peerless-AV EPT650 Guide

ISSUED: 01-07-11 SHEET #: 203-9014-4 08-21-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com
Installation and Assembly:
Universal Environmental Tilt Wall Mount for 32" - 60"
(81 - 152cm) Flat Panel Displays
Features:
•Universal display mounting brackets hook onto the wall plate for quick, easy,
and safe installation
•Adjustable up to 15° of forward tilt and up to -5° backward tilt
•Pre-tensioned universal tilt bracket allows for tilt angle adjustment in one easy
motion.
•Optional IncreLok feature offers fixed tilts at -5°, 0°, 5°, 10° and 15° increments
•Includes Sorted-For-You™ fastener pack for installation to wood studs,
concrete and cinder block
•Optional horizontal adjustment of up to 8" (203mm) (depending on display
model) for perfect display placement
Models: EPT650, EPT650-S
Max Load Capacity: 175 lb (79kg)

2 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Double Wood Stud Wall ...................................................................................................................................4
Installation to Solid Concrete or Cinder Block........................................................................................................................5
Installing Tilt Brackets.............................................................................................................................................................6
Mounting and Removing Flat Panel Display...........................................................................................................................8
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
•drill
• 5/16" (8mm) bit for concrete and cinder block wall
• 5/32" (4mm) bit for wood stud wall
• level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Due to outdoor environmental conditions such as strong wind gusts, heavy snow, hail, rain, etc., the environmental
mount and hardware, must be inspected at least once a year, and immediately following any time winds exceed
90 mph. A qualified installer or inspector must check for signs of rust, loose fasteners, bent metal, etc. If evidence
of excessive wear, deterioration or any unsafe condition is observed, this product must be taken out of service
immediately. Direct all inquiries to customer care if you have any questions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product was designed for use with other outdoor products only.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional (not evaluated by UL)
WARNING

3 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
DE
ABC
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
F
EPT650 EPT650-S
Description Qty. Part # Part #
Awall plate 1061-T1378 061-7378
Bleft tilt bracket 1 061-T1556 061-7556
Cright tilt bracket 1 061-T1557 061-7557
D#14 x 2.5" wood screw 4520-5033 520-5033
Econcrete anchor 4 590-0320 590-0320
F4mm allen wrench 1 560-1727 560-1727
Parts List
Non-Security Tilt Bracket Fasteners
M4 x 12 mm (6)
(520-0657) M5 x 12 mm (4)
(520-0659) M8 x 16 mm (6)
(520-0663)
M6 x 30 mm (4)
(520-0666)
M6 x 12 mm (4)
(520-0661) M6 x 25 mm (4)
(520-0662)
M6 x 20 mm (4)
(520-0665)
multi-washer (6)
(580-1036)
M4 x 25 mm (4)
(520-0658)
M5 x 25 mm (4)
(520-0660)
M8 x 40 mm (4)
(520-0664)
M8 x 25 mm (4)
(520-0667)
.5" spacer (4)
(540-1057) .75" spacer (4)
(540-1059)

4 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The
top mounting slots should be located 6.2" (157mm) above the desired display center as shown in figure 1.1.
Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud
centerlines. Drill four 5/32" (4mm) dia. holes 2.5" (64mm) deep. Make sure that the wall plate is level, secure it
using four #14 x 2.5" wood screws (D) as shown in figure 1.2.
NOTE: Wall plate may be mounted up to 4" (102mm) off center as shown in figure 1.1.
Skip to step 2.
1
fig. 1.1
CS = center of display
A
STUD
DA
fig. 1.2
CS
6.2"
(157Mm)
4"
(102mm)
4"
(102mm)
Installation to Double Wood Stud Wall
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
WARNING

5 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
1
3
2
E
Drill holes and insert anchors (E).
Place plate (A) over anchors (E) and secure with screws (D).
Tighten all fasteners.
A
E
D
concrete
surface
Make sure that wall plate (A) is level, use it as a
template to mark four mounting holes. The top
mounting slots should be located 6.2" (157mm)
above the desired display center as shown in figure
1.1 on page 4. Drill four 5/16" (8mm) dia. holes to
a minimum depth of 2.5" (64mm). Insert anchors
(E) in holes flush with wall as shown (right). Place
wall plate over anchors and secure with #14 x 2.5"
screws (D). Level, then tighten all fasteners.
solid concrete cinder block
1
Installation to Solid Concrete or Cinder Block
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate wall
plate
plaster/
drywall plaster/
drywall
concrete concrete
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly
to load-bearing concrete.
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable (not
evaluated by UL), the finishing surface must be
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8" (16mm), custom fasteners must be supplied by
installer (not evaluated by UL).
WARNING
D
A
E

6 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
To prevent scratching the display, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. If display has knobs on the back, remove them to allow the adapter brackets to be at-
tached. Place adapter brackets (B or C) on back of display, align to holes, and center on back of display as shown
below. Attach the adapter brackets to the back of the display using the appropriate combination of screws, multi-
washers, and spacers as shown in figure 2.1 or 2.2.
NOTE: For flat back displays proceed to step 2-1. For bump-out or recessed back display skip to step 2-2.
NOTE: "X" dimensions should be equal.
CENTER BRACKETS
VERTICALLY ON BACK
OF DISPLAY
X
X
TILT LOCKING SCREWS
FACE OUT
2
Notes:
• The number of fasteners used will vary,
depending upon the type of display.
• Multi-washers and spacers may not
be used, depending upon the type of
display.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MEDIUM HOLE FOR M5 SCREWS
SMALL HOLE FOR M4 SCREWS
LARGE HOLE FOR M6 SCREWS
MULTI-WASHER
Installing Tilt Brackets
NOTE: Top and bottom mounting holes on display must be used for attaching brackets.
NOTE: Be sure to attach tilt brackets with tilt locking screws facing outward as shown below. Verify that all holes
are properly aligned, and then tighten screws using a phillips screwdriver.
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening
can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to
become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
B
C

7 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
If you have any questions, please call Peerless customer care at 1-800-865-2112.
If you have any questions, please call Peerless customer care at 1-800-865-2112.
Begin with the shortest length screw, hand thread through multi-washer and tilt bracket into display as shown
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over
tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of display.
Begin with longer length screw, hand thread through multi-washer, tilt bracket and spacer in that order into display
as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not
over tighten. If screw cannot make three full turns into the display, select a longer length screw from the baffled
fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.
For Flat Back Display
For Bump-out or Recessed Back Display
2-1
2-2
TILT BRACKET
(Bor C)
DISPLAY fig. 2.1
MULTI-WASHER
SCREW
DISPLAY
MULTI-WASHER
SCREW
TILT BRACKET
(Bor C)
fig. 2.2
SPACER

8 of 26 ISSUED: 01-05-11 SHEET #: 203-9014-4 08-21-12
© 2012, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerless-av.com
DETAIL 2
fig 4.1
IncreLok™
TILT
LOCKING
SCREW LOCATOR
HOLE
TILT
POSITION
HOLES
fig 3.2
SAFETY/
SECURITY
SCREW
CROSS SECTION
DETAIL 1
A
B,C
B,C
A
fig 3.1
Mounting Display: Slowly hook tilt brackets
(B,C) onto wall plate (A) and swing display down
as shown in fig. 3.1. Tilt bracket hooks must fully
engage wall plate as shown in detail 1. Using
the security allen wrench (F), turn safety/security
screws on tilt brackets (B,C) clockwise till screw
tip securely contacts wall plate as shown in cross
section.
Optional Security: Place a padlock with a shackle
dia. of 1/4" (6.35mm) (not supplied) through both
holes in tilt bracket (Bor C) for added security.
Display Adjustment: Display can be adjusted
horizontally by loosening safety/security screws on
tilt brackets (B,C) three full turns. Adjust display as
shown in figure 3.2. Tighten safety/security screws
on tilt brackets till screw tip securely contacts wall
plate as shown in cross section.
Removing Display: To remove display from mount,
loosen safety screws, swing display away from
mount, and lift display off of mount.
3
NOTE: Choosing and setting tilt position may be
easier before placing display onto wall mount.
INCRELOK™:The display can be locked into a
pre-set tilt position of -5°, 0°, 5°, 10°or 15°. Use
locator hole to find tilt position hole and tilt display
to align holes. Tighten IncreLok™ tilt locking
screws on both tilt brackets to lock tilt as shown in
detail 2.
Mounting and Removing Flat Panel Display
Adjusting the Tilt Angle of the Flat Panel
Display
• Always use an assistant or mechanical lifting equipment
to safely lift and position the flat panel display.
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
• Be careful not to pinch fingers when pushing display from
the bottom.
WARNING
4

Instalación y ensamblaje:
Soporte universal de pared de inclinación Ambiental de
montaje para 32 "- 60" (81 - 152 cm) pantallas de panel plano
Características:
• Los soportes universales de montaje para pantallas se
enganchan a la placa de pared para proporcionar una
instalación rápida, fácil y segura
• Inclinación ajustable hacia delante de hasta 15° y hacia atrás
de hasta -5°
• El soporte inclinable universal preapretado permite ajustar el
ángulo de inclinación con un solo movimiento sencillo
• La función opcional IncreLok™ ofrece ángulos de inclinación
predeterminados en incrementos de -5°, 0°, 5°, 10° y 15°
• Incluye el paquete de sujetadores Sorted-For-You™ para
instalaciones en montantes de madera, concreto y bloques de
hormigón de escorias
• Ajuste horizontal opcional de hasta 8" (203mm) (dependiendo
del modelo de la pantalla) para la colocación perfecta de la
pantalla
Modelos: EPT650, EPT650-S
PUBLICADO: 01-07-11 HOJA #: 203-9014-4 08-21-12
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerless-av.com
Máxima capacidad de carga: 175 lb (79kg)

10 de 26 PUBLICADO: 01-07-11 HOJA #: 203-9014-4 08-21-12
Español
Contenido
Lista de piezas......................................................................................................................................................................11
Instalación en una pared con montantes de madera dobles............................................................................................... 12
Instalación en una pared de concreto macizo o de bloques de hormigón de escorias....................................................... 13
Instalación de los soportes inclinables................................................................................................................................ 14
Instalación y desinstalación de la pantalla plana ................................................................................................................ 16
Herramientas necesarias para el ensamblaje
•localizador de montantes (se recomienda uno de "borde a borde")
• destornillador phillips
• taladro
• broca de 5/16" (8mm) para paredes de concreto y de bloque de hormigón de escorias
• broca de 5/32" (4mm) para paredes con montantes de metal o de madera
• nivel
NOTA: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las
advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un cliente
internacional, por favor, comuníquese con su distribuidor local.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga experiencia en
construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Debido a las condiciones ambientales de exteriores como fuertes ráfagas de viento, nieve intensa, granizo, lluvia, etc.
La caja ecológica, junto con su soporte, tubo de extensión y tornillería, se deben inspeccionar cuando menos una vez al
año e inmediatamente después de cualquier ocasión en que los vientos excedan de 90 mph. Un instalador o inspector
calificado deberá revisar que no haya signos de corrosión, fijadores sueltos, metal doblado, etc. Si hay señales de
desgaste excesivo, deterioro o cualquier condición insegura, inmediatamente deberá de retirar de servicio este producto.
Si tiene alguna pregunta, diríjase al servicio a clientes.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los fijadores y
componentes.
• Nunca sobrepase la máxima capacidad de carga. Vea la página 9.
• Si va a instalar el producto en una pared con montantes de madera, asegúrese de que los tornillos de montaje estén
anclados en el centro de los montantes. Se recomienda utilizar un localizador de montantes de "borde a borde".
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo con
más seguridad.
• Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede disminuir
significativamente su fuerza de fijación.
• Este producto fue diseñado para su uso con otros productos al aire libre.
• Este producto fue diseñado para ser instalado en paredes con la siguiente construcción solamente:
CONSTRUCCIÓN DE LA PARED ACCESORIOS NECESARIOS
• Montante de madera Incluido
•Viga de madera Incluido
•Concreto macizo Incluido
•Bloque de hormigón de escorias Incluido
•Ladrillo Comuníquese con un profesional calificado (no evaluados por UL)
•¿Otra superficie o no está seguro? Comuníquese con un profesional calificado (no evaluados por UL)
ADVERTENCIA