pawpail PP1030 User manual

PawPail.com
NEED TO CONTACT US?
844-PAWPAIL (729-7245)
[email protected]
http://www.pawpail.com
1
PawPail Mounting System: User Guide
Thank you for purchasing the world’s best designed pet waste station. If you have questions or need assis-
tance, please do not hesitate to contact us directly via email, phone or chat at PawPail.com.
We respectfully ask for the opportunity to make any problems right before posting negative feedback about
our products or our company. We are committed to 100% customer satisfaction with your shopping experi-
ence and we invite you to share your positive product reviews online to benefit our future customers.
With warmest regards to you and your pets,
This document is provided to familiarize you with the components and use of the PawPail Mounting Sys-
tem.Please read this guide in its entirety before starting assembly. To begin, you will need:
Michael J. Harakal
Founder & CEO
Drill with 5/64” (1.98mm) drill bit
Small Phillips-Head screwdriver
Pliers, locking pliers (ex. VISE-GRIP), adjustable
wrench or a 5.5mm hex nut driver
Appropriate screws, bolts or bands to secure the
Mounting Bracket to your desired surface

PawPail.com 2
CONTENTS
8 ea. M3 (5.5mm) x 10mm screws
8 ea. M3 (5.5mm) hex nuts
1 ea. upper mounting hardware
1 ea. lower mounting hardware
1 ea. PawPail mounting bracket
Remove the basket from inside your PawPail and lay your
PawPail on the ground, with the back of the PawPail facing
you. Identify the 8 pre-formed pilot holes on the back of
your PawPail.
Carefully drill through the PawPail container at each of the
pilot hole sites using a drill with 5/64” (1.98mm) drill bit.
ASSEMBLY
Pilot Holes

PawPail.com 3
Align the upper and lower mounting hardware with
the pilot holes as shown and insert screws using
the screw driver.
Next, flip your PawPail over, open it and secure the hex nuts to each screw
location inside the container using either pliers, a wrench or an M3 (5.5mm)
hex nut driver. It may be necessary to secure the screw head using the screw
driver to prevent it from turning.
ASSEMBLY
Upper mounting
hardware
Lower mounting
hardware
AFFIXING THE MOUNTING BRACKET
Select a stable surface in a well-ventilated area to affix the
Mounting Bracket. The surface must be capable of sup-
porting at least 25 lbs. of loading.
The Mounting Bracket can be secured with screws,
bolts or bands/straps (not included).
The minimum screw/bolt length to be used is 3" although
4"+ is recommended.
The 2 Bolt Holes can accept bolts up to 21/64" diameter
and washers up to M8 or 1/4". 1/4" diameter bolts and
washers are sufficient for most applications.
Bolt holes
Screw holes
Band/strap
channels

PawPail.com 4
SECURING YOUR PAWPAIL
FINAL ASSEMBLY
Ensure the fasteners that you select are long enough to provide adequate fixation to your chosen mounting
surface.
PawPail
15275 Collier Blvd. #201-104
Naples, FL 34119
https://www.pawpail.com
Product Name: PawPail Mounting System
Part Number: PP1030
Align the mounting hardware attached to your PawPail with the
Mounting Bracket as shown and gently lower your PawPail onto
both the lower mounting hardware and through the upper mount-
ing hardware. It may be necessary to slightly depress the quick
release tab.
To remove, depress the quick release tab while lifting your Paw-
Pail to disengage the Mounting System.
The Locking Pin Holes on your PawPail Mounting System allow
for cable locks to be used to prevent tampering or theft. Simply
pass a cable lock through one or both sides of the locking pin
holes to secure your PawPail to the Mounting Bracket. We recom-
mend the Master Lock 14" Cable Gun Lock 99KADSPT
The 4 Screw Holes can accept screws up to 3/16" diameter. #8 deck screws are sufficient for most
applications.
The 2 Band/Strap Channels accept bands/straps up to 7/16" width. For most mounting applications,
an 8" band/strap diameter is sufficient.