peerless-AV HT642-004 Guide

Model: HT642-004
Installation and Assembly:
Tilt Wall Mount with Component Storage Capability
Max Load Capacity: 80 lb (29 kg)
ISSUED: 09-21-11 SHEET #: 125-9245-1

Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
• drillwith1/4"and5/32"drillbits
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Metal Stud Wall ................................................................................................................................................5
Installation to Solid Concrete and Cinder Block Wall .............................................................................................................6
Attaching Adapter Brackets to Screen........................................................................................................................ 7 AND 8
Attaching Mounting Bracket Using Hook On Option...............................................................................................................9
Attaching Mounting Bracket Using Tilt Option ..................................................................................................................... 10
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerlesscustomerserviceat1-800-729-0307.
• Thisproductshouldonlybeinstalledbyaqualiedprofessional.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
ware and components.
• NeverexceedtheMaximumLoadCapacityof80 lb (29 kg).
• Ifmountingtowoodwallstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useof
an"edgetoedge"studnderishighlyrecommended.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• Thisproductwasdesignedandintendedtobemountedtothefollowingsupportingsurfacescheckedbelowwith
thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative
supporting surface, contact Peerless customer care at 1-800-865-2112.
• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
xWood Beam None
xSolid Concrete None
xCinder Block None
xMetal Stud None
Brick Contact Customer Service
Other or unsure? Contact Customer Service
WARNING

3 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
AB
Some parts may appear slightly different than illustrated.
Before you start make sure all parts listed are included with your product.
F
CD E
G
H I J K
LMNO
Description Qty. Part #
Arightadapterbracket 1 201-1943
Bleft adapter bracket 1 201-1942
Cwall plate 1 201-1940
DM4 x 12 mm socket serrated washer head screw 4 510-1079
EM6 x 16 mm socket pin screw 4 520-1132
Ftoggler 4 560-9708
G18"long4mmallenwrench 1 560-1727
H1/4-20x23/4"socketpinscrew 4 520-1580
I#14x2.5woodscrew 4 5S1-015-C03
JM5 x 12 mm socket pin serrated washer head screw 6 510-1064
Kconcreteanchor 4 590-0320
L# 8 washer 4 540-1001
Mdual lock 4 600-1009
NM8 x 10 mm socket pin screw 4 520-1706
Onylonshoulderwasher 4 590-2233
PARTS LIST

4 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
C
I
Installation to Wood Stud Walls
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Based on its edges, draw a vertical line down the stud's center. Place wall plate (C) on wall as a template. Mark
thecenterofthefourmountingholes.Drillfour5/32"(4mm)dia.holes2-1/2"(65mm)deep.Securewallplate(C)
towoodstudusingfour#14x2-1/2"woodscrews(I) as shown. Skip to Step 2 page 7
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
1

5 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
Installation to Metal Stud Walls
Rotate toggler (F)
clockwise to wedge it
against inside walls
of metal stud.
Push into hole.
Pivot end of
toggler (F).
Slide plastic cap
forward while pulling
backrmlyonring.
Break off excess.
FOR METAL STUD WALLS ONLY:Drillfour1/2"
(13mm)dia.holesthroughdrywallandstudsatlo-
cations corresponding to wall plate. Insert togglers
(F) as shown below...
Skip to Step 2 page 7
F
Align wall plate with
hole in wall and
fasten with 1/4-20 x 2
3/4"screw(H) using
18"long4mmallen
wrench (G).
wall plate
H
• Productmustbemountedthroughdrywallthathasa
minimumthicknessof1/2"andintometalstuds,26
gauge or heavier.
• Makesurethattogglersareanchoredintothecenter
ofthestudsasshowningure1.Theuseofan
"edgetoedge"studnderishighlyrecommended.
WARNING
H
C
F
STUD
1-1
1-2
1-3
1-4
1-5
1
1-6
Skip to Step 2
g.1

I
K
g1.4
CINDER BLOCK
SOLID CONCRETE
C
6 of 10 ISSUED: 09-21-11 SHEET #: 125-9245-1
Installation to Solid Concrete or Cinder Block
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8"(35mm)ofactual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
inasolidpartoftheblock,generally1"(25mm)minimumfromthesideoftheblock.CinderblockmustmeetASTM
C-90specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhardware
and components.
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
K
Drill holes and insert anchors (K).
Place plate (C) over anchors (K) and secure with screws (I).
Tighten all fasteners.
C
K
I
concrete
surface
• Tightenscrewssothatwallplateisrmlyattached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Alwaysattachconcreteexpansionanchorsdirectly
to load-bearing concrete.
• Neverattachconcreteexpansionanchorsto
concrete covered with plaster, drywall, or other
nishingmaterial.Ifmountingtoconcretesurfaces
coveredwithanishingsurfaceisunavoidable(not
evaluatedbyUL),thenishingsurfacemustbe
counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when
tightening screws. If plaster/drywall is thicker than
5/8"(16mm),customfastenersmustbesupplied
by installer (not evaluated by UL).
WARNING
Make sure that wall plate (C) is level, use it as a
template to mark four mounting holes. The top mounting
holeshouldbe2.5"(64mm)abovethedesiredscreen
centerasshowningure1.1onpage4.Drillfour5/16"
(8mm)dia.holestoaminimumdepthof2.5"(64mm).
Insert anchors (K)inholesushwithwallasshown
(right). Place wall plate over anchors and secure with
#14x2.5"screws(I). Level, then tighten all fasteners.

7 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
BACK OF DISPLAY
200 mm x 100 mm HOLE
PATTERN SHOWN ABOVE
2
7.87"
(200mm)
.98"
(25mm)
7.87"
(200mm)
BACK OF DISPLAY
D
MOUNTING HOLE LOCATIONS
A
B
DISPLAY
Attaching Adapter Brackets to Display
DETAIL 1
L
Using information provided in detail 1 secure adapter brackets (A and B) to back of display using four
M4 x 12 mm socket pin screws (D), with #8 washers (C) using18"long4mmallenwrench(G) as shown below.
NOTE: Make sure that screws are centered in hole in adapter brackets.
Skiptostep3
Attaching Adapter Brackets using VESA 200 x 100 Mounting Pattern

8 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
BACK OF DISPLAY
E or N
O
NOTE: When using M6 x 16
socket pin screw (E), you
must use nylon washer (O).
MOUNTING HOLE LOCATIONS
AB
DISPLAY
DISPLAY
3
Using information provided in detail 1 secure two adapter brackets (A and B) to back of display with four M6 x 16
mm socket pin screws (E) and nylon shoulder washers (O), or four M8 x 10 mm socket pin screws (N) using18"
long 4 mm allen wrench (G).
NOTE: Make sure that screws are centered in hole in adapter brackets.
Attach dual lock (M) to back of adapter brackets (A and B) as shown below.
Attach component to dual lock as shown.
COMPONENT
NOTE: MAKE SURE THAT
COMPONENT CABLES
RUN AS SHOWN
2
Attaching Component to Adapter Brackets
Attaching Adapter Brackets using VESA 200 x 200 Mounting Pattern

9 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
MOUNTING SURFACE
NOT SHOWN FOR CLARITY
Position slots of adapter plates (A and B) onto the
four M5 x 12 mm serrated washer head socket pin
screws (J) attached to wall plate (C).
To secure wall plate (C) to adapter plates (A and B), attach two M5 x 12 mm serrated washer head socket pin
screws (J) through the slots on the sides of wall plate (C) and threaded holes of adapter plates (A and B). Tighten
with the 4 mm security allen wrench (G).
Attach four M5 x 12 mm serrated washer head
socket pin screws (J) to the holes on the sides of
wall plate (C) using the 4mm security allen
wrench (G)provided.
4
Attaching Mounting Bracket Using Hook On Option
4-1
J
C
J
A and B
SLOT J
A
B
C
4-2
BOTTOM OF DISPLAY J
J
C

10 of 10 ISSUED: 09-20-11 SHEET #: 125-9245-1
Attach two M5 x 12 mm serrated washer head
socket pin screws (J) to the bottom holes on the
sides of wall plate (C) using the 4mm security allen
wrench (G)provided.
Position slots of adapter brackets (A and B) onto
the two M5 x 12 mm serrated washer head socket
pin screws (J) attached to wall plate (C).
44-1
J
C
J
A and B
SLOT
C
Attaching Mounting Bracket Using Tilt Option
To secure wall plate (C) to adapter plates (A and B), adjust tilt as desired and attach two M5 x 12 mm serrated
washer head socket pin screws (J) into the slots on the sides of wall plate (A) and threaded inserts of adapter
brackets (A and B). Tighten with the 4 mm security allen wrench (G).
4-2
J
J
MOUNTING SURFACE
NOT SHOWN FOR CLARITY
BOTTOM OF DISPLAY
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
A
B
C