peerless-AV LCV-100 Guide

ISSUED:11-7-02 SHEET #: 090-9066-8 12-17-13
Visit the Peerless Web Site at www.peerless-av.com For customer service call 1-800-865-2112.
1 of 4
Installation and Assembly - Monitor Desktop Stand Models: LCV-100
LCV-100
IMPORTANT! Read entire instruction sheet before you start installation and assembly.
NOTE: You may not use all hardware provided.
NOTE: Some parts may not appear exactly as illustrated.
G
F
H
E
K
I
J
A
B
C
IMPORTANT! The product is made to support screens with a VESA compliant hole pattern.
For safe mounting, mounting screws must turn at least three times in the screen inserts.
D
LCV-100
Description Qty. Part #
A
mount assembly 1 091-1091
B3mm allen wrench 1 560-0073
Cmounting base 1 091-1089
Dadapter plate 1 095-4354
EM4 x 8mm countersink screw 4520-1795
FM4 x 10mm phillips screw 4520-1796
Gwood screw #14 x 1 4510-9159
Hhex bolt 1 -
Ihex nut 1 -
JM4 x 0.7mm nut 4 530-1082
Kpressure plate 1 -
Parts List
MAX Load Capacity:
25 lb (11.4KG)

ISSUED:11-7-02 SHEET #: 090-9066-8 12-17-13
Visit the Peerless Web Site at www.peerless-av.com For customer service call 1-800-865-2112.
2 of 4
G
DESKTOP
C
C
DESKTOP
H
I
K
Mark hole on desktop for positioning mount.
Drill one 1/2" dia. hole through desktop. Attach
mounting base (C) to desktop using hex bolt (H),
pressure plate (K), and hex nut (I). Tighten nut
using proper sized wrench.
Important! Mount is to be installed onto desktops
3/4" to 1-5/8" thick only! For thicker mounting
surfaces, you may have to provide your own
hardware.
There are two methods of installation. Follow step 2-1 for installation using hex bolt and pressure plate
or step 2-2 using four wood screws.
Use four holes on mounting base (C) to mark holes
on desktop for positioning mount. Drill four 3/16"
dia. holes through desktop. Attach mounting base
(C) to desktop using four wood screws (G).
• Mount must be installed on wood and/or wood composition surfaces of at least 3/4" thick. However, the installer
must ensure that the mounting surface will safely hold the combined weight of the mount and the screen. See other
mounting requirements below.
CAUTION
Remove telescopic pedestal (A) from
mounting base (C) by loosening set screws
where shown with 3 mm allen wrench (B).
SET SCREWS
A
C
2-22-1

ISSUED:11-7-02 SHEET #: 090-9066-8 12-17-13
Visit the Peerless Web Site at www.peerless-av.com For customer service call 1-800-865-2112.
3 of 4
F
A
To install to a VESA 75 mm standard LCD
monitor, attach mount assembly (A) to
back of LCD monitor using four M4 x 10 mm
phillips screws (F) as shown.
Skip to step 6.
F
A
D
A
J
E
GENERIC LCD SCREEN
To install to a VESA 100 mm standard LCD monitor, attach adapter plate (D) to mount assembly (A) using four
M4 x 8 mm phillips screws (E) and four M4 x 0.7mm nuts (J) as shown in detail 1. Attach mount assembly (A) to
back of LCD monitor using four M4 x 10 mm phillips screws (F) as shown in detail 2.
DETAIL 1 DETAIL 2
Insert telescopic pedestal (A) into mounting
base (C). Tighten set screws where shown
with 3 mm allen wrench (B).
SET SCREWS
A
C

ISSUED:11-7-02 SHEET #: 090-9066-8 12-17-13
Visit the Peerless Web Site at www.peerless-av.com For customer service call 1-800-865-2112.
4 of 4
To adjust tilt position, hold the screen with one
hand and loosen the handle as shown in detail 3.
Adjust the screen then tighten handle.
To adjust tilt position of display, turn the triangular shaped knob, adjust display to the desired angle shown in
detail 5 then tighten knob. For screens 15 lbs and over, it may be necessary to tighten set screws with the
3mm Allen wrench (B).
To adjust height position, hold the screen with one
hand and turn the circular knobs counterclockwise
as shown in detail 4. Adjust the screen then tighten
knobs.
DETAIL 4
DETAIL 5
SET SCREWS
DETAIL 3