Patton electronics SMARTNODE 4552 User manual

SmartNode 4552
ISDN SoHo VoIP Gateway Router
Quick Start Guide
Approbacion
Este aparato esta aprobado para conexion a red publica ISDN sobre interfaz BRI/So.
Approbation
Cet appareil est approuve pour la connexion au reseau ISDN public avec les interfaces BRI/So.
Zulassung
Zugelassen fur die Anshaltung an da offentliche ISDN Telekommunikatinosnetz an BRI/So- ISDN Schnittstellen.
Approval
This device is approved for connection to the public ISDN telecommunication network. over a BRI/So-ISDN interfaces.
Sales Office: [phone]
Technical Support: [phone]
E-mail: [email protected]
WWW: www.patton.com
Document Number: 13216U7-001 Rev. B
Part Number: 07MSN4552-QS
Revised: February 25, 2005

Patton Electronics Company, Inc.
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Tel: [phone]
Fax: [phone]
Support: [phone]
Web: www.patton.com
E-mail: [email protected]m
Trademark Statement
The terms SmartNode, SmartWare and SmartView are trademarks of Patton
Electronics Company. All other trademarks presented in this document are the
property of their respective owners.
Copyright © 2004–2005, Patton Electronics Company. All rights
reserved.
The information in this document is subject to change without notice. Patton
Electronics assumes no liability for errors that may appear in this document.
Important Information
To use virtual private network (VPN) and/or AES/DES/3DES encryption
capabilities with the SmartNode 4552, you may need to purchase additional
licenses, hardware, software, network connection, and/or service. Contact
[email protected] or [phone] for assistance.
ii

SmartNode™
SN4552 QUICK START GUIDE
This Quick Start Guide leads you through the basic steps to set up a new SmartNode and to download a
configuration. Please note that this guide does not replace the detailed Software Configuration Guide and the
Getting Started Guide available on the CD-ROM and online at www.patton.com/voip.
Your SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the
configuration of the SmartNodes configuration templates for the most important applications are available
online at http://www.patton.com/voip/appnotes.shtml .
Tthe main steps to set up a new SmartNode are shown below.
Connect a PC, login and configure the IP address
Connect the SmartNode to the Network
Download a configuration example, adapt to your network and load
onto the SmartNode
1

SmartNode™
Connect a PC, login and configure the IP address
Power Connection and Default IP Configuration
First the SmartNode must be connected to the mains power supply using the included power supply. Wait
until the ‘PWR' LED stops blinking and lights constantly. Now the SmartNode is ready.
The factory default IP settings are as follows:
LAN ports (green, ETH 0/1): IP Address: 192.168.1.1 Network Mask: 255.255.255.0
WAN port (red, ETH 0/0): IP Address: 172.16.40.1 Network Mask: 255.255.0.0
A DHCP Server with address space 192.168.1.10 – 192.168.1.19 is running on the LAN ports
Both Ethernet ports are pre-configured and active.
If these addresses conflict or do not match with your network they must be changed. Contact your network
administrator if you are not sure what IP address to use in your installation.
PC connection and Login
To access the SmartNode configuration connect a PC with Ethernet port to one of the LAN ports (green) of the
SN4552. Use the included black Ethernet cable for this purpose. Set your PCs TCP/IP configuration to DHCP
to automatically receive an IP address from the SmartNode.
Open a Telnet connection to the default LAN IP address of the SmartNode (192.168.1.1). Use the Terminal
program included with most PC operating systems (e.g. Hyper Terminal on Windows). The CD-ROM also
includes some recommended terminal programs.
The factory default login is
Login name: administrator
Password: <empty>
So use the name administrator after the login prompt and simply press the Enter key after the password
prompt.
login:administrator
password:
172.16.40.1>
2

SmartNode™
After you have successfully logged in you are in the operator execution mode, indicated by '>' as command
line prompt. With the commands enable and configure you enter the configuration mode.
172.16.40.1>enable
172.16.40.1#configure
172.16.40.1(cfg)#
Changing the IP Address
Select the context IP mode to configure an IP interface.
172.16.40.1(cfg)#context ip router
172.16.40.1(ctx-ip)[router]#
Now you can set your IP address and network mask for the WAN IP interface eth0. Contact your network
administrator if you are not sure what IP address to set. Within this example a private network (172.16.1.0) is
assumed. The IP address is set to 172.16.1.100.
172.16.40.1(ctx-ip)[router]#interface eth0
172.16.40.1(if-ip)[eth0]#ipaddress 172.16.1.100 255.255.255.0
2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.
2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.
172.16.1.100(if-ip)[eth0]#
Store this modified configuration and make it your new start-up configuration. On the next start-up the system
will come up using the modified configuration.
172.16.1.100(if-ip)[eth0]#copy running-config startup-config
172.16.1.100(if-ip)[eth0]#
Now the SmartNode can be connected to your IP network.
Connect the SmartNode to the Network
You now can connect the SmartNode to the IP Network and do any remaining configuration from any PC
connected to the same Ethernet segment.
3

SmartNode™
You can check the connection with the ping command. For the example above ping 172.16.1.100 from a PC on
the IP network.
You may now start to configure the SmartNode from scratch using the CLI commands. For a detailed
description of the CLI refer to the SmartWare software configuration guide (SCG) available on the CD-ROM
and online at: www.patton.com/voip.
We recommend however that you start your configuration from a template. See step three for further details.
Download a configuration example, adapt to your network and load
onto the SmartNode
We recommend that you use an application specific configuration template called “Application Note” to start
your SmartNode configuration. A selection of Application Notes is available on the CD-ROM and online from
http://www.patton.com/voip/appnotes.shtml. Select an Application Note which matches your requirements.
Adapt the configuration as described in the Application Note to your network (do not forget to modify the IP
address) and copy the modified configuration to a TFTP server. The SmartNode can now load its configuration
from this server.
In this example we assume the TFTP server is running on the PC with the IP address 172.16.1.10 and the
configuration named SN.cfg in the root directory of the TFTP server.
172.16.1.100(cfg)#copy tftp://172.16.1.10/SN.cfg startup-config
Download...100%
172.16.1.100(cfg)#
You now need to reload the SmartNode to activate the downloaded startup configuration. Type in the
following commands.
Note that you MUST answer NO when asked to overwrite the startup configuration.
172.16.1.100(cfg)#reload
Running configuration has been changed.
Do you want to copy the 'running-config' to the 'startup-config'?
Press 'yes' to store, 'no' to drop changes : no
Press 'yes' to restart, 'no' to cancel : yes
The system is going down
Additional Information
For detailed information about configuring and operating guidance, set up procedures and trouble shooting,
refer to the SmartNode Series SmartWare Software Configuration Guide and the SmartNode Hardware Installation
Guide on the enclosed Patton VoIP CD-ROM or at http://www.patton.com/voip/. On the CD-ROM you will
also find numerous freeware and shareware tools, including TFTP servers, Telnet clients, etc.
4

SmartNode™
EC Declaration of Conformity
(German version see below)
Product Description: SmartNode 1200 *)
SmartNode 1400 *)
SmartNode 2300 incl. Interface Cards IC-4BRV and IC-E1V
SmartNode 2400 incl. Interface Cards IC-4BRV and IC-E1V
The products described above in the form as delivered are in conformity with the provisions of the following
European Directive:
R&TTE 1999/5/EC
Guideline of the European Parliament and the Committee for the Harmonisation of the Legal
Regulations of the Member States concerning radio equipment and telecommunications terminal
equipment and the mutual recognition of their conformity.
The safety advices in the documentation accompanying the products shall be obeyed. The conformity
to the above directive is indicated by the CE sign on the device.
*) SmartNodes 1200 Version 5 and SmartNodes 1400 Version 1 (Model No. SN1200 0005-0001 resp. SN1400
0001-0001) must use at least the following Builds of SmartWare: Build 21211 for Release 2.01, Build 21209 for
Release 2.02, Build 21182 for Release, or any Build for all subsequent Releases.
The signed Declaration of Conformity can be downloaded from
http://www.patton.com/certifications/
Approval
The SmartNode is approved for connection to the public ISDN telecommunication network. Anybody may
connect the SmartNode to a BRI/S0- ISDN interface and put it into operation.
EG-Konformitätserklärung
(English version see above)
Produktbezeichnung: SmartNode 1200 *)
SmartNode 1400 *)
SmartNode 2300 inkl. Interface Cards IC-4BRV und IC-E1V
SmartNode 2400 inkl. Interface Cards IC-4BRV und IC-E1V
Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften
folgender Richtlinie überein:
R&TTE 1999/5/EG
Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige
Anerkennung ihrer Konformität.
5

SmartNode™
6
Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten. Die
Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem Gerät bestätigt.
*) SmartNodes 1200 Version 5 und SmartNodes 1400 Version 1 (Model No. SN1200 0005-0001 bzw. SN1400
0001-0001) müssen mindestens folgende SmartWare-Builds verwenden: Build 21211 für Release 2.01, Build
21209 für Release 2.02, Build 21182 für Release, oder irgendeinen Build für alle nachfolgenden Releases.
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von:
http://www.patton.com/certifications/
Zulassung
Der SmartNode ist für die Anschaltung an das öffentliche ISDN Telekommunikationsnetz zugelassen. Er darf
durch jedermann an eine BRI/S0- Schnittstelle angeschlossen und in Betrieb genommen werden.
Legal Notice
Copyright © 2005 Patton Electronics Co
All rights reserved. No part of this publication may be reproduced without prior written permission from Inalp Networks AG. dba Patton-
Inalp AG.
Patton -Inalp AG reserves the right to make changes in specifications and other information contained in this document without prior
notice. The information provided is subject to change without notice.
In no event shall Patton Inalp AG or its employees and associated companies be liable for any incidental, special, indirect or consequential
damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained within
it, even if Patton -Inalp AG has been advised of, known, or should have known, the possibility of such damages.
Patton, the Patton logo, and Inalp SmartNode are trademarks of Patton Electronics Company and Inalp Networks AG. SmartWare and
SmartView Management Center are trademarks of Inalp Networks AG. All other trademarks mentioned in this document are property of
their respective owners.
Document Number: 13216U7-001 Rev. B
Part Number: 07MSN4552-QS
Revised: February 25, 2005