peerless-AV DS-LEDBXT Series User manual

12020-03-23 #:146-9049-4 (2020-07-15)
DS-LEDBXT Series
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22020-03-23 #:146-9049-4 (2020-07-15)
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
2.5mm
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING

32020-03-23 #:146-9049-4 (2020-07-15)
This page intentionally left blank.
ENG

42020-03-23 #:146-9049-4 (2020-07-15)
A B C
left column right column inside column
Parts (Before beginning, make sure you have all parts shown below).
ENG
D
E
top horizontal asy
bottom horizontal asy
N
M5 x 8mm
M
wall plate
shim
J
horizontal
spacer
L
extrusion
connector
K
vertical spacer
#14 x 1.75"
wood screw
PO
M5 x 5mm
set screw
Q
3mm allen wrench
two-tip
Parts List
Description
Aleft column
Bright column
Cinside column
Dtop horizontal asy
Ebottom horizontal asy
Ftop left horizontal asy
Gtop right horizontal asy
Hbottom left horizontal asy
Ibottom right horizontal asy
Jhorizontal spacer
Kvertical spacer
Lextrusion connector
Mwall plate shim
NM5 x 8mm
OM5 x 5mm set screw
P#14 x 1.75" wood screw
Q3mm allen wrench two-tip

52020-03-23 #:146-9049-4 (2020-07-15)
F G
H I
top left
horizontal asy
top right
horizontal asy
bottom left
horizontal asy
bottom right
horizontal asy

62020-03-23 #:146-9049-4 (2020-07-15)
1-1
Optional: If connecting two top horizontal extrusions,

ENG
Remove and save hardware.
ENG
D,F
D,G
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
L (4) O (8)
2.5mm
D,G
D,F
Q

72020-03-23 #:146-9049-4 (2020-07-15)
2-1
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
E,I
E,H
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
D,G
D,F
Q
Q

82020-03-23 #:146-9049-4 (2020-07-15)
E,I
E,I
E,H
E,H
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
O (6)
L (3)
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
2.5mm
Q

92020-03-23 #:146-9049-4 (2020-07-15)
3-1
Use a laser level to keep mounting holes
level.
ENG
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING

10 2020-03-23 #:146-9049-4 (2020-07-15)
3-2
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
E,G
display tile
1.25" (32mm) minimum
for mounting clearance
2.75"
(70mm)