Pentair INTELLICHLOR IC15 User manual

IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
KEEP OUT OF REACH OF CHILDREN
INTELLICHLOR®
SALT CHLORINE GENERATOR
MODEL IC15, IC20, IC40, IC60
INSTALLATION AND
USER’S GUIDE
http://waterheatertimer.org/Intermatic-control-centers-and-manuals.html
http://waterheatertimer.org/How-to-control-intellichlor.html

Salt is an inherently corrosive material. While the levels of salt required for proper operation of the IntelliChlor Salt
Chlorine Generatorr (SCG) are relatively low when compared to sea water and other salt solutions, placing any
amount of salt in your pool increases the likelihood of corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Metal parts (including metal pools) and certain natural and man-made
surfaces are particularly susceptible to corrosion and deterioration when used in and around salt water pools.
Pentair Water Pool and Spa, Inc. (“Pentair”) does not represent or otherwise guarantee that the proper use of
the (SCG) will prevent corrosion or other deterioration of pool equipment and any surfaces used in and around
your pool. Consult your experienced pool professional, who should be able to advise you on the proper material
selection, installation techniques for those materials, and the proper use, care and maintenance of those materials
for your specic pool type and location in order to minimize the corrosion and deterioration that is inherent in and
around salt water pools.
All Pentair trademarks and logos are owned by Pentair or one of its global affiliates. Pentair Aquatic Systems®, IntelliChlor®, EasyTouch®, IntelliTouch®,
SunTouch®, Rainbow™ and Eco Select® are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies
in the United States and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in this document are not
used to indicate an affiliation or endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc. Those names and
brands may be the trademarks or registered trademarks of those third parties. Because we are continuously improving our products and services,
Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.
© 2016 Pentair Water Pool and Spa, Inc. All rights reserved. This document is subject to change without notice.
P/N 520589 Rev. N 2/2016
If you have questions about ordering Pentair Water Pool and Spa replacement parts, and pool products,
please contact:
CUSTOMER SERVICE / TECHNICAL SUPPORT
Customer Service and Technical Support, USA
8 A.M. to 7:30 P.M
Phone: [phone]
Fax: [phone]
Web site
Visit www.pentairpool.com or www.staritepool.com
Sanford, North Carolina
Phone: [phone]
Fax: [phone]
Moorpark, California
Phone: [phone] (Ext. 5591)
Fax: [phone]

i
IntelliChlor Electronic Chlorine Generator Installation and User’s Guide
Contents
Important Warnings and Safety Instructions ................................................................................. iii - iv
Technical Support ....................................................................................................................................... ii
IntelliChlor Salt Chlorine Generator (SCG) Overview ................................................................................1
IntelliChlor SCG Models .............................................................................................................................2
IntelliChlor SCG Control Panel and Cell Description ..................................................................................2
System Components ..................................................................................................................................2
IntelliChlor SCG IC20, IC40, IC60 Power Center .......................................................................................3
IntelliChlor SCG IC15 Power Supply ..........................................................................................................3
System Schematic Diagram .......................................................................................................................4
Install Chlorine/Bromine Feeders after the IntelliChlor SCG cell ...............................................................4
Loop Plumbing Diagram..............................................................................................................................5
IntelliChlor SCG Plumbing Diagram ...........................................................................................................5
Pool Water Preparation ...............................................................................................................................6
Determining Pool Size (Gallons of Water in Your Pool) ..........................................................................6
Determining Pool Size (liters of water in your pool)...............................................................................6
Section 1: IntelliChlor SCG Control Panel.................................................................................. 7
Salt Level Status LEDs ...............................................................................................................................7
Status LEDs................................................................................................................................................7
Sanitizer Output LED Indicators .................................................................................................................8
More and Less Output Buttons...................................................................................................................8
Self-Cleaning ..............................................................................................................................................8
Section 2: Pool Water and Chemistry, Conditions and Precautions ........................................9
Pool Water Chemistry, Conditions and Precautions ...................................................................................9
Optimum Pool Water Conditions for Salt Water Pools (using the IntelliChlor Salt Chlorine Generator) ...10
Covered Pools and Vinyl Liner Pool and Lowering Chlorine Output Levels .............................................. 10
Chlorine Testing ........................................................................................................................................11
What Type of Salt to Use ..........................................................................................................................11
How Much Salt to Use? ............................................................................................................................ 11
Calculating the Saturation Index ............................................................................................................... 12
TDS Factor ...........................................................................................................................................12
Langelier Saturation Index Factors.......................................................................................................12
How to Add Salt to the Pool ......................................................................................................................13
Table 1.Approximate Pounds (Kg) of salt needed to obtain 3,400 ppm in pool .............................13
Table 2. Approximate amount of stabilizer (cyanuric acid) to obtain 40 ppm in pool ....................14
Section 3: Operating IntelliChlor SCG ......................................................................................15
Initial Start-up Period................................................................................................................................15
Operation..............................................................................................................................................15
Use of an external Pool Pump Timer is not required ............................................................................ 15
If you use a Pool Pump Timer ..............................................................................................................15
Start-up Procedure (Super Chlorination) ..................................................................................................16
Sanitizer Output Settings and Adjustments..............................................................................................16
Operating in Winter ................................................................................................................................... 16
General Recommendations .................................................................................................................. 17
General Cautions.................................................................................................................................. 17

ii
IntelliChlor Electronic Chlorine Generator Installation and User’s Guide
Section 5: Installation ................................................................................................................21
Kit Contents .............................................................................................................................................. 21
Required Tools ..........................................................................................................................................21
IntelliChlor “Dummy” Cell.......................................................................................................................... 22
Selecting Model Size - IntelliChlor Model IC20, IC40, IC60 .....................................................................22
Installing the IntelliChlor Cell Assembly ...................................................................................................22
Connecting the Cell Power Cable to the Power Center ........................................................................23
Connecting the Power Supply Cable to the IC15 Cell .......................................................................... 23
Connecting IC20, IC40, IC60 Power Center to IntelliTouch, EasyTouch or SunTouch System............24
Connecting IntelliChlor Communication Cable (RS-485) .................................................................25
Connecting IntelliChlor to a SunTouch System ....................................................................................26
Wiring AC Power from IntelliChlor SCG and IntelliFlo to Automation Control System
(IntelliTouch, EasyTouch and SunTouch Automation Control System) ..................................................... 26
Section 6:Troubleshooting .......................................................................................................28
Table 1: Troubleshooting ..........................................................................................................................28
System Specifications - 110 VAC and 220 VAC Wiring ............................................................................ 30
220 VAC Basic System Wiring ............................................................................................................. 30
110 VAC Basic System Wiring .............................................................................................................31
IC15SCG System SpecificationsandWiring...............................................................................33
Customer Support
8 A.M. to 7:30 PM
Phone: [phone]
Fax: [phone]
Download the IntelliChlor Userʼs Guide (PDF)
http://www.pentairpool.com/pdfs/IntelliChlorOM.pdf
http://www.pentairpool.com/pdfs/IntelliChlorIC15IG.pdf
Section 4: User Maintenance .................................................................................................... 18
Daily service ............................................................................................................................................ 18
Weekly service.........................................................................................................................................18
Monthly Service........................................................................................................................................18
Usage Hours Meter ..................................................................................................................................19
Cleaning the IECG Cell Blades.................................................................................................................19
Winterizing................................................................................................................................................20
Contents (continued)

iii
IntelliChlor Electronic Chlorine Generator Installation and User’s Guide
Important Notice: Attention Installer: This manual contains important information about the
installation, operation and safe use of this product.This information should be given to the owner and/or
operator of this equipment.When installing and using this electrical equipment, basic safety precautions should
alwaysbe followed, including thefollowing:
WARNING:IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. READ AND FOLLOW ALL
INSTRUCTIONS.
Before installing this product, read and follow all warning notices and instructions which are
included. Failure to follow safety warnings and instructions can result in severe injury,
death, or property damage. Call [phone] for additional free copies of these
instructions, or obtain a copy of these instructions at:
WARNING: To reduce the risk of injury, do not permit children to use this product.
WARNING: CHLORINE GAS BUILDUP CAN OCCUR WITH IMPROPERWIRING: Toreducethe risk of
personal injury the IntelliChlor
®
Salt Chlorine Generator (SCG) Power Center must be installed on and
wirded to the load side of the time clock, electronically controlled switch, or relay load side, so that it will
receive power only when the pool pump is on. Otherwise, dangerous chlorine gas buildup can occur. The
IECG should never be energized when the pool pump is OFF and water is not flowing through the unit.
WARNING: To reduce the risk of injury, service should only be personnel by a qualified pool
service professional.
WARNING: Never operate the IIntelliChlor Salt Chlorine Generator (SCG) without proper flow or
water circulation. A build-up of flammable gases will result in hazardous conditions.
CAUTION - IntelliChlor Salt Chlorine Generator (SCG) is for use with permanently-installed pools and
may also be used with hot tubs and spas if so marked. Do not use with storable or steel pools. A
permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily
disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for
storage and reassembled to its original integrity.
CAUTION - When using the IntelliChlor Salt Chlorine Generator (SCG) with an IntelliTouch
®
,
EasyTouch
®
or SunTouch
®
Control System, always wire the IntelliChlor Salt Chlorine Generator (SCG)
Power Center to the pump side of the relay located in the IntelliTouch, EasyTouch or SunTouch load center.
This wiring method does not require a ground fault circuit-interrupter (GFCI) to protect the circuit. A green
colored terminal (or a wire connector marked “G”, “GR”, “Ground” or “Grounding”) is provided within the
terminal compartment in the Power Center transformer enclosure. To reduce risk of electric shock,
connect this terminal or connector to the grounding terminal of your electric service or supply panel with a
conductor equivalent in size to the circuit conductors supplying this equipment. The power supply must be
interconnected with pool pump motor power source.This insures the SCG and pool pump will switch on
and off together.
SAVE THESE INSTRUCTIONS
IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS
http://www.pentairpool.com/misc/owners_manuals/sanitizers/IntelliChlor_Owners.pdf

iv
IntelliChlor Electronic Chlorine Generator Installation and User’s Guide
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
CAUTION - Use of chemicals other than those recommended may be hazardous.Even proper use of the
recommended chemicals can be hazardous.Follow the Chemical Manufacturer’s Instructions.
CAUTION - To reduce the risk of electric shock, install IntelliChlorSalt Chlorine Generator (SCG)
a minimum of five (5) feet away from the inside wall of the pool.
CAUTION - Install the IntellliChlor SCG a minimum of three (3) feet away from the heater outlet.
CAUTION - A solid copper, bonding conductor not smaller than No. 8 AWG (8.4 mm) should be
connected from the accessible wire connector on the unit to all metal parts of the swimming pool, spa, or hot
tub structure and to all electrical equipment, metal conduit, and metal piping within five (5) feet (1.5 m) of the
inside walls of a swimming pool, spa, or hot tub, when the unit is installed within five (5) feet of the inside
walls of the swimming pool, spa, or hot tub.
Canada - Industry Canada (IC) -ThisdevicecomplieswithRSS210 of Industry Canada.(1999)
FCC Standard - 47 CFR Part 15, Subpart C (Section 15.247).This version is limited to chapter 1 to chapter 11
by specified firmware controlled in the U.S.A.
Federal Communications Commission (FCC) -This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Interference Statement -This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.However, there is no guarantee that interference will not occur in a
particular installation.If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Modifications not expressly approved by the party responsible for FCC compliance could void the user’s
authority to operate the device.
SAVE THESE INSTRUCTIONS
W ARNING: When mixing acid with water, ALWAYS ADD ACIDTO WATER. NEVER ADD
WATER TO ACID.
CAUTION - The IntelliChlor IC15 Power Supply must be interconnected with pool pump motor power
source.This ensures the IntelliChlor SCG and pool pump will switch on and off together. When the
IntelliChlor SCG IC15 is installed in Europe.The IntelliChlor IC15 power supply fuses must ONLY be
obtained from the manufacturer.
WARNING - The IntelliChlor IC15 Power Supply is only intended for use with the IntelliChlor SCG IC15
cell, DO NOT PLUG ANY OTHER INTELLICHLOR CELL INTO THIS POWER SUPPLY, SEVERE DAMAGE
WILL RESULT.

1
IntelliChlor®Salt Chlorine Generator Installation and User’s Guide
IntelliChlor
®
Salt Chlorine Generator (SCG) Overview
The IntelliChlor Salt Chlorine Generator (SCG) uses a process known as electrolysis to produce chlorine gas
which immediately dissolves into a solution to create Hypochlorite and Hypochlorous acid pool and spa water
sanitizer from a low concentration of salt added to the pool water. Hypochlorite and Hypochlorous kill bacteria,
oxidizes organic material, and kills algae, then reverts back to salt. The IntelliChlor SCG then reuses the salt and
the process starts over again. The IntelliChlor SCG residential system is comprised of the IntelliChlor SCG cell
and Power Center.
FOR ALL NEWLY CONSTRUCTED OR RESURFACED PLASTER POOLS: Do not operate the IntelliChlor
SCG with newly poured or resurfaced pool plaster. Salt is a corrosive element and severe salt damage
can occur to your pool. Wait at least ONE (1) MONTH after construction to allow plaster to cure
before adding salt and operating IntelliChlor SCG. Follow the pool surface manufacturerʼs guidelines
for your specific pool. FOR NEW VINYL LINER POOLS, contact the manufacturer for recommended
guidelines before adding salt and operating the IntelliChlor SCG.
The IntelliChlor SCG is designed only to produce chlorine. The IntelliChlor SCG does not monitor or control
chlorine levels in the pool or spa water. It is the pool ownerʼs responsibility for monitoring and maintaining
free chlorine levels at the APSP recommended range of 2.0 to 4.0 parts per million (ppm). It is the pool
ownerʼs responsibility to check, on a regular basis, the free chlorine level while the pool pump is running, and
adjust the IntelliChlor SCG accordingly.
Salt is an inherently corrosive material. While the levels of salt required for proper operation of the
IntelliChlor SCG are relatively low when compared to sea water and other salt solutions, placing any amount
of salt in your pool increases the likelihood of corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Metal parts (including steel pools) and certain natural and man-
made surfaces are particularly susceptible to corrosion and deterioration when used in and around salt
water pools. Pentair Water Pool and Spa, Inc. (“Pentair”) does not represent or otherwise guarantee that the
proper use of the IntelliChlor SCG will prevent corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Consult your experienced pool professional, who should be able to
advise you on the proper material selection, installation techniques for those materials, and the proper use,
care and maintenance of those materials for your specific pool type and location in order to minimize the
corrosion and deterioration that is inherent in and around salt water pools.
IntelliChlor®SCG Models
An IntelliChlor Salt Chlorine Generator system consists of one or more of the following. Note: The cell will
produce pure chlorine per 24 hours of continuous pool pump run time.
•
PC100 (P/N 520556): Power Center
Kit (sold separately). Provides power
and control communication to and from
the IntelliChlor cell. Used for IC20,
IC40 and IC60 IntelliChlor SCG cell.
•
IntelliChlor “pass-through” cell
(P/N 520588):
For new pool start-up.
Note: IC15 cell includes Power Supply (P/N 520888).
SU: e z i Sl ooP
) ret iL(. laG
decudo r Pen i r o l hC
4 2r e P) . gK( . sbL
r uoH
l l eC5 1C I
888025N/ P( )
) 187 (000 , 517)2.0(06.0
l l eC0 2C I
)455025N/ P(
) 57 (000 , 0)223.0(07.0
l l eC0 4C I
555025N/ P(
) 051 (000 , 0)446.0(04.1
l l eC0 6C I
)501025N/ P(
) 722 (000 , 0)61. 0 (2

2
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
IntelliChlor SCG Control Panel and Cell Description
The IntelliChlor SCG includes a control panel with buttons and LED indicators to control the
IntelliChlor SCG and produce chlorine (see page 7). The IntelliChlor SCG measures the water
temperature and salt level to produce chlorine at the defined output. If the salt level in the pool water
is too low (red on salt display), the cell is turned off until salt is added to the pool. The SCG cell has
a self-cleaning cycle which reverses the cell polarity, reducing calcium buildup. This feature turns the
cell on and off at regular intervals to minimize calcium and scale buildup and further maximizes cell
life (see page 15).
System Components
The chlorine production can be varied by either adjusting the sanitizer output level on the control
panel and/or by varying the number of hours the IntelliChlor SCG is on each day. The IntelliChlor
SCG automatically reverses the cell electrode blades every few hours to help clean the cell. This
process does not interrupt the production of Chlorine.
•Flow Sensor: A flow sensor assures that there will always be adequate water flow through
the IntelliChlor SCG. If the IntelliChlor SCG is not properly plumbed and/or does not
receive adequate water flow, no chlorine will be produced.
•Temperature Sensor: To protect the IntelliChlor SCG from operation and potential
damage when the temperature of the pool water falls below 52° F, ±3° F (11° C, ±1.67°
C), the temperature sensor switches the IntelliChlor SCG off, illuminates the COLD
WATER light and no chlorine will be produced.
•Salt Sensor: Two (2) salt sensor probes in the IntelliChlor SCG are activated each time
the IntelliChlor SCG is switched on and again during every 12 hours of operation. At
each of those times, the salt level LED indicator lights flash in a scrolling sequence for
two (2) minutes to indicate that the IntelliChlor SCG is in analysis mode. After two (2)
minutes, the LED indicators lights will signal one (1) of three (3) salinity ranges. For more
information, see “Salt Level Status LEDs” on page 7.
Note: The salt sensor reading is within +/- 500 ppm accuracy.
IntelliChlor
®
Salt Chlorine Generator (SCG) Cell
Water flow in
Control Panel status LEDs
MORE and LESS output buttons
Internal Flow
Switch
Water flow out
Cell Union Coupling
with o-ring
Cell Union Coupling
with o-ring (2x)

3
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
IntelliChlor
®
SCG Power Center (IC20, IC40 IC60)
The IntelliChlor Power Center converts AC electrical current to a low-voltage DC electrical current which is
required to produce chlorine. The power supply is connected with the pool circulation pump electrical source so
that the IntelliChlor SCG only operates when the pool pump is on. The Power Center should be mounted
vertically on the wall up to fifteen (15) feet away from the IntelliChlor SCG. The Power Center contains the
transformer, fuse, connector to the cell and the AC electrical current wiring configuration with the DC electrical
current output cable to the IntelliChlor SCG. A fuse is mounted on circuit board inside the enclosure for
additional protection. There are no other controls or lights on the Power Center. For information about installing
and proper use of the Power Center, see the “IntelliChlor Power Center Installation Guide,” (P/N 520590).
IntelliChlor SCG Power Center (Model PC 100).
Used with IC20, IC40 IC60
CAUTION - Before plugging or
unplugging the IntelliChlor SCG to the
Power Center, first switch off the AC
power to the Power Center.
The IntelliChlor SCG IC15 Power Supply converts AC electrical current to a low-voltage AC electrical current
which is required to produce chlorine. The Power Supply should be connected with the pool circulation pump
electrical source so that the IntelliChlor SCG only operates when the pool pump is on. A 15 ft. cord connected
to the IC15 unit plugs into the Power Supply which plugs directly into a 110VAC outlet. The Power Supply can
be mounted vertically on the wall up to fifteen (15) feet away from the IntelliChlor SCG.. The Power Supply
contains the transformer, fuse (1.5 AMP 250 V, 3 AG), connector to the cell and the AC electrical cord with
plug. There are no other controls or lights on the Power Supply. The Power Supply must be connected to a
GFCI protected outlet.
IntelliChlor SCG IC15 External Power Supply
IntelliChlor SCG IC15 Power Supply
WARNING: CHLORINE GAS BUILDUP
CAN OCCUR WITH IMPROPER WIRING: To
reduce the risk of personal injury the IntelliChlor
SCG Power Center must be installed on and
wirded to the load side of the time clock,
electronically controlled switch, or relay load
side, so that it will receive power only when the
pool pump is on. Otherwise, dangerous chlorine
gas buildup can occur. The IntelliChlor SCG
should never be energized when the pool pump
is OFF and water is not flowing through the unit.
WARNING: CHLORINE GAS BUILDUP
CAN OCCUR WITH IMPROPER WIRING: To
reduce the risk of personal injury the IntelliChlor
SCG Power Center must be installed on and
wirded to the load side of the time clock,
electronically controlled switch, or relay load
side, so that it will receive power only when the
pool pump is on. Otherwise, dangerous chlorine
gas buildup can occur.The IntelliChlor SCG
should never be energized when the pool pump
is OFF and water is not flowing through the unit.
CAUTION - First
switch OFF AC power to
the Power Supply before
plugging or unplugging the
IntelliChlor IC15.

4
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
System Schematic Diagram
The following schematic diagram shows a typical IntelliChlor
®
SCG system installation.
Note: Refer to the relevant portions of this Installation and User’s Guide for information regarding proper
placement and spacing of all equipment depicted in the schematic diagram shown below. The schematic
diagram is not drawn to scale. .
Install Chlorine/Bromine Feeders after the IntelliChlor
®
SCG Cell
CAUTION - To avoid permanent damage to the IntelliChlor SCG cell, in-line chlorine/bromine feeders
(such as Pentair Aquatic SystemsRainbow
®
models) MUST be installedAFTER the IntelliChlor SCG cell as
shown below. When using the IntelliChlor SCG with an in-floor cleaning system, it is recommended that a
separate return line be used for the cleaner to reduce the increased water pressure stress on the IntelliChlor cell.
Note: For best flow
sensing, provide at least
12"-18" of straight pipe in
front of the cell inlet.
Note: (*) Install IntelliChlor SCG cell
vertically for best performance.
(**) The IntelliChlor SCG should
be at least three (3) feet away
from the heater outlet.
IntelliChlor SCG System Schematic Diagram
Pool pump and Power
center MUST be wired to
ON/OFF switch together.
24-hour pool pump timer,
switch or controller
IntelliChlor SCG Power Center. Provdied VDC
electrical supply (see IntelliChlor SCG Power Center
Installation Guide P/N 520590)
115/230 VAC
electrical power
supply
(*) IntelliChlor
SCG
cell
Automatic
Chlorine/Bromine
Feeder
Return to Pool
From Pool
To Drain
(Backwash)
Filter
Heater **
Pump























Not to scale




5
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
Not to scale
IntelliChlor SCG Plumbing Diagram
Plumbing the IntelliChlor
®
Salt Chlorine Generator:
• Always install the IntelliChlor SCG AFTER the filter and heater (see “System Schematic Diagram”
on page 4). The IntelliChlor SCG should be at least three (3) feet away from the heater outlet.
• If the IntelliChlor SCG is installed on a pool/spa combination system, install (see diagram below) the
IntelliChlor SCG BEFORE the pool/spa return valve to allow proper chlorination of both the pool
and spa and also to avoid creating gas being traped in the pool plumbing.
Loop Plumbing Diagram
The IntelliChlor
®
SCG is designed to operate with water flow rates from 25 +/- 5 gallons per minute (gpm) up to
105 gpm. Refer to the pipe manufacturer specifications for recommended maximum flow rate. For flow rates
over 80 gpm you must use a bypass loop (as shown below) for best chlorine production. Installations with flow
rates over 80 gpm include those that have in-floor cleaning systems or booster pumps. These systems MUST
use a bypass loop with the IntelliChlor SCG with a flow control valve that assures that the flow through the
IntelliChlor SCG is maintained within its designed operating water flow rates.
NOT TO SCALE
Note: For best flow
sensing, provide at least
12"-18" of straight pipe in
front of the cell inlet.
IntelliChlor SCG Cell
IntelliChlor SCG System Loop Plumbing Diagram
IntelliChlor SCG System Plumbing Diagram
Note: Install IntelliChlor
SCG cell vertically for best
performance.

6
IntelliChlor®Salt Chlorine Generator Installation and User’s Guide
Pool Water Preparation
Determining Pool Size (Gallons of Water in Your Pool)
•Rectangular Pools: Length x width x average depth x 7.5
•Circular Pools: Diameter x diameter x average depth x 5.9
•Oval Pools: Length x width x average depth x 6.7
•Sloping Sides: Multiply total gallons by 0.85 = gallon capacity
Determining Pool Size (liters of water in your pool)
•Rectangular Pools: Length x width (meters) x average depth x 1000
•Circular Pools: Diameter x diameter x average depth x 785
•Oval Pools: Length x width (meters) x average depth x 893
•Sloping Sides: Multiply total liters by 0.85 = liter capacity.
CAUTION - Never use dry acid (sodium bisulfate) to adjust pH in arid geographic areas with
excessive evaporation and minimal dilution of pool water with fresh water. A buildup of byproducts
can damage the IntelliChlor®SCG.

7
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
Section 1
IntelliChlor
®
SCG Control Panel
Salt Level Status LEDs
The IntelliChlor SCG checks the pool salinity water daily and displays the
levels as follows:
Green LED: Good salt. The pool water salt level is between 2800
ppm and 4500.
Green LED (Flashing): Salt level is above 4500 ppm. The salt level
is high which increases the risk of corrosion and deterioration of pool
equipment and surfaces in and around the pool.
Red LED:
Low salt. The water salt level is below 2800 ppm. The
IntelliChlor SCG will be producing chlorine at reduced efficiency. It is
highly recommended to add salt. See (*) Note below.
Red LED:
Very low salt . The water salt level has fallen below 2600
ppm. The IntelliChlor SCG will not produce chlorine until salt is
added. The IntelliChlor SCG is OFF. See (*) Note below.
NOTE (*): After every salt addition, pump should be allowed to
run for at least 24 hours for proper dilution. Salinity readings
should only be taken, after the dilution period.
Status LEDs
Cold Water: Shows the IntelliChlor SCG power status:
•No Light: The IntelliChlor SCG is operating in the normal
temperature range (> 52° F (11° C)
•Red: The IntelliChlor SCG is in “Standby” mode (system off,
no chlorine production) due to a cold water condition. The
IntelliChlor SCG will resume to normal operation mode,
including accurate salinity report, once water temperature
goes above 52° F (11° C).
Cell: Shows the status of the IntelliChlor SCG.
•Green (flashing): The IntelliChlor SCG needs to be
inspected. The blades may have calcium buildup. The
IntelliChlor SCG is not producing chlorine.
•Green: IntelliChlor SCG is good and producing chlorine
No Light: IntelliChlor SCG is off and not producing chlorine.
It may be in an off-period of the sanitizing cycle and will
return on shortly.
Flow: This light indicates the status of water flowing through the
IntelliChlor SCG.
•Red: Insufficient water flow through the IntelliChlor SCG, no chlorine is being produced.
•Green: Sufficient water flow to produce chlorine.
SWIMMING POOL AND SPA CHLORINATOR







Sanitizer Output LED indicators: See page 8.
Less / More Buttons: Controls the percentage of the total output capacity that the IntelliChlor SCG is
producing while the pump is on (see Sanitizer Output LED indicators above). See page 8.








8
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
More and Less Output Buttons
The More and Less buttons control the percentage of the total output capacity that the IntelliChlor SCG is
producing while the pump is on (see Sanitizer Output LED indicators above).The lights act as a bar graph: the
more lights that are on, the more chlorine is produced. Blinking LEDs represent 2%, 4%, 6%, 8% & 10% while
solid LEDs represent 20%, 40%, 60%, 80% and 100%.Slide the panel cover up to access the More, Less and
Boost On/Off buttons. Note: When an IntelliChlor is connected to an IntelliTouch
®
,EasyTouch
®
or SunTouch
®
Control System, the Less and More buttons are disabled and IntelliChlor SCG Sanitizer Output is controlled
externally.
More: Increases the output of the cell in 2% increments up to 10% and then 20% increments. Example: The
Sanitizer Output display is showing 8%. Pressing the MORE button once will blink the 10% light. The unit will
produce chlorine at 10% of total capacity. Pressing MORE again will turn on the 20% light, and so on until all
five (5) lights are on solid.
Less: Decreases the time the cell produces chlorine, in either 2% or 20% increments (from 20% to 100%).
Example: The Sanitizer Output display is showing 40%. Pressing the LESS button once will turn off the 40%
light, leaving only the 20% light. The unit will produce 20% of total capacity of the cell. Pressing LESS again
will turn go to 10% (all 5 LEDs blinking).
Boost On/Off: Press both the More and Less buttons together to turn Boost mode on or off. Boost mode sets
the sanitizer output to run 100% for the next 24 hours of pool pump run time. If the time clock switches off the
pump cycle, then switches power back on the next day, Boost mode will continue until 24 hours has elapsed
since Boost mode was turned on or Boost mode is canceled by the user. The Sanitizer Output display will scroll
the output LEDs to indicate Boost mode.
The self-cleaning feature reduces scale buildup on the blades of the IntelliChlor SCG. The self-cleaning cycle
tends to reduce the life of the IntelliChlor SCG, therefore, it should be used only to the extent necessary to
minimize the scale buildup on the blades. It is factory set to two (2) hours for the first 30 days of operation,
then automatically switches to three (3) hours.
0% No LEDs lit - No chlorine produced - IntelliChlor SCG is off.
2% 1 LED blinking Produces chlorine for 64 seconds of every hour.
4% 2 LEDs blinking Produces chlorine for 127 seconds of every hour.
6% 3LEDs blinking Produces chlorine for 16 seconds of each 5 minute period.
8% 4 LEDs blinking Produces chlorine for 21 seconds of each 5 minute period.
10% 5 LEDs blinking Produces chlorine for 27 seconds of each 5 minute period.
20% 1 LED solid Produces chlorine for 53seconds of each 5 minute period.
40% 2 LEDs solid Produces chlorine for 106 seconds of each 5 minute period.
60% 3LEDs solid Produces chlorine for 159 seconds of each 5 minute period.
80% 4 LEDs solid Produces chlorine for 212 seconds of each 5 minute period.
100% 5 LEDs solid Produces chlorine for 265 seconds of each 5 minute period.
Operator Control Panel (continued)
Sanitizer Output LED Indicators
The five (5) LED indicators display as a bar graph to show the cell output in either 2% or 20% increments, the
percentage of the total output capacity of chlorine being produced. Percentages from 2% to 10% are
represented by blinking LEDs. Percentages from 20% to 100% are represented by solid LEDs. In BOOST
mode, these LEDs scroll from left to right.
Self-Cleaning

9
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
Section 2
Pool Water Chemistry, Conditions and Precautions
This section describes the start up procedure and operating instructions for IntelliChlor
®
SCG.
Pool Water Chemistry, Conditions and Precautions
1. New Pool Water: A recently filled or newly-refinished pool may contain undesirable matter. This
undesirable matter could interfere with the IntelliChlor SCG’s ability to chlorinate properly. Make
sure the water is tested by a pool professional and properly balanced before switching on the
IntelliChlor SCG.
2. Super Chlorination burns out the swimmer waste that has combined with chlorine. This frees the
chlorine for sanitizing. This is accomplished by raising the chlorine level quickly and dramatically.
When the chlorine level is raised to ten (10) times the amount of combined chlorine the pool water is
said to have been super chlorinated. As pool water is continuously passed through the IntelliChlor
SCG while the unit is powered on, the water inside the IntelliChlor SCG is being super chlorinated.
Note: On initial start-up of a pool, it is best to super chlorinate using an outside source, i.e., use
a shock treatment available at your local pool supplier.
3. Chloramines should not be present in pool water. Chloramines are formed when ammonia (which is
found in urine and sweat) combine with free chlorine. This ties up the free chlorine in your pool and
does not allow the chlorine in your pool to disinfect. Chloramines also burn the eyes and are foul
smelling. Super Chlorinate to remove chloramines at the initial start-up of the pool and as needed to
maintain proper levels of free chlorine.
4. Cyanuric acid is needed in outdoor pools to help to stabilize and maintain proper levels of chlorine.
90% of unstabilized chlorine is destroyed by the UV radiation from the sun within two hours.
Cyanuric acid stabilizes chlorine in water from UV degradation. When using the IntelliChlor SCG, the
cyanuric acid level should be maintained between 30-50 ppm. See Table 2, on page 13. NOTE: DO
NOT USE CYANURIC ACID IN INDOOR POOLS.
5. Total Dissolved Solids (TDS): Adding salt to pool water will raise the TDS level. While this does
not adversely affect the pool water chemistry or clarity, the pool water professional testing for TDS
must be made aware salt has been added to the IntelliChlor SCG system. The individual performing
the TDS test (see page 19) may then subtract the salinity level to arrive at a TDS level that would
be compatible to a TDS reading for a non-salt water pool.
Continue on next page.
Salt is an inherently corrosive material. While the levels of salt required for proper operation of the
IntelliChlor SCG are relatively low when compared to sea water and other salt solutions, placing any amount
of salt in your pool increases the likelihood of corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Metal parts (including steel pools) and certain natural and man-
made surfaces are particularly susceptible to corrosion and deterioration when used in and around salt
water pools. Pentair Water Pool and Spa (“Pentair”) does not represent or otherwise guarantee that the
proper use of the IntelliChlor SCG will prevent corrosion or other deterioration of pool equipment and any
surfaces used in and around your pool. Consult your experienced pool professional, who should be able to
advise you on the proper material selection, installation techniques for those materials, and the proper use,
care and maintenance of those materials for your specific pool type and location in order to minimize the
corrosion and deterioration that is inherent in and around salt water pools.
CAUTION: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged especially in
arid regions where pool water is subject to excessive evaporation and is not commonly diluted with
fresh water. Dry acid can cause a buildup of by-products that can damage your chlorinator cell.

10
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
6. Metals - Some metals, i.e. copper and iron, can cause loss of chlorine. Also, metals can stain your
pool. Metals can also damage the IntelliChlor
®
SCG. Have your local pool professional check for
metals and recommend methods of removal.
7. Nitrates and Phosphates can cause extremely high chlorine demands and will deplete chlorine from
your swimming pool. In some cases nitrates may even lower your chlorine levels to zero. Your local
pool professional can test for nitrates and phosphates. While a 0 ppm level of nitrates is the ideal, the
pool owner should make sure that nitrates DO NOT exceed 10 ppm. Phosphates should not exceed
125 parts per billion (ppb).
Optimum Pool Water Chemistry Conditions for Salt Water Pools
(using the IntelliChlor SCG)
In accordance with the Association of Pool and Spa Professionals (APSP) standards, it is recommended that the
following pool water chemistry conditions be maintained on an on going basis to help protect pool users, pool
related equipment and surfaces in and around the pool. These values are important to maintaining the pool
equipment in proper operating condition and preventing corrosion. For more information, refer to your local
agency having jurisdiction, NSPI (National Spa and Pool Institute), the CDC (Centers for Disease Control), or
the WHO (World Health Organization).
Free Chlorine: 2.0 - 4.0 ppm. Above 4.0 ppm may cause corrosion of metal components
Combined Chlorine (Chloramines): None (super chlorinate to remove all chloramines)
pH: 7.2 - 7.8(USE MURIATIC ACID to lower pH and Soda Ash to raise pH.)
Cyanuric Acid: 30 - 50 ppm
Total Alkalinity: 80 - 120 ppm
Calcium Hardness: 200 - 400 ppm
TDS (includes salt): 3000 minimum to 5700 to 6000 maximum ppm
Salt: 3600 - 4500 ppm (ideal 3600 ppm)
Metals (Copper, Iron, Manganese): None
Nitrates: None
Phosphates: Less than 125 ppb
Saturation Index -.3to .3 (zero (0) best)
Covered Pools and Vinyl Liner Pool and Lowering Chlorine Output Levels
When using the IntelliChlor SCG with covered pools and/or vinyl liner pools, less chlorine is needed. It is
recommend to lower the chlorine output level while the pool is covered. For more information about chlorine
output levels, see “More or Less Output Buttons” page 8.
Pool Water Chemistry, Conditions and Precautions (Continued)

11
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
ChlorineTesting
It is recommended that chlorine test samples be taken from two (2) locations in the pool. Compare the
samples. A higher level should be found at the pool return line. The higher level at the pool return line indicates
the IntelliChlor
®
SCG is producing chlorine. Take chlorine samples for testing at:
• The pool return line.
• 18 inches (457 mm) below the surface and well away from the pool return line.
What Type of Salt to Use
Use salt that is at least 99.8% pure NaCl, sodium chloride. The preferred and recommended salt is an
evaporated, granulated, food quality, non-iodized salt with no additives. Consult your salt supplier.
• Avoid using salt with anti-caking agents (sodium ferrocyanide, also known as YPS or yellow
prussiate of soda). Filling agents can cause some discoloration of fittings and surface finishes in pool.
• Water conditioning salt pellets are compressed forms of evaporated salt and may be used, but will
take longer to dissolve. Such pellets could damage pool plaster and other surfaces in and around the
pool.
• Do not use calcium chloride or potassium chloride as a source of salt. (Use sodium chloride only).
• Do not use Rock salt (insoluble impurities mixed with the rock salt can shorten the life of the
IntelliChlor SCG.
How Much Salt to Use?
Use Table 2 (page 14) to determine how much salt will be needed. Most pools contain some salt, depending on
the water source and chemicals used for sanitizing. Therefore, the pool owner must always test salt levels before
adding salt. A hand held meter calibrated for NaCl (salt) can be used to determine the salt levels of the water.
After the IntelliChlor SCG is powered on, the LED salt level lights will blink from bottom to top for two (2)
minutes while it analyzes the pool water, then the LED indicators will show one (1) of four (4) salt level ranges.
See “Salt Status LEDs” on page 7 for more information.
• 3600 ppm of salt is recommended for optimum water condition.
• Low salt concentration below 2600 ppm will cause the unit to turn off
• High salt concentration above 4500 ppm may cause excessive corrosion or deterioration to pool
equipment and surrounding surfaces in and around the pool.
Note: Salt measurements will vary between measuring devices (salt test strips, electronic testers, and
titration). The salt sensor reading is within +/- 500 ppm accuracy. For more troubleshooting
information about high salt levels, see “Troubleshooting,” on page 28.
FOR NEW VINYL LINER POOLS, contact the manufacturer for recommended guidelines before adding
salt and operating the IntelliChlor SCG.
CAUTION - FOR ALL NEWLY SURFACED PLASTER POOLS: Do not operate the IntelliChlor SCG
with newly surfaced pool plaster. Salt is a corrosive element and severe salt damage can occur to your
pool. Wait at least ONE (1) MONTH after construction to allow plaster to cure before adding salt and
operating IntelliChlor SCG. Follow the pool surface manufacturerʼs guidelines for your specific pool.

12
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
SI = pH + CHF + AF + TF + TDSF
Satura-
tion
Index
pH as
tested
Calcium
Hardness
Factor
Alkalinity
Factor
Tempera-
ture
Factor
TDS
Factor
Calculating the Saturation Index
The saturation index is a formula that measures a solution ability to dissolve or deposit calcium carbonate and is
used as an indicator of the corroosivity of the solution and temperature. A well balanced water will have a
formula result ranging between -0.3 and +0.3 Outside this range, the pool water is considered out of balance,
potentially damaging pool equipment or scaling the IntelliChlor SCG. The equation to calculate Si is:
Cyanuric acid in the form of cyanurate ions contribute to alkalinity. Thus, a correction must be made to total
alkalinity. We subtract 1/3of the cyanuric acid level from the reading obtained in the total alkalinity test.
Total Alkalinity - 1/3Cyanuric Acid = Corrected Alkalinity
This correction can be considerable in established pools with high cyanuric acid levels; for example, at 100
ppm cyanuric acid, the correction amounts to 33 ppm (100 ÷ 3= 33.3).
Note: Use the reading closest to your actual reading in choosing the factor.
Total alkalinity in this context refer to the total of carbonate and bicarbonate alkalinity. If cyanuric
acid is used, a correction factor must be used (see cyanuric acid Table 1 on page 13).
Langelier Saturation Index Factors
TDS Factor
<1000 12.10
1000 12.19
2000 12.29
3000 12.35
4000 12.41
5000 12.44
TDS Factor (Factors shown below are based on the actual measured value for the particular parameter)

13
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
How to Add Salt to the Pool
CAUTION - FOR ALL NEWLY SURFACED PLASTER POOLS: Do not operate the IntelliChlor SCG with
newly surfaced pool plaster. Salt is a corrosive element and severe salt damage can occur to your pool.
Wait at least ONE (1) MONTH after construction to allow plaster to cure before adding salt and operating
IntelliChlor SCG. Follow the pool surface manufacturerʼs guidelines for your specific pool. FOR NEW VINYL
LINER POOLS, contact the manufacturer for recommended guidelines before adding salt and operating the
IntelliChlor SCG.
1. Check salt level in the water before adding any salt to pool.
2. Determine the amount of salt from the following chart.
3. Slowly pour the salt around the outer perimeter of the pool for quick and even distribution. To
avoid clogging the filter or damaging pool related equipment and surrounding surfaces, do not
add salt through the skimmer or surge tank.
4. Brush the pool bottom and allow water to circulate for 24 hours to dissolve salt completely.
5. After 24 hours, verify correct salt level reading by checking the LED indicators on the IntelliChlor
SCG and by a separate reliable test method.
6. Power on the IntelliChlor
®
SCG and set the Sanitizer Output level to the proper setting to maintain
the appropriate free chlorine levels in the pool water (i.e., within the 2.0 - 4.0 ppm, APSP
recommended range).
Table 1. Approximate amount of stabilizer (cyanuric acid) to obtain 40 ppm in pool
NOTE: The cyanuric acid reading should be maintained at 30 - 50 ppm.
t n e r r uC
d i cAc i r un a yC
mp p - l e v e L
g000 , 01
) L000 , 83 (
g000 , 21
) L524 , 54 (
g000 , 41
) L000 , 35 (
g000 , 61
) L006 , 06 (
g000 , 81
) L731 , 86 (
g000 , 02
) L000 , 67 (
g000 , 22
) L003 , 38 (
g000 , 42
) L058 , 09 (
g000 , 62
) L124 , 89
g000 , 82
) L000 , 601
g000 , 03
) L000 , 431 (
0)gk74.1(52.3)gk77.1(09.3)gk6.2(55.4)g k6 3.2(02.5)gk56.2(58.5)gk49.2(05.6)g k4 2 . 3(51 . 7)gk35.3(08.7)gk38 .3(54 . 8)gk21.4(01.9)gk24.4(57.9
01 )gk01.1(34.2)g k2 3.1(29.2)gk45.1(04.3)gk67.1(98.3 ) gk89.1(73.4)gk02.2(68.4)gk24.2(53.5)gk46.2(38 .5)g k6 8. 2 (2 3.6)gk80.3(08.6)g k0 3.3(92.7
02 ) gk37.0(26.1)gk88 .0(49.1)gk30.1 (72 . 2)gk71.1(95.2)g k2 3.1(29.2)gk74.1(42.3)gk16.1(65.3)gk67.1(98.3 )gk19.1(12.4)gk50.2(45.4)gk02.2(68.4
See Table 2 (page 14) for approximate pounds (lbs) / kilogram (kg) of salt needed to obtain 3,600 ppm in
pool.

14
IntelliChlor
®
Salt Chlorine Generator Installation and User’s Guide
10,000 15,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 55,000 60,000
lbs 300.43 450.65 600.87 751.08 901.30 1051.52 1201.73 1351.95 1502.17 1652.39 1802.60 Kg 136.27 204.41 272.55 340.68 408.82 476.96 545.09 613.23 681.37 749.51 817.64 lbs 279.57 419.36 559.14 698.93 838.71 978.50 1118.28 1258.07 1397.85 1537.64 1677.42 Kg 126.81 190.22 253.62 317.03 380.43 443.84 507.24 570.65 634.05 697.46 760.86 lbs 258.71 388.06 517.41 646.77 776.12 905.47 1034.83 1164.18 1293.53 1422.89 1552.24 Kg 117.35 176.02 234.69 293.37 352.04 410.71 469.39 528.06 586.73 645.41 704.08 lbs 237.84 356.76 475.69 594.61 713.53 832.45 951.37 1070.29 1189.22 1308.14 1427.06 Kg 107.88 161.83 215.77 269.71 323.65 377.59 431.53 485.48 539.42 593.36 647.30 lbs 216.98 325.47 433.96 542.45 650.94 759.43 867.92 976.41 1084.90 1193.39 1301.88 Kg 98.42 147.63 196.84 246.05 295.26 344.47 393.68 442.89 492.10 541.31 590.52 lbs 196.12 294.17 392.23 490.29 588.35 686.41 784.47 882.52 980.58 1078.64 1176.70 Kg 88.96 133.43 177.91 222.39 266.87 311.35 355.83 400.30 444.78 489.26 533.74 lbs 175.25 262.88 350.51 438.13 525.76 613.39 701.01 788.64 876.26 963.89 1051.52 Kg 79.49 119.24 158.99 198.73 238.48 278.23 317.97 357.72 397.46 437.21 476.96 lbs 154.39 231.58 308.78 385.97 463.17 540.36 617.56 694.75 771.95 849.14 926.34 Kg 70.03 105.04 140.06 175.07 210.09 245.10 280.12 315.13 350.15 385.16 420.18 lbs 133.53 200.29 267.05 333.82 400.58 467.34 534.10 600.87 667.63 734.39 801.16 Kg 60.57 90.85 121.13 151.42 181.70 211.98 242.26 272.55 302.83 333.11 363.40 lbs 112.66 168.99 225.33 281.66 337.99 394.32 450.65 506.98 563.31 619.64 675.98 Kg 51.10 76.65 102.21 127.76 153.31 178.86 204.41 229.96 255.51 281.06 306.62 lbs 91.80 137.70 183.60 229.50 275.40 321.30 367.20 413.10 459.00 504.90 550.80 Kg 41.64 62.46 83.28 104.10 124.92 145.74 166.56 187.38 208.20 229.02 249.84 lbs 70.94 106.40 141.87 177.34 212.81 248.28 283.74 319.21 354.68 390.15 425.61 Kg 32.18 48.26 64.35 80.44 96.53 112.62 128.70 144.79 160.88 176.97 193.05 lbs 50.07 75.11 100.14 125.18 150.22 175.25 200.29 225.33 250.36 275.40 300.43 Kg 22.71 34.07 45.42 56.78 68.14 79.49 90.85 102.21 113.56 124.92 136.27 lbs 29.21 43.81 58.42 73.02 87.63 102.23 116.84 131.44 146.04 160.65 175.25 Kg 13.25 19.87 26.50 33.12 39.75 46.37 53.00 59.62 66.24 72.87 79.49 lbs 8.35 12.52 16.69 20.86 25.04 29.21 33.38 37.55 41.73 45.90 50.07 Kg 3.79 5.68 7.57 9.46 11.36 13.25 15.14 17.03 18.93 20.82 22.71
0
250 500
3,500 3,250 3,000
750
1,000 1,250 1,500 1,750 2,000 2,250 2,500 2,750
C U R R E N T S A L I N I T Y L E V E L
POOL SIZE IN GALLONS
Table 2. Approximate pounds (lbs) / kilogram (kg) of salt needed to obtain 3,600 ppm in pool