Pearl H-1030 User manual

Congratulations on your purchase!
To get optimum performance from your H-1030 / H-1030S Hi-Hat Stand,
please read this Instruction Manual before playing.
H-1030/H-1030S
PEARL HI-HAT STAND
Instruction Manual
Base
Upper Tube
Pull Rod
Rubber Tip
Footboard
Radius Rod
Wing Bolt
Spring Tension
•Adjustment Dial
Hi-Hat Clutch
Die-Cast Joint
Hi-Hat Cup
Wing Nut
StopLock
H-1030S
H-1030

Radius Rod
Hole
Support Casting
Wing Bolt
Fig. 1
Footboard Attachment / Base Assembly
Lay the Base Assembly horizontally on the floor. Squeeze
the Radius Rods together and insert the ends into the
Holes in the Support Casting as shown (Fig.1). Loosen the
Wing Bolt and open the legs. Stand the Base Assembly
vertically and adjust the legs to form a stable tripod. The
Support Casting should be flat on the floor. Tighten the
Wing Bolt to secure.
Wing Bolt
Fig. 2
Fig. 3
Fig. 4
Die-Cast Joint
Upper Tube
Hi-Hat Clutch
Wing Bolt
Pull Rod
BASE
Pull Rod
Pull Rod
Connector
Fig. 3-A
Note
The legs can be swivelled to accommodate multi-pedal
set-ups. Loosen the Wing Bolt and swivel the legs to the
desired position (Fig. 2).
CAUTION
Make sure that the tripod is stable and the Wing Bolt is
securely tightened before playing.
Upper Section Assembly
Remove the Pull Rod from the Upper Tube. Loosen the
Wing Bolt on the Hi-Hat Clutch and remove it from the Pull
Rod. Thread the Pull Rod into the Connector inside the
Die-Cast Joint of the Base as shown and tighten securely
(Fig.3, 3-A).
StopLock
Die-Cast Joint
Upper Tube
Wing Nut
Next, loosen the Key Bolt on the StopLock and insert the
Upper Tube into the Die-Cast Joint. Adjust the height of the
Upper Tube to your preference and tighten the Wing
Nut/Wing Bolt on the Die-Cast Joint. Slide the StopLock
against the Die-Cast Joint and tighten the Key Bolt (Fig.4).

StrongLight
CAUTION
The Base Tube is secured to the Support Casing with an Allen
Screw. Periodically check it for tightness and if it's loose,
tighten it with the provided Allen wrench to restore stability
(Fig.8).
http://www.pearldrum.com
Products and specifications are subject to change without notice.
Printed in China
-1912-
Fig. 5
Hi-Hat Cup Tilt Adjustment
The tilt on the Hi-Hat Cup can
be adjusted by turning the
Knob. Tilting the Hi-Hat Cup
prevents “air lock” between
the cymbals.
Fig. 6
Fig. 7
Knob
Spring Tension
Adjustment Dial
Attaching the Hi-Hat Cymbals
Please have your Hi-Hat Cymbals ready. First, place the
Bottom Cymbal on the Hi-Hat Cup as shown (Fig.5).
Remove the Bottom Lock Nut and one of the Felt Washers
from the Hi-Hat Clutch. Insert the Hi-Hat Clutch into the Top
Cymbal and replace the Felt Washer and the Bottom Lock
Nut as shown (Fig.5-A). Insert the Pull Rod through the
Hi-Hat Clutch as shown (Fig. 5). The distance between the
Top and Bottom Cymbals can be adjusted by stepping on
the Footboard. Tighten the Wing Bolt on the Hi-Hat Clutch
when the desired spacing is achieved.
Hi-Hat Cup
Upper Tube
Hi-Hat Clutch
Top Cymbal Fig. 8
Periodically lightly lube external moving parts such as the
Chain, Wing Nuts, Wing Bolts, Key Bolts and the hinge on the
Footboard.
Allen Screw
Support Casting
Base Tube
Bottom Cymbal
Pull Rod
Top Cymbal
Bottom
Lock Nut
Wing
Bolt
Felt
Washers
Fig. 5-A
Spring Tension Adjustment
The Spring Tension can be adjusted by turning the Spring
Tension Adjustment Dial on the Base. Turn it clockwise to
make it lighter and counterclockwise to make it stronger.