peerless-AV DS-S555-3X3 User manual

12014-07-30 #:009-9089-7 (2020-01-14)
ENG
DS-S555-3X3
46" - 55"
(117 - 140 cm)
900 lb
(409 kg)
MAX

22014-07-30 #:009-9089-7 (2020-01-14)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
Display center.
ENG
3/8"
(10mm)
3/8"
(10mm)
ENG - This product is designed to be installed on solid concrete. Hardware is included for solid concrete
installation. Before installing make sure the supporting surface will support the combined load of the equipment
and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product
may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to
safely lift and position equipment. This product is intended for indoor use only. Use of this product outdoors could
lead to product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support
please call customer care at 1-800-865-2112.
WARNING
ENG

32014-07-30 #:009-9089-7 (2020-01-14)
This page intentionally left blank.ENG

42014-07-30 #:009-9089-7 (2020-01-14)
Parts (Before beginning, make sure you have all parts shown below).
Parts List
Part #
Description Qty
Apedestal 2 147-T1426
Bcolumn 2 146-T1131
Cextension 2 145-T1778
Dcover 2 145-T1809
Eside support bracket 4 145-T1807
Fvertical support bracket 6 145-T1806
Gleft adaptor bracket 9 146-1609
Hright adaptor bracket 9 146-1608
Icomputer cover 1 145-T1930
Jcomputer shelf 1 145-T1931
Kdual cross support 3 146-T1905
Lextension adaptor 2 145-T1935
Mcord bracket 4 146-T1321
Nknurled knob 4 560-1160
Ocross support 3 146-T1904
Pplate connections 6 145-T1821
QM8 x 16mm socket button screw 112 520-9527
RM8 square nut 50 530-1066
Scover clip 8 590-0317
TM5 x 10mm type-F, socket pin screw 20 520-1164
Ubar nut 4 146-1319
V1/4" power bit 1 560-0263
W5mm allen wrench 1 560-9640
Xnylon shoulder washer 36 590-2233
YM6 x 12mm socket pin screw 36 520-1050
Z4mm allen wrench 1 560-9646
AA M6 x 35mm screw 8 520-0717
BB rawl bolt #6913 8 5M9-381-H03
CC M8 x 20mm screw 6 520-1754
D (2)
cover
B (2)
column
F (6)
vertical support
bracket
E (4)
side support
bracket
C (2)
extension
A (2)
pedestal H (9)
right adaptor
bracket
G (9)
left adaptor
bracket
ENG

52014-07-30 #:009-9089-7 (2020-01-14)
O (3)
cross support
Z (1)
4mm allen
wrench
I (1)
computer cover
Q (112)
M8 x 16mm
R (50)
M8 square
nut
S (8)
cover clip
T (20)
M5 x 10mm
V (1)
1/4" power
bit
W (1)
5mm allen
wrench
X (36)
nylon shoulder
washer
Y (36)
M6 x 12mm
P (6)
plate
connections
L (2)
extension
adaptor
J (1)
computer shelf
rawl bolt
BB (8)
M6 x 35mm
AA (8)
K (3)
dual cross
support
M (4)
cord
bracket
N (4)
knurled
knob
bar nut
U (4)
CC (6)
M8 x 20mm

62014-07-30 #:009-9089-7 (2020-01-14)
2
1
x2
x2
AA (4)
A
B
TOP VIEW
L
Q (4)
U (2)
Do not fully tighten hardware
W

72014-07-30 #:009-9089-7 (2020-01-14)
3
x2
TIGHTEN
CONNECTING
HARDWARE
C
B
L
W

82014-07-30 #:009-9089-7 (2020-01-14)
1/8"
(3mm) 1/8"
(3mm)
TIGHTEN
CONNECTING
HARDWARE
DISPLAYHEIGHT
DISPLAYHEIGHT
Q (6)
R (4)
F
4
5
x6
x2
W
W
F (3)

92014-07-30 #:009-9089-7 (2020-01-14)
TOP VIEW
S (4)
Dx2
6-2
M (2)
N (2)
6-1
x2
TIGHTEN
CONNECTING
HARDWARE
MN

10 2014-07-30 #:009-9089-7 (2020-01-14)
7
ENG - When installing Peerless mounts on a concrete oor, the oor must be at least 8" thick with a minimum
compressive strength of 2000 psi. Never attach concrete expansion anchors to concrete covered with plaster,
drywall, or other nishing material.
WARNING

11 2014-07-30 #:009-9089-7 (2020-01-14)
BB (8)
47-1
Align base. Mark mounting holes.
ENG
7-2
Drill mounting holes into
supporting surface
(3" (76mm) minimum
depth required).
ENG
3/8"
(10mm)
7-3
Align base. Install using concrete anchors
provided.
ENG
3/8"
(10mm)
55.00"
(1397mm)
55.00"
(1397mm)
ENG Maximum 35 ft • lb (47 N.M.).
3"
(76mm)
3/8"
(10mm)

12 2014-07-30 #:009-9089-7 (2020-01-14)
8-1
8-2
8-3
K
O
Q (4)
Q (4)
R (4)
R (2)
CC (2)
P (2)
x3
x3
x3
W
W
W

13 2014-07-30 #:009-9089-7 (2020-01-14)
9-1
TIGHTEN
CONNECTING
HARDWARE
Cross supports must center on columns.
W
Tighten.
ENG Tighten. ENG
ENG

14 2014-07-30 #:009-9089-7 (2020-01-14)
9-2
TIGHTEN
CONNECTING
HARDWARE
Cross supports must center on colmuns.
W
Tighten.
ENG Tighten. ENG
ENG

15 2014-07-30 #:009-9089-7 (2020-01-14)
TIGHTEN
CONNECTING
HARDWARE
Cross supports must center on columns.
9-3
W
Tighten.
ENG Tighten. ENG
ENG

16 2014-07-30 #:009-9089-7 (2020-01-14)
10
E
E (4)
Q (2)
Q (8)
R (2)
R (8)
W

17 2014-07-30 #:009-9089-7 (2020-01-14)
X
X
11-1
H
G
11-2
Center adaptor brackets
vertically on back of screen.
ENG
H
G
x3
X Y Q
OR
Z
x9
x9
W

18 2014-07-30 #:009-9089-7 (2020-01-14)
12-1
12-2
Must hang displays on bottom row rst. Secure pin
in "locked" position.
Must hang displays on middle row second. Secure
pin in "locked" position.
"LOCKED"
POSITION
"LOCKED"
POSITION
ENG
ENG

19 2014-07-30 #:009-9089-7 (2020-01-14)
12-3
Must hang displays on top row last. Secure pin
in "locked" position.
"LOCKED"
POSITION
12-4
Optional: Insert M5 x 10mm type-F socket pin screws
(T) to lock latches.
T
"LOCKED"
POSITION
Z
x18
ENG
ENG

20 2014-07-30 #:009-9089-7 (2020-01-14)
13
Display adjustment
IN
TILT BACKWARD
OUT
TILT RIGHT
TILT FORWARD
TILT LEFT
SIDE
SIDE
SIDE
TOP
SIDE
TOP
UP DOWN
ROTATE LEFT ROTATE RIGHT
ENG