Peak Mobotix T25 Manual

V 1.1.0
Mobotix T25
Set-up with a PEAKnx touch panel
EN

Set-up of a Mobotix door station with a PEAKnx touch panel
Created for use with the following products Compatible door station
Controlpro, Controlmini, YOUVI Mobotix T25
The product names mentioned in this document may be brands or registered trademarks
of their respective owners. These are not explicitly labeled with ”™” or ”®”.
© PEAKnx GmbH
Otto-Röhm-Straße 69
64293 Darmstadt
Germany
www.peaknx.com
[email protected]
Document version: 1.1.0
Date: 09.03.21

Set-up of a Mobotix door station with a PEAKnx touch panel
Contents
Introduction 4
1 Fritzbox Configuration 4
1.1 Setting up the Controlmini/-pro in the Fritzbox 4
1.2 Setting up the Mobotix T25 door intercom in the Fritzbox 4
2 Setting up the Mobotix T25 door intercom 5
2.1 Alternative to step 31 - 36 8
3 Setting up the YOUVI camera module (with Bria Solo Free) 10
4 Technical Support 14
About PEAKnx 15
Page

4
Set-up of a Mobotix door station with a PEAKnx touch panel
Introduction
The following instructions explain how to set up a Mobotix T25 door station with your PEAKnx
touch panel. The communication between the touch panel and the door station is realized
via SIP. Therefore, please make sure that both devices are part of the same network and that
YOUVI has Internet access.
1 Fritzbox Configuration
1.1 Setting up the Controlmini/-pro in the Fritzbox
1. Open the browser, enter “fritz.box” into the address bar and log in to your Fritzbox.
2. Navigate to Telephony > Telephony Devices.
3. Go to “Configure new device”, select the option “Telephone” in the next step and go to
“Next”.
4. Select “LAN/WLAN (IP telephone)”, assign a meaningful name, e.g. “Controlmini” and select
“Next”.
− Enter the username and password for the Controlmini and note them for later use. Be
sure to give a secure password. This means it should not be the same as the user name
nor too short or too easy to guess. We recommend that you use an automatically genera-
ted random password.
5. Confirm the assigned phone number and select “Next”.
6. Select “Accept calls for the following numbers only” and “Next”.
7. You will get an overview, which you can confirm with “Apply”. Press any button on the Fritz-
box to confirm the input for the router.
1.2 Setting up the Mobotix T25 door intercom in the Fritzbox
8. Under Telephony > Telephony Devices, go to “Configure new device” again and in the next
step select the option “Door Intercom System” and “Next”.
9. The connection is made via “LAN/WLAN (IP door intercom)”.
10. Assign a meaningful name for the door intercom and press “Next”.
11. Enter a username and password for the door intercom and note them down.
− Be sure to give a secure password. This means it should not be the same as the user
name nor too short or too easy to guess. We recommend that you use an automatically
generated random password.
12. For “Route doorbells to”, select “Controlmini” from the drop-down list and go to “Next”.
− If this option does not appear in the selection menu, you can also select “telephone
number” and enter the phone number “** xxx” of the Controlmini in the Fritzbox. In this
example, that would be the “** 620”.

5
Set-up of a Mobotix door station with a PEAKnx touch panel
13. You will get an overview, which you can confirm with “Apply”.
2 Setting up the Mobotix T25 door intercom
1. Connect the Mobotix device to a PoE-enabled switch on your network.
2. To be able to set up the Mobotix T25, you must enter its IP address into your browser.
− At fritz.box under Overview > Home network, the active clients/devices are displayed.
Here you will also find the IP address of the door intercom. Enter it in the browser to
reach the configuration page of the door station.
3. The default user name is: “admin”, the password is “meinsm”.
4. Under Admin Menu > Page Administration > Language and Start Page you can set the
languages.

6
Set-up of a Mobotix door station with a PEAKnx touch panel
5. Under Admin Menu > Audio and VoIP Telephony > SIP Client Settings you will find the SIP
settings.
6. After the auto-configuration, Mobotix own SIP server is already entered here.
7. Click on “Add new SIP account”.
8. Under SIP Address “User Name”, enter the name for the door intercom system that you
have assigned to the system in the Fritzbox.
9. Under “Domain”, enter the IP address of the Fritzbox (registrar).
− You can also find your login data and registrar (Registration server) under fritz.box >
Telephony devices, if you edit the created door intercom system and switch to the “Login
data” tab.
10. Under Authentication “User Name” and “Password”, enter the authentication name and the
password which you have assigned for the Mobotix door station in the Fritzbox.
11. Under “Host-Name / Address” enter the IP address of the Fritzbox (registrar).
12. For the “Port” the 5060 is assigned by default in the Fritzbox.
13. Check “Available as Proxy” and “Use as Registrar”.
14. Save the settings with “Set”.
15. When the window has loaded, click the link at the top of the page: “You can view the cur-
rent status and detailed messages of the SIP Client in the SIP Client: Messages, Calls, Status
dialog.
16. The second registration status should now show “successful”.
17. Return via the “Back Arrow” in the upper left corner and click “Close”.
18. Save the settings permanently.

7
Set-up of a Mobotix door station with a PEAKnx touch panel
19. Create a new user under Admin Menu > Audio and VoIP Telephony > Settings for outgoing
calls. Therefore, click “Add new profile”.
20. Enter a suitable name for the panel under “Profile”, e.g. “Controlmini”.
21. Under “Phone Number” enter the number that you have assigned to the panel in the Fritz-
box. In this case “**620”.
22. Under “SIP Proxy”, select the Fritzbox profile that you just created.
23. Click “Add”.
24. Under “Connection Type” select “SIP Audio”.
25. Under “After the message has been sent”, select “Intercom”.
26. Switch the “Camera Remote Control” to “On”.
27. Under “Hangup after” it is best to specify a time between 1 and 2 minutes.
28. Save the settings with “Set”.
29. Now you can test your entries by clicking on the “Test” button at the top of the page.
30. Click on “Close” and save the settings permanently.
31. Under Admin Menu > Video Door Station > Bell Behavior and Video Mailbox you can now
assign the panel to the door station.
32. To display all options, click on “More” at the bottom right.
33. Add the “Controlmini” profile under Set Remote Stations for Door Station “Remote Stations
for Door Station” by selecting “Controlmini” under “Outgoing Call Profiles” and clicking “Add
selected devices”.

8
Set-up of a Mobotix door station with a PEAKnx touch panel
34. Under Call Profiles > Order of Signaling of the Remote Stations select “Add signaling pha-
se”
35. Select the “Controlmini”.
36. Click “Set” and “Close” to save the settings permanently.

9
Set-up of a Mobotix door station with a PEAKnx touch panel
37. To operate the door station with the PEAKnx touch panels, it is necessary to increase the
microphone volume on the panel, depending on the VoIP software used.
Note: If the microphone gain is too high, the transmission may be cut o and the sound quality
may deteriorate.
− To do this, right-click or long-press the loudspeaker icon in the taskbar and select
“Sounds”.
− In the “Recording” tab, select the first microphone.
− In the following menu, you can set the microphone level in the “Levels” tab.
2.1 Alternative to step 31 - 36
If problems should arise when using the door station, it is also possible to create an action
group instead of the settings under Bell Behavior and Video Mailbox. This action group then
triggers a SIP call on your PEAKnx panel when the bell is pressed.
1. To do this, go to Admin Menu > Video Door Station > Bell Behavior and Video Mailbox
and remove the Controlmini as “Remote Stations for Door Station” by clicking on “Remove
remote station”. This renders steps 31 -36 ineective.
2. Click “Set” and “Close” to save the settings permanently.
3. Navigate to Setup Menu > Event Control > Action Group Overview and select “Add new
group”.

10
Set-up of a Mobotix door station with a PEAKnx touch panel
4. Click on the “Edit” button.
5. Under “Event Selection”, select “Internal: Ring”.
6. Click on “Add new action”.
7. Select “Phone Call: Controlmini” as the value of the action.
8. Make sure that the action group is enabled.
9. Click on “Set” and “Close” to save the settings permanently.
3 Setting up the YOUVI camera module (with Bria Solo Free)
To make use of the Mobotix door station’s camera, it needs to be added and set up within
YOUVI Configuration.
1. To add the camera module open YOUVI Dashboard on the panel and select Install Camera
Device. If you do not have a full license yet, you can purchase it in the PEAKnx Shop.
2. Switch to YOUVI Dashboard > Camera Device OR open the configuration page on your PC
in your browser, making sure that the system running the browser is on the same network