Pawever Pets PPDOGTRNCLA User manual

RECHARGEABLE ANTI BARK
DOG TRAINING COLLAR
PPDOGTRNCLA

 The waterproof feature protects the receiver from getting wet. However, the
receiver cannot be submerged in water for a long period of time. The charging port
must be completely covered when using the receiver in wet environments.
 Misusing the dog training collar may injure your pet. Read the instructions carefully
before using it and contact Kogan.com if you have any questions.
 DO NOT use on puppies younger than 6 months. This product is recommended for
use with medium/large dogs.
 Training collars should be used to help fix behavioural issues, not for punishing/
abusing animals.
SAFETY & WARNINGS

❶ Antenna: Signals transmission
❷ LED light: Press for 10 seconds to turn the light on/off
❸ LCD screen: Shows the modes, levels and channels
❹ Vibration button: Regular vibration button
❺ Intense vibration button: Increased vibration button
❻ Sound/Tone button: Press once to select mode and again to produce sound
❼ "-"Button: Lowers selected level
❽ "+"Button: Raises selected level
❾ Channel button: Press to select a training channel (CH1/CH2/CH3)
❿ Light button: Press to turn remote LED on/off (turns off automatically after 10 seconds)
Press and hold to turn collar LED on/off (turns off automatically after 5 minutes)
⓫ Remote charging port
⓬ Power button: Press to turn receiver on and off
⓭ Receiver charging port
⓮ Rubber caps: Place on top of the touch points to prevent skin damage.
⓯ Indicator: Flashes to confirm vibration/sound and turns on when receiver is charging
OVERVIEW

Charge the remote and receiver before first use for upwards of 5 hours.
 The charging indicators will flash during charging and be solid when charging is
complete.
 The collar cannot receive any signals while it is charging.
 The remote will show a low battery icon when it needs to be charged.
 The receiver’s indicator will flash when it needs to be charged.
 The standby battery life is about a month. Charge the device once a month even if
it is not used to maintain battery health.
Auto Power Saving Function
 The remote will fall into sleep mode after 30 seconds of no interaction. You can
reactivate it by pressing any button.
 If there is no operation within 5 minutes the receiver will fall into standby mode,
which is shown by the unlit indicator light. The receiver can be reactivated once it
is wobbled. You don't need to press any button on the remote or receiver to
reactivate the receiver.
 The receiver can be turned off by pressing the power button on the receiver.
PREPARATION
Tips:
To avoid pressing the wrong button when switching through modes, select the mode by
pressing it once and then press it again to activate it. You can also long press to reselect
the modes (there may be 1
-
2 second delay when switching).

Synchronise the Remote and Receiver
1. Turn on the remote by pressing the vibration button and select one of the signals
by pressing the CH button.
2. Adjust the levels by pressing"+" or"-" button (ensure the level is above 1).
3. Press the power button on the receiver and wait at least 5 seconds: you will hear a
confirmation tone and the indicator light will be flashing.
4. Press the Vibration button within 10 seconds and a tone will sound again to confirm
the pairing is successful.
5. If you have multiple receivers, simply choose a different channel and pair as per the
same instructions.
The remote and receiver(s) should now be paired. Pairing is necessary to control the
receiver.
You should then test each of the functions before attaching the collar to your pet.
 Test the vibration function using the vibration button: the receiver should vibrate.
 Test the sound function using the sound button: the receiver should produce a
tone.
 Test the light function using the light button: the white LED on the receiver should
illuminate.
To attach:
1. Attach the receiver to the collar and place the collar around your pet’s neck.
2. Attach the rubber caps that came with the product to the touch points.
3. Adjust the collar so that a finger can be inserted between the collar and your pet’s
skin but it is not loose.

Know the intensity of each mode
Knowing the intensity of each mode will be helpful to control the stimulation.
Setting the Initial Training Level
To set the initial training level you must first determine the lowest stimulation that will
clearly get your dog's attention by the following steps:
1. Set stimulation at zero.
2. Fit the collar properly on your dog's neck and start the training.
1. If he does not focus on you, begin the stimulation and progressively increase the
levels until he responds to the beep/vibration. If your dog yelps or jumps, this
indicates that the level is too high.
Every dog is individual and unique. Some are more sensitive than others and some learn
more slowly or quickly. Be sure to test out each level on each individual dog.
Stopping Unwanted Behaviours
For this type of training, you need to set the collar at a predetermined stimulation level as
outlined above.
1. Let your dog roam in the area where he might misbehave, for example eating from
the rubbish.
2. Get yourself out of his sight or at a discreet distance and wait.
3. When the dog misbehaves, press the button. This will cause your dog to associate
the signal with his misbehaviour. If he doesn't respond, you can increase the level.
OPERATION
Tips:
Timing is crucial. Catching the unwanted behaviour and sending the signal at the precise
moment can drastically shorten training time.

Reinforcing Learning Behaviours
If your dog knows the command but responds inconsistently or acts slower than your
requirement, a training collar can sharpen his skill.
For example, you have taught your dog to come when called, but over time he responds
slower. You can communicate with him via the remote trainer, so that he immediately
responds to your call.
1. Set the collar to initial stimulation level and test it.
2. Fit the collar on your dog's neck along with his regular collar.
3. Let him roam around the training area. Then give the command and
simultaneously press the stimulation button.
4. The instant your dog moves toward you, stop stimulation and praise him.
5. If he stops before he reaches you or turns away repeat the command and continue
the stimulation. Again, stop at the instant he runs to you and reward him by
praising him or feeding him a treat. Repeat this for 3 or 4 times.
Tips
1. If he doesn't get it for the first few times, don't give up and do not increase the
stimulation. Try to work on this a couple of times per day.
2. During the training period never give the command if you are not able to enforce it.
Your dog has to make the mental connection between the vibration/beep to his
behaviour (may take a week or more for some dogs).
Altogether, both methods of stopping unwanted behaviour and reinforcing learning
behaviours can be applied to nearly every training scenario.
Training collars are used to train the dogs and not for punishment. Use properly and with
care and the collar can be a safe and effective tool to train, build communication and
strengthen your bond with your best friend.

Remote signals are not detected
 Ensure there are no interferences or obstacles between you and your dog.
 Ensure the remote and the receiver are fully charged.
 Ensure the remote and receiver are not in standby mode?
 Avoid switching modes frequently.
 Press the buttons firmly in the centre.
 Charge the receiver and transmitter fully.
 Ensure all the adjustable modes are set above level 1.
 Check the channel and ensure you are on the same channel as the collar it is
paired with.
 Check to see if the metal screw caps are too short; if they are, change them.
 Re-pair the remote and the receiver.
Frequency 433MHz
Transmitter 3.7V
Receiver 3.7V 300ma LIP
TROUBLESHOOTING
SPECIFICATIONS

Need more information?
This is a Quick Start Guide, and we hope that this
has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com