Patriot lighting 20704 User manual

Black (hot/power)

White (neutral)

Bare/Green

(ground)

White

Red

Black

White

Blue

White

Green

Receiver

1. Use existing pull chains on the desired

fan to set fan speed to HIGH and to turn

the light ON.

2. Turn o circuit breakers and wall switch

to the fan.

DANGER: Failure to disconnect

power supply prior to installation may

result in serious injury or death.

3. Lower the canopy of the previously

assembled fan and insert receiver.

Note: If installing this product with

a new fan, insert the receiver in the

mounting bracket before wiring the

fan; wire the fan according to these

instructions, then continue fan assembly

as directed in the fan’s instruction

manual.

PREMIUM

REMOTE CONTROL

Model #20704 (363-5811)

4. Disconnect existing wire connections,

then secure all wire connections with

wire connectors according to diagram

and these steps:

• Connect the Blue wire with white label

from the receiver to the Blue fan wire.

• Connect the Black wire with white

label from the receiver to the Black fan

wire.

• Connect the White wire with white label

from the receiver to the White fan wire.

• Connect the Red wire with red label

from the receiver to the Black (hot/

power) supply wire.

• Connect the White wire with red

label from the receiver to the White

(neutral) supply wire.

Fan Pull

Chain

Light Pull

Chain

Canopy

High

LED Indicator

Wall Bracket

Mounting

Screw

5. Wrap electrical tape (not included)

around each wire connector down to

the wire. Then, push wire connections

into the outlet box. Place the White wire

connections on the opposite side of the

outlet box from the Black and Blue wire

connections.

6. Reinstall the canopy.

7. Turn on power supply and wall switch to

the fan.

8. Remove the battery cover from the back

of the remote and install the A23 12-

volt battery. Replace the battery cover

and press the HIGH button to ensure

the LED indicator illuminates and the

fan turns on.

9. If desired, the wall bracket can be

attached to a wall using the mounting

screws.

Questions? Call our customer service department at

1-877-459-3267, 9 a.m. - 5 p.m. Central Time.

Remote

Qty. 1

Wall Bracket

Qty. 1

Battery

Qty. 1

Receiver

Qty. 1

Wire Connector

Qty. 5

Mounting Screw

Qty. 2

Owner’s Manual

Qty. 1

Read instructions completely before installing the remote.

WARNING: If the color of the household supply wires is different than what is referred to in the instructions below, a professional electrician should determine proper wiring.

CAUTION:

• Do not install in damp locations. For indoor use only.

• Do not use with fans that have integrated remote controls.

• Be sure the outlet box is properly grounded or that a green or bare (ground) wire is present.

• This unit is intended to control a ceiling fan with electrical source of AC 110/120V, 60Hz.

• To reduce the risk of re or electric shock, do NOT use a full-range dimmer switch to control the fan speed.

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help. Any changes or modications not expressly approved by the grantee of this device could void the user’s

authority to operate the equipment. tt

HKC-US

3350 Players Club Pkwy. #225, Memphis, TN 38125

(877)459-3267

Owner’s

Manual

SAFETY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

1 5

2 6

Warning: Never wire fan to

a wall control. Only wire to a

single-pole on/o wall switch.

Canopy

Front Back

LED Indicator

9552 • 110419

Printed in China

To operate the fan using the remote, press and release the following buttons:

1 - High fan speed

2 - Medium fan speed

3 - Low fan speed

4 - Fan Power: Turns the fan o.

Light Delay O Mode - Press and hold the fan power button (4) for ve seconds, which will turn o light after one

minute. The LED indicator on the remote will ash four times to conrm mode setting.

5 - Light Control: Dimmable Bulbs - Tap button to turn lights o and on. Press and hold button to dim or brighten the lights.

Non-dimmable bulbs - Turns lights on and o. Note: The dimmer function does not work with non-dimmable bulbs.

6 - D/CFL Switch: Switch should be set to “CFL” to correspond with standard non-dimmable bulbs; set to “D” for

incandescent and other dimmable bulbs.

Learn - Syncs remote control to receiver. The remote was synced at the factory. Should it become necessary to re-sync

the remote, turn o the main power, then turn it back on. Within 30 seconds, use a small screwdriver to press and

hold the learn button on the remote for 3 seconds. The fan will turn on and light (if applicable) will blink three times,

signaling a successful synchronization.

OPERATING INSTRUCTIONS

TROUBLESHOOTING

1-YEAR LIMITED WARRANTY

If you have diculty operating your remote, or have diculty with installation, please contact Customer Service : 1-877-459-3267, 9 a.m.-5 p.m. Central time.

WARNING: Ensure the power is turned o to the fan/remote before performing any maintenance.

LED indicator on the remote illuminates, but the remote won’t control the fan. The remote may need to be re-synced.

The remote is synced to the receiver at the factory. Occasionally, power surges can cause the remote to become un-synced. Whenever necessary, follow the syncing instructions

below.

SYNCING INSTRUCTIONS: Turn o the main power, then turn it back on. Within 30 seconds, press and hold the high and low speed buttons on the remote at the same time for 5

seconds. The LED indicator will ash 3 times, signaling a successful synchronization. Once complete, the fan will start on the low speed with the light (if applicable) o.

The LED indicator on the remote does not illuminate.

The battery most likely needs to be replaced or it is not oriented correctly in the battery compartment. If battery is depleted rapidly, ensure one of buttons is not stuck in the

down position.

The LED indicator stays on.

Ensure one of buttons is not stuck in the down position.

Remote controls more than one fan.

Turn o the power to the fans you don’t want synced. Follow the syncing instructions listed above. Then, turn on the power to the other fans.

Dimming feature does not function.

Ensure the “D/CFL” button in the battery compartment is set to the “D” position and the bulbs are incandescent or other dimmable bulbs.

Fan will not run at high speed. If you fan has manual pull chains to operate the fan speed, be sure the pull chain is manually set to HIGH SPEED. If your pull chain is set to LOW or

MEDIUM SPEED, the remote will not override the manual pull chain setting.

Light will not turn on. If you fan has manual pull chains, be sure the light pull chain is set to ON. The remote will not override the manual pull chain setting.

To obtain service, please contact the Service Department:

1-877-459-3267, 9 a.m.- 5 p.m. Central time.

The manufacturer warrants all of its lighting xtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product

is found to be defective, take a copy of the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The manufacturer will, at its option,

repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the xture is the responsibility of the consumer. This warranty does not cover

xtures becoming defective due to misuse, accidental damage or improper handling and/or installation and specically excludes liability for direct, incidental or consequential

damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specic rights