PAX IM700 User manual

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

12345 6
Please make sure the following items are included with
your IM700 contactless card reader. If any items are
missing, contact your dealer.
Contents
Product Description
Figure 1: Front view
Figure 2: Back view
LED Indicators
Card Interface
RJ45
USB Type-B SAM Card Cover
Name Quantity
IM700 Contactless Card Reader 1
USB 2.0 A/B cable 1
M4 hex nut 4
IM700 Quick Setup Guide 1
Top
Front
Bottom
Right
Left
Bottom
Figure 3: View from all sides
Installation
1) SAM Card
SAM Card Slot 1
SAM Card Slot 2
Slide the cover to the side to remove it, then open the
mount and insert the card into the slot with the contact
facing down and the clipped edge facing the top right.
Then lock the mount and replace the cover.
2) Device Connection
Figure 5: Connecting the IM700 to an IM300 unit
USB Type B USB Type A
USB Cable
Figure 4: IM700 SAM card slots
The IM700 is linked to an IM300 encrypting PIN pad
through a USB Type B port using a USB cable as shown
in Figure 5. The IM300 both controls and powers the
IM700. Either of the two Type A USB ports on the
IM300 can be used to connect the IM700, do not
connect the IM700 through the Mini-B port.
Instructions
2) Card Detection
1)
Switch off:
Figure 6: IM700 interfacing with a contactless card
Link the IM700 to an appropriate power
terminal via USB or RJ45 (make sure to
have the appropriate voltages and pinouts).
Switching the device on and off
Switch on:
Disconnect the IM700 from the power
terminal it is connected to.
In order for the IM700 to detect and interface with
contactless cards, the user holds a contactless card
with the face of the card roughly 4 cm or less from the
face of the device as shown in Figure 6. The orientation
of the card does not matter so long as it is roughly
facing the front of the device.
3)
•All LEDs being in the off state means that the device
is unpowered or powering up and connecting to a
terminal.
•The yellow LED indicates that the device is processing
payments or other services.
•The green LED indicates that the device has just
finished processing the transaction.
•The red LED indicates that the device has just
encountered an error.
4) Environmental Conditions
Storage Temperature: -30°C~70°C (-22°F~158°F)
Working Temperature: -30°C~70°C (-22°F~158°F)
Relative Humidity: 5%~95% (no condensation)
LED indicators
The different LED indicators show the following states
for the IM700:
Maintenance and Usage
5
1) Do not damage the USB or RJ45 cables; if either are
damaged, seek a replacement.
2) Make sure the terminals of the USB or RJ45 cables
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the
IM700, this may cause serious damage to the device.
4) If repairs are required, please contact a professional
technician instead of attempting them on your own.
5)The IM700 is designed for outdoor use; however,
during normal use its surface should still be keep clear
of dirt and possible liquid contaminants.
6)While the IM700 is designed to resist ingress of dust
and liquids, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the
device away from dust and liquids as much as possible.

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.

Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099 W: www.pax.us
P/N: 200312000000325
PAX TECHNOLOGY LIMITED reserves
the right to change product specifications
without prior notification.
Quick Setup Guide
78 9 10
Manufacturer: PAX Computer Technology (Shenzhen) Co., Ltd.
Address: 4FL, Building #3, Software Park, 2nd Central Science-
Tech RD, High-Tech Industrial Park, Shenzhen, Guangdong, PRC
T: 0755-86169630 F: 0755-86169634
W: www.pax.com.cn
IM700
CONTACTLESS CARD READER
Compliance Statements
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired
operation.
1)
2)
Warning
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
•Reorient or relocate the receiving antenna.
This device complies with Industry Canada license-exempt
RSS standard(s).Operation is subject to the following
two conditions:
INDUSTRY CANADA STATEMENT
this device may not cause interference, and
1)
2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes:
l'appareil ne doit pas produire de brouillage, et
1)
2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui
ont été testées.
The Country Code Selection feature is disabled for
products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est
désactivée pour les produits commercialisés aux États-
Unis et au Canada.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits
set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator & your
body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition
aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé
aaaaaa
do not throw away, requires professional recycling
Class II equipment
for indoor use only
DC voltage
Index of Icons
7
VI energy efficiency marking (level VI)
~ AC voltage
avec un minimum de 20 cm de distance entre la source
de rayonnement et votre corps.