Peavey UA 35T II User manual

SPECIFICATIONS
Output Power:
35 watts RMS
Power Bandwidth:
50 Hz-20 kHz, .8% THD Mic
50 Hz-20 kHz, .6% THD AUX
Frequency Response:
50 Hz-20 kHz +0, -2 dB
50 Hz-20 kHz +0, -2 dB Mic/Page
THD (1 kHz):
Aux <.05%
Mic <.2%
Page <.2%
S/N Ratio (22 kHz BW):
Tone controls flat/input control max:
85 dB Aux
58 dB Mic/Page
Tone Controls:
Bass ± 10 dB @ 100 Hz
Treble ±10 dB @ 10 kHz
Inputs:
AUX Input: Dual RCA phono jacks,
summed
Mic/Page Input: Screw terminal input
switchable between mic/page
Input Sensitivity:
AUX Input: 100 mV @ 10K
Mic Input: 1 mV @ 1K
Page Input: 120 mV @ 5K
Outputs:
4 ohms, 8 ohms, 600 ohms, 25 V, 70 V
Output Regulation:
Less than 0.5 dB, no load to full load
Controls:
1 AUX input gain control, 1 mic/page gain
control, 1 bass control, 1 treble control, 1
mic/page select switch
Indicators:
Power LED
Protection:
Built-in, with AC line fuse
Power Consumption:
120 volts AC, 60 Hz, 100 watts
Dimensions:
4.25" H x 8.25" W x 13.625" D
Weight:
11.5 pounds
Color:
Gray
Other Features:
Mic/Page input has precedence over the
AUX input (defeatable)
FEATURES
¥ 35 watts into 4 ohms
¥ Mic/page inputs (screw
terminals)
¥ Mic/page select switch
¥ Dedicated program input (screw
terminals and RCA jacks)
¥ Bass and treble controls
¥ Mic/page level controls
¥ Direct 4 ohm output (screw
terminal)
¥ Completely isolated 8 ohm, 600
ohm, 25 volt and 70 volt outputs
(screw terminals)
¥ Shelf-top or wall-mount-
able chassis
DESCRIPTION
The UAª35T II is a high quality
utility amplifier ideally suited for
varying installation requirements.
It produces 35 watts into 4 and 8
ohm direct connections plus a
broad range of line amplification.
Level controls are provided for
mic/page and AUX. The AUX input
is accessible via screw terminals
or RCA jacks. Bass and treble
controls are functional on the
total system (mic/page/AUX).
When a signal is present at the
mix/page input, the AUX input is
muted. This feature is internally
defeated when required.
Twenty-five and seventy volt line
output capability is standard
equipment, and the unit is
packaged for shelf or wall mount-
ing convenience. The user-friendly
control layout, coupled with state-
of-the-art circuit design, ensures
reliable long-term operation and
smooth trouble-free installation.
WALL OR SHELF MOUNTING
The UA 35T II can be mounted on
a vertical or horizontal surface
using the brackets formed on the
bottom panel. For mounting on a
wooden or paneled surface, use
No. 6 x 1/2" or larger wood
screws. For mounting onto a
masonry or drywall type surface,
use fasteners that are designed
for this purpose.
SPECIFICATIONS
UAª35T II
Utility Amplifier
¨
ARCHITECTURAL ACOUSTICS ®
UA 35T S/S 2/24/99 3:02 PM Page 1

LIMITED WARRANTY
Peavey Electronics Corporation warrants to the original purchaser of this new Architectural Acoustics product
that it is free from defects in material and workmanship. If within one (1) year from date of purchase a properly installed
product proves to be defective and Peavey is notified, Peavey will repair or replace it at no charge. (Note: Batteries and
patch cords not covered.) ÒOriginal purchaserÓ means the customer for whom the product is originally installed.
Damage resulting from improper installation, interconnection of a unit or system of another manufacturer,
accident or unreasonable use, neglect or any other cause not arising from defects in material and workmanship is not
covered by this warranty. The warranty is valid only as to products purchased and installed in the United States.
THIS LIMITED WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE.
UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS,
INCIDENTAL DAMAGES OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE
THE PRODUCT, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THIS LIMITED
WARRANTY IS THE ONLY EXPRESSED WARRANTY ON THIS PRODUCT, AND NO OTHER STATEMENT,
REPRESENTATION, WARRANTY, OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON
PEAVEY.
Peavey's liability to the original purchaser for damages for any cause whatsoever and regardless of the form of
action, is limited to the actual damages up to the greater of Five Hundred Dollars ($500) or an amount equal to the
purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of
action. This limitation of liability will not apply to claims for personal injury or damage to real property or tangible
personal property allegedly caused by Peavey's negligence. For information on service under this warranty, call a
Peavey customer service representative at [phone].
UA 35T II ARCHITECTURAL
AND ENGINEERING
SPECIFICATIONS
The mixer amplifier shall have one
switchable microphone/paging
channel and one dedicated
auxiliary channel. The mic/page
input will be transformer balanced
and will have the capability to
automatically mute the AUX input.
The master section shall include
two EQ controls providing 10 dB of
boost or cut at 100 Hz and 10
kHz. The unit shall be packaged in
a rugged metal chassis 4.25" tall
by 8.25" wide by 13.625" deep.
Half-inch mounting flanges shall
be provided on each side. The unit
shall operate from 120 volts AC,
60 Hz power. The internal amplifier
shall be capable of delivering 35
watts RMS into 4 ohms and 8
ohms as well as providing 25 volt
and 70 volt line outputs. The unit
shall be capable of delivering
rated power from 50 Hz to 20 kHz
+0, -2 dB into 4 ohms at its 4
ohms output at less than .05%
distortion with system hum and
noise at least 85 dB below rated
power (Aux Input). The unit shall
be a Peavey Architectural
Acoustics Division model UA 35T
II.
TM
¨
¨
ARCHITECTURAL ACOUSTICS ®
Features and specifications subject to change without notice.
Peavey Electronics Corporation / 711 A Street / Meridian, MS 39301 / U.S.A. / [phone] / Fax [phone]
©1997 Printed in U.S.A. 10/97
80304367
UA 35T S/S 2/24/99 3:02 PM Page 2