peerless-AV DS-LEDF Series User manual

12016-10-28 #:146-9007-3 (2019-06-10)
ENG
DS-LEDF
Series
*Actual conguration may vary

22016-10-28 #:146-9007-3 (2019-06-10)
To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
1
2
+1/2
4
3
Symbols
ENG
WARNING
ENG
x3
Screws must get at
least three full turns
and t snug.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.
Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to
product failure or personal injury. Be careful not to pinch ngers when operating the mount. For support please
call customer care at 1-800-865-2112.
WARNING
4mm
Do not overtighten screws.
ENG

32016-10-28 #:146-9007-3 (2019-06-10)
Parts (Before beginning, make sure you have all parts shown below).
ENG
Parts List
Part #
Description Qty
A corner bracket kit KIT-LED001-3
corner bracket asy 1
B wall plate bracket kit KIT-LED003-3
wall plate asy 1
wood screw 1
C extrusion connector kit KIT-LED004A-2
extrusion connector asy 1
Dframe anchor kit KIT-LEDWP01
frame anchor 2
wood screw 2
E corner adaptor kit KIT-LEDADP-XXXA-2
top corner bracket asy 2
bottom corner bracket asy 2
screw 4
washer (optional) 4
F side adaptor kit KIT-LEDADP-XXXB-2
outer bracket 1
screw 1
washer (optional) 1
G top center adaptor kit KIT-LEDADP-XXXC-2
top center bracket asy 1
screw 2
washer (optional) 2
Hbottom center adaptor kit KIT-LEDADP-XXXD-2
bottom center bracket 1
screw 2
washer 2
Ihorizontal spacer kit KIT-LEDSPR-XXX
outside spacer 2
inside spacer 2
J extrusion kit KIT-LEDEXTXXX

42016-10-28 #:146-9007-3 (2019-06-10)
E
corner adaptor
kit
D
frame anchor
kit
B
wall plate
bracket kit
A
corner bracket
kit
C
extrusion
connector kit
G
top center
adaptor kit
I
horizontal
spacer kit
F
side adaptor kit
H
bottom center
adaptor kit
J
extrusion kit

52016-10-28 #:146-9007-3 (2019-06-10)
1
Refer to layout drawing included for your
specic model.
ENG

62016-10-28 #:146-9007-3 (2019-06-10)
2-1
ENG Channel nut must start
in vertical position.
ENG Tighten screw to lock
channel nut.
Insert corner brackets into extrusion and tighten
screw to lock channel nut in place.
ENG
Left and middle columns
ENG
4mm A (2)
J

72016-10-28 #:146-9007-3 (2019-06-10)
2-2
ENG Channel nut must start
in vertical position.
ENG Tighten screw to lock
channel nut.
Insert corner brackets into extrusion and tighten
screw to lock channel nut in place.
ENG
Right column
ENG
4mm A (2)
J

82016-10-28 #:146-9007-3 (2019-06-10)
3
Optional: Use extrusion connector if provided.
ENG
Tighten connecting hardware.
J
J
C
4mm

92016-10-28 #:146-9007-3 (2019-06-10)
4-1
Tighten corner bracket hardware.
ENG
4mm
Secure right vertical column onto both horizontal
columns.
ENG
J

10 2016-10-28 #:146-9007-3 (2019-06-10)
4-2
Slide on wall plates in between vertical
extrusions. Refer to layout drawing included with
your model for appropriate spacing.
ENG
Tighten connecting hardware.
ENG
B
B
4mm