PawHut D06-096V02 User manual

EN_IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
FR_IMPORTANT:A LIRE ATTENTIVEMENT ET À CONSERVER POUR CONSULTATION
ULTÉRIEURE.
ES_IMPORTANTE, LEA Y GUARDE PARA FUTURAS REFERENCIAS.
PT_IMPORTANTE, RETER PARA REFERÊNCIA FUTURA: LEIA ATENTAMENTE.
DE_WICHTIG! SORGFÄLTIG LESEN UND FÜR SPÄTER NACHSCHLAGEN AUFBEWAHREN.
IT _ IMPORTANTE! CONSERVARE IL PRESENTE MANUALE PER FUTURO RIFERIMENTO E
LEGGERLO ATTENTAMENTE.
D06-096V02
IN231000329V01_US_UK

Children have died or been seriously injured when gates are not
securely installed.
• ALWAYS install and use gates as directed using all required parts.
• YOU must install wall cups to keep gate in place.Without wall
cups, child can push out and escape.
• STOP using when a child can climb over or dislodge the gate.
• USE only with the locking mechanism securely engaged.
• NEVER use to keep child away from pool.
• NEVER leave child unattended.
• Intended for use with children between 6 and 24 months.
• Install according to manufacturer’ s instructions.
WARNING
IMPORTANT
• Improper installation could result in the gate becoming unstable
or dislodged from the doorway.
• Base locks are to be used at all times, on both sides of the gate.
• This product will not necessarily prevent all accidents.
• Check the gate regularly to see if all the hardware and mount-
ings are tightened.
• Do not use if any components are missing or damaged.
• STOP using when a pet can climb over or
dislodge the gate.
• Additional or replacement parts should only be obtained from the
manufacturer or distributor.
BEFORE USING PRODUCT
2

D06-096V02 29 - 33.5inch
7cm(2.75in)
Extension
14cm(5.51in)
Extension
With 7cm(2.75in)
81 - 86cm
31.5 - 33.5 inch
No Extension
74 - 79cm
29 - 31 inch

INSTALLING YOUR GATE
Figure 1-1
Locate the (4) threaded spindle rods (B).
Rotate the adjustment wheels along
the threading, eliminating the gap be-
tween the adjustment wheel and the
rubber foot (Figure 1-1).
NOTE You may notice a slight gap be-
tween the gate door latch and the
frame (Figure 1-2).
THIS IS NOT A DEFECT this gate is a
pressure mounted gate and this gap
will disappear once you tighten the
gate in its opening.
DO NOT REMOVE THE ZIP TIE UNTIL
INSTALLATION IS COMPLETE.
(Figure 1-3)
Figure 1-2
Figure 1-3
4

Place the gate in desired opening with
the bottom close to the oor. The dis-
tance between the bottom of the gate
and the oor should be less than 1/8
inch(Figure 2-2).
Once you are satised with the place-
ment of your gate trace the spindle
rods rubber feet onto the surface of
your opening making sure these are
level (Figure 2-3). Then remove the
gate from the opening. Then screw the
4 wall cups to the wall using the screws
(Figure 2-4), or paste the 4 wall cups
using the stickers provided (Figure 2-5).
Figure 2-1
Figure 2-3
Figure 2-5
Insert the threaded spindle rods with
adjustment wheels into the hole on all
four corners of the sides of the gate.
(Figure 2-1)
Figure 2-2
1/8 inch
Figure 2-4
15/64inch
6mm
5

Spanner
Figure 3-3
2.5 inch
Figure 3-4
Figure 3-1
Insert all 4 threaded spindle rods into
the wall cups (Figure 3-1). Tighten the
wheels using the spanner tool. (Figure
3-2 and Figure 3-3) Do not over tighten.
It may be necessary to hold the thread-
ed spindle rods while rotating the ad-
justment wheels to ensure that the
entire unit does not rotate while install-
ing the gate.
NOTE if your door latch is not properly
engaging with the receiving compo-
nent, ensure that your gate is level,
mounted properly and that you have
not over-tightened the adjustment
wheels.
NOTE The gap between the gate and
the wall should not exceed more than
2.5 inch on either side (Figure 3-4 and
3-5)
If the gate has been installed prop-
erly the gap between the door latch
and frame should now be closed
(Figure 3-6)
Figure 3-2
Spanner
Figure 3-5
2.5 inch
3/64 inch
Figure 3-6
6

OPERATING THE DOOR LATCH
To Open - Ensure that the base locks at
the bottom of the gate door are in the
horizontal position (Figure 4-1). Pull the
spring lock away from the easy open
latch while simultaneously lifting the
lock lever upwards (Figure 4-2 and 4-3).
This will release the locking latch from
the gate frame and allow the door to
push or pull open.
To Close - Pull the door shut and
ensure that the door latch on top closes
and then place the lock at the bottom
of the gate down on the side occupied
by the child, Gate will swing both ways
unless one of the swing stops is down.
Gate will not swing at all if both swing
stops are down.(Figure 4-4)
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-1
7

Once the gate is opened,it can close
up automatically and lock up.
When the opening width of the gate is
8 inch, the gate has the function of
Automatic Closing (Figure 5-1).
NOTE When the gate opening width is
greater than 23 inch, the gate will be
normally open.(Figure 5-2)
AUTO CLOSE LOCK
Figure 5-1
8 inch
Figure 5-2
23 inch
USE AT THE TOP OF STAIRS
If the gate is used at the top of
stairs, we recommend the safe
distanced to the 1st step is at
least 16 inch. (Figure A)
Using the wall cups will ax
your gate more rmly in the
doorway or opening.
Figure A
16 inch
8

ADDING A GATE EXTENSION
Remove the top and bottom
threaded spindle rods.(Figure 6-1)
Assemble the gate and extension
as illustrated (Figure 6-2 and 6-3).
Reposition the gate and t in ac-
cordance with the gate tting
instructions.
NOTE: It is preferable to install
any extensions on the hinge side
of the gate.
Figure 6-1
Figure 6-2
Figure 6-3
9

REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels
on each of the (4) threaded spindle rods to depressurize the gate
from its doorway or opening. Then, gently pull or push the gate
free from its doorway or opening.
Periodically check the gate for signs of damage, wear, or missing
components.
Do not use if any part is missing, worn or damaged.
Check the gate regularly to ensure all the hardware and
mountings are tightened. Do not use abrasive cleaners or bleach.
Clean by sponging with warm water and a mild detergent.
CARE AND MAINTENANCE
10

11