peerless-AV DS-LEDIF Series User manual

12018-03-14 #:146-9020-4 (2019-05-16)
ENG
DS-LEDIF Series
For Samsung IF015H, IF020H, IF025H
*Actual conguration may vary

22018-03-14 #:146-9020-4 (2019-05-16)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please
call customer care at 1-800-865-2112.
WARNING
3/8"
(10mm)
#
Skip to step.
ENG

32018-03-14 #:146-9020-4 (2019-05-16)
This page intentionally left blank.
ENG

42018-03-14 #:146-9020-4 (2019-05-16)
Parts List
Description
Aleft column
Bright column
Cinside vertical column
Dtop horizontal asy
Ebottom horizontal asy
Ftop vertical spacer
Ghorizontal spacer
HM5 x 8mm socket screw
I#14 x 2.5" wood screw
JM5 square nut (spare)
K3mm allen wrench two-tip T-handle
Lwall plate shim
Mconnector plate
NM5 x 5mm set screw
Obottom vertical spacer
Parts (Before beginning, make sure you have all parts shown below).
ENG
A
B
C
left column
right column
inside vertical column
D
E
top horizontal assembly
bottom horizontal assembly
Refer to parts list included for your specic model.
ENG

52018-03-14 #:146-9020-4 (2019-05-16)
N
I
H
J
M5 x 5mm
set screw
#14 x 2.5" wood screw
M5 x 8mm
M5 square nut
O
L
FG
bottom vertical
spacer
wall plate
shim
top vertical
spacer horizontal
spacer
M
connector
plate
K
3mm allen wrench
two-tip T-handle

62018-03-14 #:146-9020-4 (2019-05-16)
1
Refer to layout drawing included for your
specic model.
ENG

72018-03-14 #:146-9020-4 (2019-05-16)
2-1
Optional: If connecting two top horizontal extrusions,
rst remove inner hook-on brackets.
ENG
Remove and save hardware.
ENG
M5 x 16mm
D
D
2-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
M (4) N (8)
D
K
K
D

82018-03-14 #:146-9020-4 (2019-05-16)
2-4
Optional: If connecting two bottom horizontal
extrusions, rst remove inner hook-on brackets
ENG
Remove and save hardware.
ENG
E
E
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
D
H (2)
D
K
K

92018-03-14 #:146-9020-4 (2019-05-16)
H
2-5
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
N (6)
M (3)
E
E
E
E
2-6
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
K
K

10 2018-03-14 #:146-9020-4 (2019-05-16)
3-1
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING
D
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
2.24"
(57mm)
display tile