16A TrimMaster should not
be used in the rain or where excessive
moisture is present.
MAINTENANCE
Restrict Field Maintenance to the following:
CHECKING THE ENERGY LEVEL OF THE BATTERY
RECHARGING THE BATTERY
CHECKING THE FUEL CELL
REPLACING THE FUEL
CLEANING/REPLACING THE AIR FILTER
CLEARING A JAM
CLEANING AND LUBRICATING THE TOOL
(SEE UPDATED INSTRUCTIONS VIA QR CODE (PG 11)
CAUTION
Never attempt any maintenance of a
Paslode Impulse tool without first
removing the fasteners, fuel cell and
battery. Maintenance should be started
only after the tool is inoperative.
Operators should be capable of conducting basic
maintenance on the tool. This will not affect your tool
warranty.
FUEL CELL CHECK
Check the fuel cell. First remove the fuel cell from the tool
and check the “Best Use Before” date stamped on the
bottom of the cell.
CLEARING A NAIL JAM SAFELY
1. Remove the battery, fuel and fasteners.
2. Lift the Nose Plate latch to expose the Brad.
3. Clear jam, and push driver blade back up to its
rest position at the top of the cylinder.
4. Close Nose Plate and reset the latch.
FUEL CELL DISPOSAL
Dispose of all empty fuel cells responsibly. Remember to
dispose of these fuel cells where they will not be crushed,
punctured, burned or found by children.
Refer to your local authority regulations.
GENERAL SAFETY INSTRUCTIONS ..................................................................2
TOOL SAFETY INSTRUCTIONS .........................................................................3
BATTERY SAFETY & CHARGING ......................................................................4
FUEL CELL SAFETY...........................................................................................5
TOOL OVERVIEW...............................................................................................6
FUEL CELL LOADING PROCEDURE ................................................................7
CORRECT TOOL OPERATING PROCEDURES..................................................8
PREPARING AND USE OF TOOL ......................................................................9
TROUBLESHOOTING ........................................................................................10
TOOL MAINTENANCE ......................................................................................11
TOOL SPECIFICATIONS ....................................................................................12
SCHEMATICS ....................................................................................................13

3 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 4
TOOL SAFETY INSTRUCTIONS
SAFETY INSTRUCTION:
TOOL OPERATION
1. EYE AND EAR PROTECTION.
Eye protection must meet the requirements
of AS/NZS 1337:1992 and should have side
shields for increased protection.
2. NEVER ASSUME THE TOOL IS EMPTY.
Never point the tool at yourself or anyone else.
3. NEVER ENGAGE IN “HORSEPLAY” WITH THE
TOOL.
Careless and improper use may results in a serious
accident.
4. NEVER CARRY THE TOOL WITH YOUR FINGER
ON, OR DEPRESSING, THE TRIGGER.
This practice may result in an accidental discharge
or a fastener.
5. NEVER OPERATE A TOOL THAT IS
MALFUNCTIONING.
Repair or refer to a service agent.
6. DO NOT LOAD FASTENERS WITH
THE TRIGGER OR SAFETY YOKE DEPRESSED.
A fastener may be accidentally discharged.
7. NEVER OPERATE THE TOOL WITH THE WORK
CONTACT ELEMENT REMOVED OR DISABLED.
Never operate the tool if the work contact element
is not working properly or sliding freely.
8. ALWAYS POINT THE TOOL AWAY FROM YOUR-
SELF AND OTHERS WHEN CLEARING A JAM OR
REMOVING FASTENERS. ALWAYS REMOVE THE
FUEL CELL AND BATTERY BEFORE CHECKING
THE TOOL.
9. NEVER OPERATE THE IMPULSE TRIMMASTER
IF PARTS ARE LOOSE, DAMAGED OR MISSING.
10. DO NOT DRIVE FASTENERS INTO KNOTS OR
ON TOP OF OTHER FASTENERS.
A fastener may ricochet and cause serious injury.
11. OPERATE THE TOOL ONLY ON THE WORKPIECE.
12. NEVER DRIVE FASTENERS INTO AREAS WITH
CONCEALED HAZARDS.
Always check the area behind the work surface for
electrical wiring, gas, pipes, water pipes, sewer drains
or other potential hazards.
13. ALWAYS MAINTAIN SECURE AND
UNOBSTRUCTED FOOTING WHEN ON LADDERS,
PLATFORMS OR OTHER HIGH LOCATIONS.
14. ALLOW ONLY QUALIFIED PERSONNEL TO
OPERATE THE IMPULSE TRIMMASTER.
15. PROPERLY STORE FUEL CELL.
Always store fuel cells where they will not be
exposed to an open flame, sparks, in direct
sunlight or temperatures above 25°C.
16. ALWAYS STORE THE TOOL WITH THE FUEL CELL
AND BATTERY REMOVED.
Store the fuel cells in the case with the Impulse
TrimMaster.
17. KEEP THE TOOL CLEAN AND WELL MAINTAINED.
18. KEEP YOUR HANDS CLEAR OF THE WORK
AREA SURFACE.
A fastener may exit at an angle
unexpectedly and cause injury.
19. OBSERVE LOCAL BATTERY AND FUEL CELL
DISPOSAL REGULATIONS.
20. WHEN NOT IN USE, REMOVE THE BATTERY
AND FASTENERS AND RETURN THE TOOL
TO ITS CASE.
21. IT IS NOT PERMITTED TO MAKE ANY
MODIFICATION TO THE TOOL, FUEL CELL OR
BATTERY OTHER THAN THOSE SPECIFIED BY
THE MANUFACTURER.
22. ONLY USE PASLODE SPECIFIED CONSUMABLES,
BATTERIES AND FUEL CELLS. CONSUMABLES,
BATTERY AND FUEL CELLS ARE A COMBINED
SAFETY SYSTEM.
23. IF THE TOOL MISFIRES, ALWAYS REMOVE THE
BATTERY PRIOR TO EXAMINATION OF THE TOOL.
If the problem persists contact your local centre or
the tool manufacturer. The tool should be regularly
inspected for defective parts, loose screws (especially
after cleaning), etc and any defects rectified before
use. Check prior to each operation that the safety
mechanism is functioning properly.
BATTERY SAFETY & CHARGING
BATTERY AND CHARGING INSTRUCTIONS
1. Plug power adapter into charger base.
2. Connect to 240v AC outlet, a green light
indicates power is on.
3. Install battery, red light indicates battery is charging.
NOTE: If battery is completely discharged, the red
light and the green light may alternate back and
forth for up to 20 minutes. This safety feature slowly
recharges the battery until it is ready to accept the
full charging current. If the red and green lights
continue to alternate after 20 minutes, the battery
may be damaged.
4. After charging is complete, the green light will come on.
CHARGING TIMES
First charge (new battery) - 1 hour
Discharged Battery - 5 minutes to 1 hour
DO NOT:
Charge battery outdoors, in exposed wet
conditions, or in temperatures below 5°C
(40°F).
Allow metal objects to come in contact with
battery terminals.
Puncture or attempt to open battery case
or cells.
Store battery where it will be subjected to
temperatures above 49°C (120°F).
Incinerate battery.
Use a defective battery charger, one that
over-heats and/or smokes when plugged in.
Immerse the battery in water.
Do not short-circuit a battery.
Do not use a battery charger which heats
up excessively or gives off fumes when
connected - disconnect the charger
immediately.
The power adapter, charger base and battery are
designed to operate together as one system. Only use the
‘Paslode Impulse’ charger for ‘Paslode Impulse’ batteries.
The charging system is designed for use in covered areas.
Do not expose it to rain or to excessive humidity.
Arrange the charger lead appropriately to avoid
unnecessary damage. Do not use the charger if the cable
or plug is damaged. Replace immediately.
To avoid electrocution, disconnect the power supply
adapter before cleaning the terminals and contacts.
Use a dry cloth.
BATTERY DISPOSAL
Batteries and charging systems must be recycled or
taken to a designated disposal areas. (Subject to local
regulations)
TRANSPORT - LI ION BATTERY
& FUEL CELLS
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements (see UN3480
or UN3481). The user can transport the batteries by road
without further requirements.
When being transported by third parties (eg: air transport
or forwarding agency), special requirements on packaging
and labelling must be observed. For preparation of the
item being shipped, consult an expert for hazardous
material if required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations.
For the transport of Paslode fuel cells use UN Code
UN3478.
Transport of small amounts (<30 Kg ) in a private vehicle
is permitted without a transport and safety sheet (Limited
quantity exemption for road transport). The regulations by
transport categories are:
• Road/rail: ADR- RID - UN code 3478 class 2 code 5F
• Sea: IMDG - UN code 3478 + emergency instructions
sheet F·D, S-U
• Air: IATA - UN code 3478 class 2.1
Goods must be accompanied by the written safety
instruction of the chapter 5·4·3 of the ADR. Transport
by post is not permitted.

5 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 6
FUEL CELL SAFETY
FUEL CELL SAFETY
WARNING
EXPLOSION/FIRE HAZARD
Read all instructions before using
or handling the fuel cell.
Keep the fuel cell away from heat, sparks
and open flame. Do not smoke when
handling or operating tool or fuel cell.
Exposure to temperatures above 49°C
(120°F) may cause the fuel cell to burst,
releasing flammable gas.
Sunlight can raise the inside temperature
of an unventilated motor vehicle or storage
container to above 60°C (140°F).
Never puncture or attempt to open
the fuel cell; it is non-refillable. Never
incinerate, reclaim or recycle the fuel cell.
Dispose of used cell responsibly.
Never smoke while installing the fuel
cell or operating the tool.
Never inhale the spray.
Store fuel cell(s) in well-ventilated areas
only.
Keep out of the reach of children.
Liquid gas can cause injury in the event
of contact with the skin or eyes.
FUEL CELL CHECK
Paslode Impulse fuel cells are marked with
a “Best Use Before” date on the bottom of
the can. For maximum performance use
fuel before the “Best Use Before” date.
COLD WEATHER OPERATION
Fuel combustion can be adversely affected at extreme low
temperatures. Ensure that the tool battery and fuel cell are
above the minimum operating temperature of 7°C (20°F)
before use.
The fuel cell is an aerosol product corresponding to the
2008/47/EC regulations. It contains:
• Liquefied hydrocarbon gases (butane, propane,
propylene).
• A lubricant to maximise the tool durability.
When the fuel is used there will always be some
propellant left inside the cartridge. The fuel cell is always
pressurized. Its contents are extremely flammable. The
fuel cell is not reusable.
FUEL CELL DISPOSAL
Dispose of all empty fuel cells responsibly. Remember to
dispose of these fuel cells where they will not be crushed,
punctured, burned or found by children.
STORAGE
Stores and showrooms must comply with building
regulations. All local instructions corresponding to fire
regulations must be followed.
• Where possible, store fuel at a stable temperature in
the range 7°C to 25°C. Do not expose to temperatures
exceeding 49°C.
• Do not use tools that emit flames, sparks or reach high
temperatures in the vicinity where fuel cells are stored.
• Do not store in designated thoroughfares, hallways or
stairwells.
• Store in a well-ventilated area.
• Fuel cells must not be displayed in shop windows.
• Storage with pyrotechnic products is not permitted.
FIRST AID
• Direct contact with liquid gas may cause burns or
frostbite.
• In case of inhalation remove the person to fresh air,
and encourage breathing. Should the casualty become
unconscious, or breathing does not quickly return to
normal, summon urgent medical assistance.
• If gas gets into the eyes they should be flushed out with
copious amounts of water. Skin contamination should
be removed with soapy water.
If symptoms persist, seek medical assistance.
TOOL OVERVIEW
FLASHING GREEN
= CHARGED
FLASHING RED
= NEEDS CHARGING
QUICK RELEASE -
NOSE PLATE ASSEMBLY
NO MAR WORK CONTACT TIP
DEPTH OF DRIVE ADJUSTMENT
TOOL REST FIXTURE
BYPASS FOLLOWER
SOFT GRIP HANDLE
REAR LOAD MAGAZINE
SOFT RUBBER TRIGGER
=
=
BATTERY OFF / ON
OFFOFF ONON
ADJUSTABLE BELT HOOK - RAFTER HOOK

TRIMMASTER 16A ANGLED BRADDER MANUAL 87 TRIMMASTER 16A ANGLED BRADDER MANUAL
FUEL CELL LOADING PROCEDURE
1,000
shots
per
cell
Fuel cell
expiry
on base
of can
CORRECT FUEL CELL LOADING PROCEDURE
To open - Push forward, lift then
back
Open fuel door assembly #33
Carefully align fuel adaptor and cell
stem
Raise fuel tube block assembly, will
lock in up position. Part #9 & 10
Open fuel door fully
Load fuel cell
To close - Push forward then down
to lock fuel door
Note: Fuel Cell Dosing Lever must
be in the down position
Load
fuel
cell
65
7 7
1 2 3
4
ONLY USE PASLODE’S SPECIALLY FORMULATED FUEL, FAILURE TO DO SO MAY DAMAGE YOUR TOOL,
CAUSE MISFIRES AND VOID WARRANTY.
49°
ALWAYS REMOVE BATTERY,
FUEL CELL AND FASTENERS
WHEN SERVICING OR CLEARING A JAM.
8
CORRECT TOOL OPERATING PROCEDURES
= 50 brads per strip, 2 strips per load
1.6mm Smooth Shank
Lengths 32 to 63mm
Lost Tee Head
Zinc Plated & Stainless Steel
CORRECT NAIL LOADING PROCEDURE
Insert selected brads into magazine Make sure top of head aligns with
Head supporting Brad Channel
Note: Brads are still behind follower
Depress follower lever #68 Pull bypass follower back past brad
strip to engage brads
Allow follower to rest behind brad
strip
Allow brad follower to rest behind
brad strip
1 2 3
4 5 6
7

+ +
9 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 10
PREPARING AND USE OF TOOL
ADJUSTING THE DEPTH OF DRIVE - THUMB WHEEL ROTATION
Counter
Sunk Proud
INCREASE
DEPTH OF DRIVE
DECREASE
DEPTH OF DRIVE
TOOL FIRING SEQUENCE 1000/hour max fire rate / 2-3 nails a second / -3ºC to 40ºC
BANG!
1 2 3 4
Depress work contact tip Actuate trigger, tool fires Allow tool to recoil off
work surface, work
contact is released
With trigger released, tool
will reset for next shot -
sequential operation
CORRECT BATTERY OPERATION
ON/OFF SWITCH. Battery has 2 secure lock positions:
engaged and disengaged. Press in to engage battery.
OFFOFF ONON
Green indicates
charged battery
Red indicates battery
needs recharging
BZZZZZ
ALWAYS WEAR EYE AND HEARING PROTECTION
49°
+ +
Counter
Sunk
TROUBLESHOOTING
FIRING THE TOOL
Tool Working Correctly Fan starts - Tool Fires
PROBLEM: No fan and
does not fire
SOLUTION:
• Check for flat battery
• Remove and reinsert battery to reset tool
• Check for flat battery and recharge battery
PROBLEM:
Fan runs but tool
does not fire
SOLUTION:
• Check for empty fuel cell, flat battery, clogged filter or dirty spark plug
• Clean and oil tool
• Check driver blade returned to top of cylinder
PROBLEM:
Fan runs, tool fires,
no nail fed.
SOLUTION:
• Remove jammed nail
• See instruction below
BZZZZZ
BANG!
BANG
BZZZZZ
BANG
BZZZZZ
BZZZZZ
BANG!
49°
ALWAYS REMOVE BATTERY,
FUEL CELL AND FASTENERS
WHEN SERVICING OR CLEARING A JAM.

11 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 12
TOOL MAINTENANCE
CLEARING A FASTENER JAM
Only if needed to clear
jam - remove No Mar
Contact Probe #62 & 63
No Mar Probe removed,
allows greater assess to
remove a jammed brad
Align probe leg with hole
in Depth of Drive adjuster
Refit No Mar Probe
Lift nose plate cover
to release nose plate
assembly #60
Verify driver piston
assembly #22 is returned
to top position prior to
firing tool
Close nose plate
assembly #60
Close nose plate cover
#60
Clip nose plate cover
assembly pin over nose
location studs #64
TIP: It may be easier to clear a nail jam by first returning the driver blade to top rest position with a small diameter punch.
Then remove the nail.
Lift nose plate #60 Remove jammed brad
49°
ALWAYS REMOVE BATTERY,
FUEL CELL AND FASTENERS
WHEN SERVICING OR CLEARING A JAM.
4A 4B 4C
IMPORTANT!
Please scan QR code for latest maintenance schedule.
Procedures have changed since prior TrimMaster models.
TOOL SPECIFICATIONS
PASLODE IMPULSE TRIMMASTER 16A ANGLED BRADDER
MAX FIRE RATE FIRE RATE TEMPERATURE RANGE
hours seconds Celcius
1000 2 - 3 nails per second -3 to 40 degrees C
TOOL
SIZE
TOOL
WEIGHT
MAGAZINE
CAPACITY
NAIL
SIZE
COLLATION
TYPE
SHANK
TYPES
TYPE OF
HEAD
DURABILITY
mm kg Unit mm 20º Degree
Height:
269mm
(10.6in)
Length:
300mm
(11.8in)
Width:
82mm
(3.5in)
1.95kg
(4.3lb)
without
battery
2.13kg
(4.7lb)
with
battery
100 brads
x 2 strips
reload
Length: 32 to 63mm
Diameter: 1.6mm
Adhesive
Collation
Smooth Lost Tee
Head
Zinc Plated and
Stainless Steel
LI-ION BATTERY AND CHARGER SYSTEM
TECHNICAL DATA PART NO INPUT OUTPUT POLARITY
Power Adapter 240V AC
50/60 Hz
30W
12VDC @ 1.8A
12V @ 1.8A
Battery Charger Kit
B20543B
8.5VDC @ 2.0A
Battery
B20543A
7.4 VDC Li-Ion 9.3Wh 1250mAhr
10,000 shots per charge
Fuel Cell Capacity
1,000 shots
Note: Use black moulded fuel cell cap only
123
4D
5 6 7 8

13 TRIMMASTER 16A ANGLED BRADDER MANUAL TRIMMASTER 16A ANGLED BRADDER MANUAL 14
SCHEMATICS
16
⚫
18
17
8
5
All parts sold as single items unless described as a set etc., or
forms part of an assembly (multiple items defined within a box).
A part with no item number is only available in an assembly.
⚫
71
3
4
19
1
2
33
28
25
29
27
30
31
32
16
⚫
26
⚫
⚫
⚫
⚫
◼
60
36
34
41
38
◼
39
37
38
◼
◼
51
52
53
35
34
71
71
73
72
34
70
43
42
56
58

57
◼
47
49
48
45
46
44
SERVICE KIT
009998
74
Torque Values (in/lb)
Item Torque
Item
Torque
3 30-35 37 45-50
7 20-35 38 45-50
10

15-20 

55-65
14 30-35 44 6-8
17 6-8 65 18-22
25 30-35 66 18-22
62
63
66
67
61
64
65
Bloc k not
in kit 47
IM250ALi MK2
16G Angled Bradder
TrimMaster B20722

◼
59
⚫
Service Kit Item
◼Loctite®242

Grease

68
11
9
9
10
⚫
15
14
12
6
7
13
20
40
54
55
50
69
23
⚫
21
22
24
38 900708 2 Screw SHC B-32 x 1/2 (Red)
39 900754 1 Screw SHC B-32 x 1/2 (Yellow)
40 900726 1 Slide Switch Assembly
41 902439 1 Circuit Board Assembly
42 900662 1 Wire Ribbon, ESU Power
43 916258 1 Electronic Spark Unit (ESU)
44 901082 1 Trigger Assembly
45 900629 1 Bracket, Retaining
46 404702 2 Screw TF 6-32 x 3/8
47 918906A 1 Hook Assembly, Belt
48 918906 1 Hook & Stop Assembly, Belt
49 916911 1 Block
50 902621 1 Pad, Battery
51 916230 1 Channel, Brad
52 916215 1 Plate, Magazine
53 916205 1 Channel, Magazine
54 904562 1 Wire Lead Assembly, Fan Motor
55 904567 1 Spark Wire Lead Assembly
56 916239 1 Spring, Yoke
57 900746 2 Screw 8-32 x 7/16
58 916285 1 Yoke, Knob & Guide Assembly
59 916212 1 Bolt, DoD Adjustment
60 916284 1 Nose Plate Assembly
61 916234 1 Pin, Nose Plate
62 916206 1 Probe
63 902473 1 No Mar Tip (3 Pack)
64 916203 1 Nose
65 900631 1 Spring, Lockout
66 900602 1 Bar, Lockout
67 900630 1 Pin, Lockout
68 900808 1 Follower Assembly
69 900627 1 Spring, Negator
70 916202 1 Handle LH
71 916287 4 Screw TX 8-16 x 3/4
72 916218 1 Body, Follower
73 916287 1 Screw, PH 8-16 x 3/4
74 009998 AR Service Kit
SAFETY INSTRUCTIONS
WEAR EYE AND HEARING PROTECTION
Always wear approved eye and hearing protection when
operating tool.
Ensure others in the near vicinity use the same protective
equipment.
Use eye protection when cleaning tool.
1 916222 1 Grill
*2 900648 1 Filter
3 901064 4 Screw SHC 8-32 x 1-3/8
4 916216 1 Cap
5 901382 1 Motor Assembly, Fan
6 916249 1 Insulator, Spark Plug
7 916236 1 Spark Plug Assembly
8 401356 1 Sleeve, Fan Motor
9 904517 1 Fuel Barb
10 904546 1 Fuel Tube
11 902406 1 Fuel Block
12 904521 1 Arm, Pivot
13 916208 1 Cylinder Head
14 900596 1 Screw TX SEMS 8-32 x 7/16
15 900739 1 Circuit Board Assy, Cylinder Head
* 16 900612 1 Ring, Cylinder Head & Sleeve
17 900709 1 Fan Assembly
18 900700 1 Air Dam
19 900729 1 Combustion Chamber Assembly
*20 900659 1 Seal, Combustion Chamber
21 403099 1 Circlip, Piston
*22 900728 1 Driver & Piston Assembly
* 23 403098 1 Ring, Piston
24 900680 1 Bumper, Piston
25 916288 1 Sleeve Assembly
26 405140 1 Screws 8-32 x 3/8 (Red)
27 900668 1 Cover, Muffler
* 28 900609 1 Muffler
* 29 900664 1 Reed Valve
30 900665 1 Reed Plate
* 31 901089 1 Disk, Pre-Filter Baffle
* 32 900616 1 O-Ring, Exhaust
33 916286 1 Fuel Door Assembly
** 34 916261 1 Label Set
35 916201 1 Handle RH
36 916229 1 Channel, Handle Half Joint
37 916231 1 Flange, Retaining
*Normal Wear Items
** Ensure Warning Label is affixed and legible
Included in Service Kit
Apply Loctite®242 (Blue)
Apply grease to threads
AR as required
WARNING: All parts must be periodically inspected
and replaced if worn or damaged.
Failure to comply can affect the tool’s operation and
present a safety hazard.
SCHEMATICS cont.
PARTS LEGEND PASLODE IMPULSE IM250ALi MK2 16 GAUGE ANGLED BRADDER B20722

15 TRIMMASTER 16A ANGLED BRADDER MANUAL
For technical support contact Paslode:
Australia: 1800-PASLODE (727-563)
New Zealand: 09-477-3000
GTU Part No. 919000
919080 Rev 2
PASLODE AUSTRALIA
PO Box 914 lngleburn 1890
Australia
www.paslode.com.au
PASLODE NEW ZEALAND
PO Box 100 303 NSMC
Auckland New Zealand
www.paslode.co.nz
ACCESSORIES
Paslode Impulse Battery B20543A
Battery Charger system
B20543B
B20543C
B902661
Carry Case
9/64” Hex Key Maintenance tool
5/32” Hex Key Maintenance tool
900736
401331
Impulse Tool Cleaner/Degreaser
Recommended cleaner for Paslode Impulse tools B20544L
No Mar Tips (3 pack) 902473