PDMOVIE REMOTE AIR User manual

Quick Start Guide

Welcome to your new REMOTE AIR.

NO Name
Single Channel
(Focus) DualChannels
(Focus,Zoom)
3Channels(Foc
us,Zoom,Iris)
EF MAX
A
Wireless Remote
1
1
1
1
B
Receiver / Motor Controller
1
1
1
1
C
Follow Focus Motor (EF)
1
1
1
Follow Focus Motor (Max)
1
1
2
D
B-type power cord
1
1
1
1
E
USB charging cable
1
1
1
1
F
Motor drive line
1
1
2
3
G
USB Charger
1
1
1
1
Strap
1
1
1
1
I
Antenna
2
2
2
2
J
15/19mm Adapter Ring
2
2
3
4
Hard case
1
1
1
1

BUTTON/
CONNECTION
FUNCTION INSTRUCTIONS
ON/OFF CHANNEL
ON/OFF
Hold for 2 seconds, until display shows up.
CHANGE CHANNEL
Quick Press to change channel
NERVE
FOCUS
NERVE
ZOOM
NERVE
(2 Channel)
IRIS
NERVE
(3 Channel)
Automatic Scan Press and hold for 3 seconds until motor starts
turning
Change Motor
direction
Quick press 5 times
Set Manual A-B
Stop
Set Press twice, First is quick press, second is
hold. At the same time turn the dial.
Cancel
Continue press twice
Record last Manual Restart Remote control, then one short press of
NERVE button
3D Mode
Quick press 10 times only 2 channels)
5V
setting

BUTTON/CONNECTION INSTRUCTIONS
ON/OFF CHANNEL
Hold for 2 seconds, until display shows up.
Quick Press to change channel
ANTENNA Antenna connection
MOTOR Motor connector
REMOTE Wired controller
12 20V 12 20V D-TAP power cable

ADVANCED OPERATIONS :
1、The motor can switch directions depending on the alignment of
the lens.
2、LCD INFO:
1st LINE: FREQUENCY= 2. 4GHZ CHANNEL= Current Channel
2nd LINE: Signal Level= Signal connection. If no response, need to
restart receiver. 3rd LINE: TX= Remote battery level. Normal range =
3.4-4.2V.
3、The First time you turn on the motor it appears still so you need
to do the automatic scan.
Hold the NERVE button for 3 seconds until the motor starts turning,
The automatic scan will begin. After it finishes the motor gear will
stop in the middle point of the range. Then turn the dial full range in
both directions. Repeat this step for dual and triple channel
versions.
4、After calibration, the marking disc can be used with correct
distance information. Use tape and a marker on the disc.
5、To do the manual A-B hard stops, whilst turning the dial press
once to set start and hold to set end. To cancel, press twice.
6、If the same lens is used after powering off, press NERVE button
once.

ATTENTION:
1、Check the correct cables are being used before operation.
2、After a while the motor will heat up, this is normal.
3、The motor is designed for cold weather but will not work under
-20℃.
4、The colder the temperature the more noise the motor will make.
5、When charging the remote, it automatically restarts. When
charge is complete remove the cable and it will automatically shut
down.
6、High temperature may cause oil coming out, this is normal, use
cleaning cloth.
7、The torque of the motor is automatic depending on the lens
when the NERVE has scanned the lens.
8、If it fails to scan, check LEMO connector and reattach.
9、After switching on and there is no signal to the motor, change
channel and retry, if not restart the power to both the Remote and
receiver.

Important
Please read this document, master REMOTE AIR usage,Before you first
use your REMOTE AIR.
Learn more
You can find more information, watch demos, and learn even more
about REMOTE AIR features at www.pdmovie.com/remoteair/.
Support
REMOTE AIR enjoy free upgrade program and one year of hardware
warranty period, you can get these services from PDMOVIE dealer.
Contact
Email:
[email protected]
WEB:
www.pdmovie.com
©2014 Perfect Doctrine Co.,Ltd. All rights reserved.

REMOTE AIR入门指南

欢迎使用圆美道无线跟焦器 REMOTE AIR.

EF MAX
A
1
1
1
1
B
1
1
1
1
C
(EF)
1
1
1
(Max)
1
1
2
D
1
1
1
1
E
1
1
1
1
F
1
1
2
3
G
USB
1
1
1
1
1
1
1
1
I
2
2
2
2
J
15/19mm
2
2
3
4
1
1
1
1

ON/OFF CHANNEL
NERVE
FOCUS
NERVE
ZOOM
NERVE
IRIS
NERVE
AB
AB NERVE
REMOTE AIR
EF
3D
5V
5V

ON/OFF CHANNEL
ANTENNA
MOTOR
REMOTE
12 20V 12 20V

具体操作说明：
1、安装驱动轮与接收器，驱动马达可以正向或反向安装，根据镜头调节环间距和镜头的位置选
择合适的安装方向；
连接接收器的驱动线与电源线,驱动线与电源线的连接端口不同，比较容易区分；
安装接收器与控制器天线，长按两秒ON/OFF键开启接收器与控制器。
2、查看OLED屏显示信息：第一行2.4G（无线网络）, Channel:20（当前频道:20)；短按控制
器CHANNEL键将信号频道调至与接收器同一个频道上；
查看OLED屏第二行SIGNAL LEVEL（信号强度）, 显示数值(参考值:70-100)表示信号已接
通；如果信号没连通或连通后没反应,则重启接收器；
查看OLED屏第三行TX（控制器电量）, 控制器正常电压范围3.4～4.2V；TX显示值低于3.5V
时需及时对控制器进行充电。
3、开机后驱动轮呈静止状态，首次使用必须对镜头进行自动行程检测；
按住控制器NERVE键三秒待镜头转动后松手，REMOTE AIR会自动开始检测镜头总行程，行
程检测完成后，驱动轮停留在镜头中间位置，而控制器转盘需转过中间位置后与接收器信号联
动；(双通道与三通道，需要对每一个通道进行独立的自动总行程检测，操作方式同上）。
4、镜头总行程检测完成后，开始对标记环进行标记，标记环采用磁性吸附的方式自动对位；
使用标记纸粘贴在标记环上，根据镜头行程参数标记出对应的控制器转盘参数。
5、REMOTE AIR可通过连按两下NERVE键手动设置行程（即AB点），
第一下短，第二下长按不放，长按的同时转动控制器转盘设置AB点
后放开NERVE键；
如需撤消，则短按两下NERVE键。
6、与驱动轮的安装方向相对应，REMOTE AIR也可以通过连续
短按五下NERVE键切换驱动轮的旋转方向。
7、重新启动接收器后，假如使用同一镜头且上一次工作时有手动设
置行程，则短按一下NERVE键调用已记忆的行程；
假如已经更换镜头或者没有手动设置行程，则重新对镜头进行
自动行程检测。

注意事项：
1、由于REMOTE AIR部件外壳均采用铝合金材质，接收盒与马达发热属于正常散热现象；
在零下20度以下，有可能出现设备无法正常开机的情况，可以使用暖风等外来温度使机器
温度升高，开机后即可正常使用；
2、关于噪音：温度越低，镜头阻尼越大，驱动轮所需要的动力越大，从而可能产生的声响也
就越大；
3、控制器充电时会自动重启；充电完成拔出充电头时会自动关机，如遇到控制器死机现象，
可用插入充电的方法重新启动控制器；
4、新的驱动马达在高温时有可能渗油，属于正常现象，用清洁布蘸酒精将油渍拭去即可；
5、REMOTE AIR会根据镜头阻尼检测并自动分配镜头所需要的力量，转场时比如从高温转到
低温环境的情况下，镜头阻尼会增大，有可能出现咔咔声等运行不顺畅的现象，需要重新对镜
头进行行程检测；
6、在出现位置不对或者扫描不正常的现象时，有可能是LEMO头接触不良，需检查插头并重
新插过；
7、REMOTE AIR信号频道连通后，而接收器未能正常识别指令，此时将频道切换至新的频道
上，重新接上电源后开机。

重要说明
首次使用无线跟焦器前,请仔细阅读本文稿，掌握REMOTE AIR的使用方法。
了解更多
可以在 http://www.pdmovie.com.cn/REMOTEAIR/上找到更多信息、观看
视频以及了解有关 REMOTE AIR功能的详细信息。
支持
REMOTE AIR享有免费的程序升级和一年的硬件保修期限,这些服务可在圆美
道经销商处获得，或直接联系圆美道科技。
联系方式
Email：
[email protected]
如需技术支持，请随时拔打：
[phone]
[phone]
更多动态，资讯敬请留意官方网站：
www.pdmovie.com.cn
©2014 Perfect Doctrine Co.,Ltd. All rights reserved.